This was so well explained. Thank you for saving me some money....and scoring a few points with my wife.

I have the Whirlpool WTW4900BW0 washing machine, sounds like a jet plane in the laundry room in the spin…

Thank you! Awesome video! I just fixed!

Nice work

your video is correct. I was told the wrong side of the belt on reddit

So to replace a bad r660a compressor with a 134a compressor. Doyou have to change anything else besides the dryer?

Bad video doesn't show him what he's doing inside

Thank you very much. God bless

I live in Long Beach and need to repair a Samsung fridge. Can you help me out?

Does that upgrade device come with the warranty compressor?

I had this compressor replaced bavk in January the fridge is not cooling the freezer is barely getting cold.a technician just left my house and told me the 3 way valve is clogged and its running high.the compressor is very hot to touch.he quoted me a price of 595 for parts and labor what do u recommend me doing there was a blinking red light on the control board yesterday i pressed the rest botton and it went away any advice i have spending huge amount of money every 6 months on those fridge

thanks for the video

Great video, what is the little clamp called that you added to be able to connect gauges and refrigerant?

Very helpful. Thank you for sharing this KZfaq, and your skills! I almost changed the clutch/transmission ($$$$) or the timer ($$$) but was not certain they were the problem. I did a little further search and found your KZfaq. So glad I did. Changing the lid switch ($) was say following your directions. Thank you again. Bonus: I am golden in the eyes of my wife! woot woot woot!

Model Nr is fking 795🤣🤣🤣

I made the same setup but trying to recover refrigerant compressor keeps locking up and trips the internal breaker. It can do vacuum perfectly goes to 30” and builds pressure over 450 psi. But when trying to recover refrigerant it shuts off.

Thank you so much for the video. great help

thank you very much sir for sharing your knowledge.

Thank you,worked like a champ!

This video was very helpful. After purchasing the lid switch from Amazon I was able to apply the part in less than 15 minutes by following this video step by step.

This video definitely help me I laid my completely over on the side while putting the motor back in

Excellent. Thank you

We have a similar Maytag which can only heat only for a few minutes. By watching your video and others, we are able to fix it by replacing the solenoids. Since it is 30 year old, learning how to replace igniter is very helpful Thanks a lot for your help!

You have a new follower. Great video. This was so helpful in fixing my own washer

Did you have to change the capillary tube or not by chance or you can use the same capillary tube that is use for the 134a

Do you have EPA license, how can you release the refrigerant in the air? It's illegal...................

Thank you so much

Please tell me if compressor is on warranty how long does it take to take old out put new in just labor and parts. What would this cost?😂

A few tips for anyone facing this problem on this fridge. All the screws are 1/4 inch hex The door is attached to the slides with 4 screws. Just loosen them up a turn and the door lifts off the slides, which makes the slides easy to work on If you remove the slide holder on the right hand side, the back panel will bend past the light and you can access the parts on the right side. Three screws hold the slide-holder in place. The light will hold the back out of the way. The fan cover has three tabs. Two near the top that push towards the center, and one on the bottom that pushes up. They're easy to break 😞 Fortunately the thing seems to stay in place with two of them broken. There's a foam baffle running midway across the back facing the coils. If the coils are frozen up, it might get stuck in the ice and break. Fortunately the adhesive is good, so it's easy to reattach the pieces. If you need to get the fridge cold while waiting on the parts to come in, you can judiciously use a heat gun to defrost the coils. You don't even need them completely clear. If you get about 2/3 of the way across then plenty of cold air will flow to the fridge. If there's a lot of ice, the catch pan under the fridge will overflow.

Thank you, any ideas what this service should cost typically?

Gracias este vídeo me sirvió mucho de ayuda

Great video

I wonder why you didn't show what you were doing when you evacuated the existing freon from the system. 🤔🤔

Amazing vid. Helped me all these years later. Thanks!

THANK YOU!! Super excellent, clear and easy to understand, step - by - step repair instruction! Good job! Thank you!

so how is to fix??? this video only how to unscrew/screw back, but nothing related to the fix.

Mmm,I waited to long for you to find that quarter inch. Goodbye!

Trying this on Saturday 6-22-24 Do I have to disconnect the gas?

Thank you for this

hello, would you recommend adding an oil separator to the feed line of the compressor? thanks.

If you hold the switch down it should work correct?

I cant understand a word youre saying

Educational and informative

Helps a lot! Better a restriction than a pin hole leak somewhere in the pipes/tubing! My garage refrigerator stopped cooling! Hopefully the new capacitor/relay will fix it because I wasn’t getting any resistance on the relay when I checked w my multimeter. If that doesn’t fix it than I am afraid this may be the issue! I know my seals are well in tact as well. I may have to get a torch, the correct solder, and 134a refrigerant which is all very expensive!

You need some gromets for the copper lines going thru the toolbox to hold them tight

Thanks! You made it easy.

Thanks Eh! Nailed it!

Hello, I bought a used fridge that was not cooling. I thought it was going to be something simple, but when i open the back the filter dryer is cut in half. Do i need to add a new one?

Where did you buy that part from?

Great video. This saved us a call out so I could fix the top fridge fan. Seeing how to disassemble the entire top unit was a life saver. Thank you!!