I have a CVP307 and I have a couple issues with the keyboard. One is the sticky key but after opened the top and looked inside, I found the the stopper felt came unglued causing the hammer hung on the stopper. I cleaned and reglueed and that fixed the issue. My other issue is the lound note when soft press the key. It sounds like you're slamming the key hard. It happened on any instruments on some of the keys from upper part of the keyboard section to the second last G key. I'm wondering if this can be fixed DIY. Kindly appreciate your help or any suggestions Thanks.
@sam.ammatouri3 ай бұрын
Hi @asarnthutube, Yes, the loud note issue can be fixed. But first, check the settings of your piano to ensure that this issue is not a settings issue. Then, if you are sure that it is hardware issue, I believe the problem you are facing is from a faulty group of rubber buttons. In your piano there should be three levels rubber buttons under each piano note key. And these rubber buttons usully come in groups of 11 or 12 notes. So as per your description, mostly one of these groups is faulty. I believe this can be fixed by replacing the group of the faulty buttons. Check this link or find a local store that can send you this: artaudioparts.eu/products/rubber-contact-12keys-for-yamaha-cvp-305-307-309-403-405-407-409-503-505-605-609 By the way, I have also replaced them jn my piano, but unfortunately did not record the process. And I bought them from the same shop I mentioned in the description. Good luck!
@asarnthutube3 ай бұрын
@@sam.ammatouri Thank you for your informative post. Unfortunately, the rubber contact key from the link is out of stock. Do you know if another store might have it? By the way, can the faulty rubber buttons be reconditioned and reuse?
@asarnthutube3 ай бұрын
@@sam.ammatouri Just found one from eBay. Thank you.
@inspirame79798 ай бұрын
How much time did you actually spend before starting the stage 2? We need to solve the loud keys issue on CVP-307 and I'm trying to see how much time it may take us to reach the keyboard and potentially replace the stopper(s) (if the stoppers turn out to be the culprits). Thanks!
@sam.ammatouri8 ай бұрын
Well, I am not sure about the CVP-307, but I believe it is very similar to my piano 305. In my case it took a bit longer time because I was filming and working all alone. However, I can estimate that a person with skilled hands and with some support from another person, the process to reach into taking off the whole keyboard should take 1 to 2 hours, depending on the skills of the technician.
@inspirame79798 ай бұрын
And for someone with some support from another person, both doing it for the first time on such an instrument?
@sam.ammatouri8 ай бұрын
@@inspirame7979 Well, for first timers doing such jobs, I would say no less than 2.5 to 3 hours, given the fact that you need to separate the screws in labelled containers, and to track back the steps, to ensure no mistakes are made.. My advice is to make yourself free for a day for the whole process.
@FoxyJohn8 ай бұрын
There’s another video on KZfaq taking the back off the 307! I have one too and some of my central keys are a bit heavy to press. I think that dropping pad is my issue too.
@sulymanhussain79749 ай бұрын
Nice🎉
@sam.ammatouri9 ай бұрын
Thanks
@user-mo5ns7st5x9 ай бұрын
❤❤❤
@sam.ammatouri9 ай бұрын
Thanks :)
@lahongthang9 ай бұрын
My piano (CVP-505) has the same problem. It makes noise when a key pressed and released. Thanks for your video.
@adnanammatouri879610 ай бұрын
هيك أماكن راقية هيي اللي بتشبهك يا نور عيوني الله يسلم ايديك ويحرسك أغلى ابو كريم الحبيب .
Ótimo vídeo tive o mesmo problema, ago4a mãos a obra. Obrigado pela ajuda😊
@tarkus28 Жыл бұрын
Hi , is it possible to use the tuflUb crc instead of yamaha grease? My yamaha area service doesn't have it. Can you give me a link where to buy the one from yamaha ?