Might be a stupid question but can you run the multi effects pedal plugged straight into a speaker cab and just use the amp effects on the multi effects pedal
@AndrewBanker18 күн бұрын
I’ve setup 3 different input setting for my different guitars. Is there a way to recall them via a midi command, rather than physically changing them on the panel when I change guitars?
@brenolaureano65515 күн бұрын
Amazing ⚡️
@ShenFM21 күн бұрын
Hi there. Id like to pay for an online zoom call with ya. Is this possible?
@juan3m53Ай бұрын
Nice one, sounsds pretty amazing. I just have a question. What's the cable config you used?, I find just connecting the output of the GT into any RC600 instrument input a bit problematic due to output and input levels, but since no send/return present in the RC haven't figured out the proper setup.
@ledhendrix5054Ай бұрын
Maybe you could connect the RC 600 to the GT1000 Send and Return , that way you can move the RC anyway in the GT1000 Effect Chain , would it Record (Loop) all the GT effects before the RC 600 . ?
@juan3m5323 күн бұрын
@@ledhendrix5054 it sounds like the way to go. The only downside is, they only happen in mono so no stereo capability. On the other hand you add control.
@KevinKevin-el8ykАй бұрын
YESS!!YESS! I HAVE JUST GOT TJE AMP SOUND AND IT WAS 10'TIME'S BETTER THAN I EXPECTED THANK YOU FOR YOUR TIME AND HELP FROM ALL OF US YOU HAVE HELPED GOD BLESS YOU'FROM ÈVANGELIST KEVIN☆♡☆♡☆
@KevinKevin-el8ykАй бұрын
EVERYONE LISTEN AND LEARN VERY WELL EXPLAINED AND IT'S GOOD TOO KNOW AND WORK'S BETTER WHEN YOU UNDERSTAND
@fabiorpalombo2 ай бұрын
Great job! 🫡🥇👏🏼👏🏼👏🏼👏🏼
@joewrockg422 ай бұрын
Definitely sharpened my understanding of the PEQ, thanks for the knowledge.
@ramonahallmusic3 ай бұрын
Is there a way to move patches in the order that you want them? Maybe copy the patch to a user setting? I only use about 4 of the preset patches and I would like them in order that I use them. Ie…. Harmony upper & lower, then vocoder, then delay etc?
@larrymyers81783 ай бұрын
First of all, the sounds you are getting out of the GT1000 are some of the best I've heard without a doubt, kudos to you for all the time and effort you put into this. Your tutorial is detailed and comprehensive and will no doubt save me countless hours of trial and error in searching for that sound. I have the GX-100 which is basically the same structure of the GT1000 so everything you have provided will pretty much apply verbatim. Thanks again for sharing this information, I certainly appreciate it very much.
@user-nu3ep5wf6i4 ай бұрын
Is this an old firmware?
@user-nu3ep5wf6i4 ай бұрын
Show the display man
@poetrylines12344 ай бұрын
what is the notch for??😊
@dbajpeyi4 ай бұрын
Can you go Sherrif -> GT1000 with only the cab sim on the GT? That would eliminate the need of two notes. I am considering replacing my OX Stomp with the GT, but I don't want redundant cab sims. But I've also read that it might not be possible to have only the IR/cab blocks without the amp block on GT.
@cthncthn74055 ай бұрын
God, just beautiful. Anyone that snubs GT1000…I don’t know, just seems like a foolish thing to do
@cthncthn74055 ай бұрын
I love that last part with the fuzz, almost sounds like a bug muff. Insane. Thanks for the amazing walkthrough!
@ariefranken5 ай бұрын
Hi, I have an Boss RC-500 looper and try to connect it to my GT-1000 by using Send/return. I put the Send/return as far as possible to the right in the chain. But, when Im playing a backing track on my RC500, and change from amp in the GT-1000, the sound of the backing track is also changing. The amp switch react on the sound of the RC-500. Any thoughts what I do wrong? Cables are from GT-1000 Send 1 to RC-500 A mono In, and from the A/mono OUT RC-500 to the GT-1000 return.
@kitgroovemachine5 ай бұрын
In the mixer, In order to hear the instrument I am playing, I need to set input mix at 120 and loop level at 80, does this sound right ? I will try this tomorrow ...
@GarethThomasTunes5 ай бұрын
Thanks for these videos - it’s difficult to find much online about this nice little Boss unit. One question as I’m about to buy one; are you able to make the vocoder and harmonies play only one assigned pitch? Sometimes called ‘robot’. I will need to do songs where a vocoder robot voice drones on the root note. I can’t see any drone note and drone note settings in the manual. Thanks!
@peterkilgour11355 ай бұрын
I found another way; put a "classic-vibe" with the same settings as the trem but very little depth before the trem
@kevinsalas27165 ай бұрын
Is the Boutique Amp a Fender and Vox stacked together?
@peterflaire5 ай бұрын
Thanks for addressing this issue. Roland/Boss offers very little info on the proper level you should be using to record in. Bottom of page 8 in the manual only shows a vague illustration suggesting where the meter should be. Leaves lots of questions. For example, is that level peak, RMS, or what? I see you used meters on a mixer pre and post RC-600 to get your input levels. However, I wanted to share how I worked this out a different way and got very different results. To start, with no looper connected, I set up my pedal board (which includes a Digitech RP360 digital effects unit) so that master volume had some headroom (up only about 70%) and most importantly, the audible volume when effects were engaged was about the same as when the effects were bypassed. That roughly got me unity gain without the looper involved. Then after connecting the RC-600, I found the line level option on the RC-600 input setup was much lower in audible volume while the inst. level was about the same. That tells me with input set to instr the device is likely working in the neighborhood of -10 dBu for an unbalanced signal, which would be appropriate if plugging into the front end of an amplifier as I do with guitar. Problem with this is despite my attention to unity gain, the input level on the looper is showing me not enough level for recording purposes, and I barely get the meter to register at all. But the question is: Does it really matter? It still sounds great. I hear no evidence of a poor signal to noise ratio. Still, it bugs me that the RC-600 input meters suggest something is wrong. If you know the meters need to be registering somewhere closer to the 100 mark like the manual illustration suggests, please share. I have yet to consult Roland on this.
@feelinthevoid6 ай бұрын
Hi! Is there a way to send ONLY the wet signal to one xlr output? The output mode FX/DRY or FX/Bypass doesn't work: the FX output contains dry signal anyway so the combination of the two xlr output on PA mixer result in a double dry signal that sounds weird..
@tronlady16 ай бұрын
Oh man! WHAT a setup. It’s taking me months just to get my RC600 set up 😂
@tronlady16 ай бұрын
That’s my kinda groove ❤
@tronlady16 ай бұрын
Hearin a soundgarden vibe on this ❤
@tronlady16 ай бұрын
This is quite freaky to be honest. This is EXACTLY the sort of thing I want to do once I get my head round this thing. Are you into Porcupine Tree by any chance?
@tronlady16 ай бұрын
That guitar with the formants is awesome 😮. Are you into prog/psych by any chance? Crimson?
@tronlady16 ай бұрын
Now I know what NS stands for! Thankyou very valuable info ❤
@tronlady16 ай бұрын
Wow. This music is right up my alleyway. Very refreshingly different sir. Sounds uncannily like the stuff I do ❤
@BluesGetOrigin6 ай бұрын
My input level has to be +10db in order to to reach the space you mention at 1:22. Is that normal? I feel thats way too high. This is with my guitar volume at 10 and using bridge pickup
@kevinmejia90656 ай бұрын
That last part really amazed me, sounds beautiful
@PatricioBassman6 ай бұрын
Hello, the information you provide us is great, we learn so much from it. I would like to output to my amplifier and in the sub output give another signal with an amplifier emulation. Do you think this is possible? Thank you so much.
@daniellegiedraitis58976 ай бұрын
Keep coming back to this song really hits different. Gets better and better as the years go on 😍
@Shred_The_Weapon6 ай бұрын
Zed, your charm almost makes me forget that I’m supposed to be paying attention to the tutorial.
@joebowbeer6 ай бұрын
What does frequency knob do when intelligent mode is on?
@nmacog7 ай бұрын
Nice - I had a go also with my JC-22 and pedals, it's on my channel - got quite close too ! Gretsch G5420T-140 Limited Edition Hollow Body Pearl/Stone Platinum ROLAND JC-22 Amp (Reverb and Chorus set to 12 o'clock) 2 delay pedals, one set at 400ms the other 800ms. BOSS BF-3 Flanger BOSS CH-1 Chorus 3rd Dimension Chorus, BOSS SD-1 Overdrive (kicks in after intro)
@RyanChenMusic7 ай бұрын
Boss really should have included a frequency graph on the app to show these edits in realtime!
@gajv107 ай бұрын
Wish I could buy this patch from you bro.. sounding crazy good.. awesome stuff man 👍🏼👍🏼👍🏼👍🏼❤️
@BopKitBill7 ай бұрын
I'm not in front of my unit but as i recall moving the knob makes master and headphone levels change...maybe how one has it configured ? (I kept thinking while you turned the know why is nothing changing...it's not what i remember..... ??
@DreamerOneManBand7 ай бұрын
HOW do I set Volume Level of Individual Patches without affecting all patches ?
@michaelezra92908 ай бұрын
Thanks for the video! Is this patch available for download?
@XISTH8 ай бұрын
Bloody Hell, that is mental 😂. Love that loop too. Do you use midi to sync the drums & bass to the vocoder loop?
@XISTH8 ай бұрын
Just got one of the units, wanna do some lo-fi & radio sounds, really useful video - thanks!
@novanights_8 ай бұрын
Great video! Just got this pedal recently and learned a lot from your video. Just one question, how can you adjust the noise gate?
@vincenzo9958 ай бұрын
Great suggestions! Your channel is always a great source of inspiration.
@user-oy5sy8tg9q9 ай бұрын
Hi! I love those videos? Do you have these patches available to get?
@MrAkifusion9 ай бұрын
EXCELLENT, thank you!!! ❤
@georgwassner94279 ай бұрын
I'm thinking about getting an HX Effect. Is this good for use with Bass instead of building an effect board? All I wanna use are the most important effects such as Octaver, Env. Filter, etc