19 сағат бұрын
2 ай бұрын
2 ай бұрын
2 ай бұрын
2 ай бұрын
2 ай бұрын
Пікірлер
@kirkvivian9484 2 күн бұрын
Turned out pretty good!
@kirkvivian9484 4 күн бұрын
Hell yeah! Too bad the shopping cart didn't make an appearance.
@RecycledRacing 4 күн бұрын
It may in the future!!
@kirkvivian9484 4 күн бұрын
"You boys like Mexico! Whooooooooo!!!!"
@JohnWick-li2wz 5 күн бұрын
It's mexico! Nobody cares
@rawouch 7 күн бұрын
Video helped, thanks.
@RecycledRacing 7 күн бұрын
Glad it helped
@jasonbrinegar6759 9 күн бұрын
🤣🤣🤣Video noise!!
@RecycledRacing 9 күн бұрын
There was a lot going on in this video. Words got hard, apparently!! Thanks for watching!!
@b00sted_SS 11 күн бұрын
What’s it cost for coil overs all the way around? Sits right looks killer
@RecycledRacing 11 күн бұрын
The UMI front and rear kit is 1450. They have a 10% off sale for the fourth. It's worth every penny. The quality is unmatched.
@kirkvivian9484 12 күн бұрын
You need to tag....you know.
@RecycledRacing 12 күн бұрын
I almost added that....you know....will be there lol.
@Moore257 12 күн бұрын
Question. I have the pro dash went away for a month so disconnected battery. Came back to connected battery car started right up but my pro dash just has the top lights light up then goes out and the screen is black / blank. Have you had these issues or no where I should look
@RecycledRacing 12 күн бұрын
Every once and a while mine will freeze the screen when driving, or fail to boot up. I just recycle the key and it's usually fine. Double check your connections as always.
@Moore257 12 күн бұрын
@@RecycledRacing I’ve cycled it multiple times 20-30 times. Connections are all good and are all soldered. Mine use to not come on every 1 out of 6 times then cycled and it would be good. Now nothing and the only thing I did was disconnected the battery then reconnected 🤷♂️ my 3.5” screen works fine so I know it’s not the holley efi.
@kirkvivian9484 13 күн бұрын
Ha ha! Magnet stuck to the door frame.
@kirkvivian9484 13 күн бұрын
That's rad. 😊
@zachariahsmurray6789 13 күн бұрын
I can't wait to come out and meet you guys .anyone needs any custom work done. Hit me up .roll cage brackets rust repair, u name it. Locked in Doniphan. Thanks
@user-mv3uf8cr9f 23 күн бұрын
68 Malibu rubs doesn't it.
@RecycledRacing 22 күн бұрын
I haven't had anything rub yet.
@user-mv3uf8cr9f 22 күн бұрын
I meant it runs .
@ogresspeedshop 24 күн бұрын
Gotta love that single stripe left on the road… 😜🤣
@RecycledRacing 24 күн бұрын
Twice as many burnouts on the same set of tires lol
@ogresspeedshop 24 күн бұрын
@@RecycledRacing just gotta rotate em!!
@RecycledRacing 24 күн бұрын
Twice as often lmao
@kirkvivian9484 26 күн бұрын
Videos have come a long way man! Good job!
@RecycledRacing 26 күн бұрын
Glad you like them!
@justlistening9463 Ай бұрын
actualy not a bad idea how ever 4 / 3 grown men could tilt that on it side no problem. 🤔
@RecycledRacing Ай бұрын
That's 3/2 more grown men than I have available at my house. Its just me here. By myself. Gotta get creative!!
@justlistening9463 Ай бұрын
i seen that your making content gives you the fill in time keep up good workings thx .
@Carlover-qf5vy Ай бұрын
That’s my car!! You’re the one with the ls swapped Chevrolet right
@RecycledRacing Ай бұрын
I have the light blue chevelle.
@rjmzz430 Ай бұрын
Open rear....not seeing posi stripes!....?????
@RecycledRacing Ай бұрын
Unfortunately, plans are in motion for lots of upgrades. Had to take a break to recoup. Frame offs start adding up lol.
@haroldbirge6881 Ай бұрын
🫤When will Phil 👀
@RecycledRacing Ай бұрын
You will have to ask him. I don't know no phil.
@kevinposey7423 Ай бұрын
Needs a gumball on it like the GT40
@RecycledRacing Ай бұрын
It has one now!!! It was in the mail
@idk-oe5ow Ай бұрын
Nice car bro 🐢
@RecycledRacing Ай бұрын
It gives me a turtle head also
@idk-oe5ow Ай бұрын
@@RecycledRacing I just use that as my version of the standard smiley face, also is that a modern interior? If so, from what?
@RecycledRacing Ай бұрын
@@idk-oe5ow the seats are scat procar rally bucket seats. The center console is from a 2024 camaro. The dash is a holley pro dash. The rest is factory.
@idk-oe5ow Ай бұрын
@@RecycledRacing it all looks like something from the factory, good job bro 😎
@RecycledRacing Ай бұрын
@@idk-oe5ow thanks!! I tried.
@user-ss5gs2jt8u Ай бұрын
There's one problem there's 90 percent Chevrolet 😢😢😢😢😢
@RecycledRacing Ай бұрын
They were probably the only ones running🤣🤣🤣🤣🤣
@user-ss5gs2jt8u Ай бұрын
@@RecycledRacing pure Garbageeee
@samedymavie Ай бұрын
Bad ass color combo!!!
@elviscupp Ай бұрын
I'll have some smokey tires for next time
@RecycledRacing Ай бұрын
I need to get some disposables just for these events
@elviscupp Ай бұрын
@@RecycledRacing we prolly got some if you had some 16s for the car
@dew.adventures6712 Ай бұрын
Beautiful oldies 👍
@RecycledRacing Ай бұрын
Yes they are!
@elviscupp Ай бұрын
Are you sure the mic quit because i cant tell a difference 😂
@averageaquarium Ай бұрын
😂
@averageaquarium Ай бұрын
Heck yeah!
@Rumpleskin Ай бұрын
Boom boom room
@hannahhanyou Ай бұрын
⭐️ voice over, preferred actually!! 😂
@averageaquarium Ай бұрын
I couldn’t even tell the mic quit! The audio was dead on! 😂 Awesome video man.
@RecycledRacing Ай бұрын
I tried. Some of the noises I even made myself.
@p51sleeper95 Ай бұрын
Put one in my truck for power tour this year, wonder how many other people will have them in their cars?
@RecycledRacing Ай бұрын
I have seen some folks talk about being on channel 2. I guess we will see.
@user-mv9qo6qj3s Ай бұрын
Can you do a viedo on the Holley pro dash tach hookup. My tach is not working.
@kirkvivian9484 2 ай бұрын
Wish I coulda made it there with ya. We had other things on our plate.
@TurboMalibuV6 2 ай бұрын
Yes! You MUST use the sensor ground pin for your fuel gauge, or it won't read correct. I made that mistake also. I realized something was wrong with my fuel gauge when the automatic dimming of the display would brighten and dim down. The fuel gauge would also vary by about 1/4 of a tank. I then ran the fuel sender ground directly to the dash it was fixed. As far as ride height sensors, I used the Ford Expedition. Lincoln Navigator sensors from a You-Pull-It yard. Cost $7 each with the connectors. They are small, have built in bolt mount holes and use a ball joint type of connecting rod. The sensors have a short 3.5" total swing, so I lengthened the arm to get a total of 6" of suspension travel. 0-5 volts.
@RecycledRacing 2 ай бұрын
Oh! That's gold. Thanks for the info!!
@cwmotorsports4497 2 ай бұрын
Nice
@LuisTheQuicksterPlays 2 ай бұрын
Be careful with the spikes
@b00sted_SS 2 ай бұрын
Windows are all messed up on my 70’ , hopefully similar to yours and I’ll learn something here
@KCCamaro 2 ай бұрын
Thanks for the info! Just about to start my car on the holley finally and I was wondering how to make the gauge accurate. Subbed! I wish there was more doing holley tips and tricks out there. So many questions along the way with mine. I'm running a leash street strip and holley with a pro dash.
@RecycledRacing 2 ай бұрын
There a lot of turn signal and high beam indicator videos. But not much past that. I want to test and see what I can control or log with this dash. We will see what I can come up with.
@KCCamaro 2 ай бұрын
@@RecycledRacing that's actually what I'm more excited about than the car running. Lol. I like to tinker with electronics and see what all I can do with them. I am curious if I can feed my trans temp gauge to the screen, I just don't know the ohms to make it work and the wire is like a 22 gauge.
@RecycledRacing 2 ай бұрын
@@KCCamaro you can. Just have to set up an input and configure that input to a gauge. If you like electronics you came to the right place. I tinker as well.
@KCCamaro 2 ай бұрын
@@RecycledRacing I'll definitely have to keep up with the channel then!
@elviscupp 2 ай бұрын
Some sweet cars out there. Hopefully we won't get rained out next time
@stevemullin7472 2 ай бұрын
5:00 were those spring cushions part of the Stage 3 kit? I have the same kit and didnt get those and wondering if I need to make a call.
@RecycledRacing 2 ай бұрын
No. Im pretty sure I got them on Amazon because I didn't have anything in there.
@72grabbermav 3 ай бұрын
Great grill pattern!!!
@RecycledRacing 3 ай бұрын
The guy who made it said it really stood out to him.
@christianredden7197 3 ай бұрын
these are the coolest thing yet!!
@1mook3 3 ай бұрын
Gonna need some more green accents now.
@stevemullin7472 3 ай бұрын
which intake is that? I cannot find any options for a CAI to the passenger side, once again I will be following your lead on this
@RecycledRacing 3 ай бұрын
That is a 99-06 silverado amazon intake. I used a 4" 90 degree coupler to space it out from the motor some and get around the tensioner. There may be enough room with the boot it came with, I just wanted it to be straighter (OCD) The heat shield was cut up and pieces welded together to make the "box"
@stevemullin7472 3 ай бұрын
@@RecycledRacing terrific. Appreciate your help.
@stevemullin7472 3 ай бұрын
I understand the purpose of the solenoid but wouldn't the breaker eliminate any of the risk associated w/ that 1/0 wire being hot at all time? I'm planning my build and debating if I go with the added complexity of the solenoid. Oh and why did you run a separate 4g wire for the distribution block. Couldn't that have been shared with the alternator feed? Also, thanks for you service 🫡
@RecycledRacing 3 ай бұрын
In terms of function, yes. The breaker would essentially trip if something happened to that wire. I didn't want to worry about it. I have had things happen and damage be done before the breaker tripped. The solenoid removes it from being a constant hot wire. You can't feed to the fuse box from the alternator. When you turn off the car the alternator will keep it running. David freiburger explains this better on roadkill garage on his f-rod wiring video.
@stevemullin7472 3 ай бұрын
@@RecycledRacing I just found the video. His design seems to be related to making sure shut off switch effectively kills the fuse panel. I'm not sure I have that problem in my design. Gives me something to think through though.
@RecycledRacing 3 ай бұрын
@stevemullin7472 I used to run the positive cable up to the starter lug and brach off from there. On two different vehicles, after racing a bunch, the lug rotated and made contact with the starter body. One started a fire. I had one car blow a freeze plug, and the coolant somehow made that electrical connection to short put that line. Only one tripped a breaker. I saw his video, and I really liked not having that wire hot all the time. I still have two hot wires going through the car, but they are smaller and well protected. It's kind of an experience based personal preference. And I usually overkill an area I have issues in.
@stevemullin7472 3 ай бұрын
@@RecycledRacing appreciate the insight. its always good to learn from others challenges so I can avoid them. keep up the great content, I'm really learning a lot.
@tylershipman3377 3 ай бұрын
when wiring up fuel level sensor , one wire goes to the pin 21 for input. does the other wire go to sensor ground on the dash input or chassis ground? thank you
@RecycledRacing 3 ай бұрын
The only way I could get my dash to read accurately was to ground to the sensor ground pin26 I think it was. Even then, it's still slightly off. Since that is a ground circuit, its path has to be from where your sending unit gets it's ground, and go to the holley sensor ground.
@72grabbermav 3 ай бұрын
Your welcome.
@djneil7827 3 ай бұрын
Your approach is sensible. This is almost identical to the work im doing on my GTO . I opted for new inner rockers because I needed to replace the floor braces.. good work!
@RecycledRacing 3 ай бұрын
If I had to do it again, I would have just replaced the entire floor as a whole unit. It would have taken time to remove the old floor, but save me time and have been a much nicer end result.
@gerwin2943 3 ай бұрын
The HMI kit is much better
@RecycledRacing 3 ай бұрын
I think you're referring to the HPI cust9ms kit? I selected the kit I did because it ties the rear suspension pickup points into the frame. None of the other brace kits do that. They tie into the frame just forward of the LCA mounts. But everyone has their favorites. I can say at speed that I have zero body roll or flex, and this car just rotates. Great part of my package.