whisper mumbling over the sound of a lightsaber.. why even upload this.

❤

Bad idel .. fuel pump ...Air valve. ...dirty choke. ..fuel regulator... fuel pressure ... soark plugs... leads. .. check all. My idels low xar sgaje and miss fires....hesitation issue got be fuel ? Pump ?

Need to put relay in check pressure fuel ta

Which firmware is that, mine doesn't seem to have the same options?

1:04 1:06

Is it possible to have this set up, with a variable temperature setting (off a graph over time for baking/roasting) assuming the temp sensor is an infrared heat sensor

Hi,I'm not sure if you can help me ,are this parts still available

Hello brother I have one project can you help? I need to build autoregulator of temperature

Can this will automatically turn off the temperature for the water really high? 😊

the temperature and humidity is only showing 0. how do i fix this?

can we apply this idea in drying rice grains in a small acrylic chamber?

Great video, the million dollar question it worth it?

Tx to Rx and vice versa.... Correct that info.

This is more of a work-around, not a solution for resetting the Z-axis.

Hello, recently my Cr10S Pro V2 got stuck on the load screen and while looking for a solution I found this video, I followed the instructions and did the tiny machines upgrade. It did flash the screen and it fully loaded. However, now my touch screen is unresponsive. Oddly it would work some time perfectly, then I would have to hold my finger for a few moments then it it would respond and then more time than not it would not respond at all. I then found the factory flash setting on the Creality website and restored it to the original. It did come on but responded the same so I then went back to the tiny machines files but still not responsive. Could this actually be a touch screen problem or do I not have the right flash files? Or do you think this option would work. Any help would be greatly appreciated!

Totally wrong procedure. Watch the many videos avilable to manually and clever level the bed once forever, then to find the ZERO Z axis position (nozzle must sligtly touch thebed surface), then to save the mexh profile of your bed. By doing so you can then make a lot of printings without to run auto levelling and without to have to modify the bed levelling. After a long while the bed undergoes to sligth deformations and you have to redo the entire process, but it takes a long while prior to have to redo it.

Thqt is the sound of a TRUE vehicle

Where we can find these components please help me

Bonjour j'aime votre métier si vous pouvez m'envoyer votre adresse comple et électronique je suis en RDC

Hi bro thank you so much for this, please help me when i press the down button and reach 09 it shows 99 and then 88 and 77 and so on how can i rectify this please help thanks a ton

❤well explain

Boss ano pangalan mo sa fb

Does not work!

Hello! If you are still looking for work, I have an Arduino project I need a consultation on. How do I contact you?

anyone have an issue where bl touch is now sitting too high and won't make contact?

code of this please

its works for creality cr10spro ? do you have any information about that ? I need it a firmware and lcd driver, because its not working , thanks !

Can i know wt the value of an resistor

Hola amigo como estas. Te consulto? Limpie los picos de mí camioneta lleve igual al del vídeo. Estaba re tapado es 2004 y debe que nunca lo limpiaron. Ise las pruebas y rosia los cuatro rosia bien solo que no arranca más la camioneta. Un error que vi q mí amigo realiso que puso el pico del compresor con gasoil donde va instalado los pico y le dio soplete para limpiar, capas le abra apagado. Que me desido Aguardo tu respuesta saludos de antemano y gracias

Can someone send me the link for Nic Wilson's firmware?

Hello how are you .Please can you say me instructions which can i install Bosch pump into engine .thank you .

I downloaded the firmware and Dwin folder from his site and it kind of worked. I turned my temperature to 287C it caped out at 272C and above that it stopped with Temp run away. I changed the temp probe and 40W heater and still stopped at 227C. I tried to connect my laptop to the printer for Ponterface to test PID values as his software wouldn't do them. I then searched the web again and Tiny Machines offered the software and hex file. When loaded The TM3 files everything worked perfectly. Temperature now goes to 287°C and Ponterface did the PID test and the printer PID test with the new software had nearly the same values. So I would search again and find instruction files on Tiny Machines website.

Is there possible we can add the turbo boost compensator on all bosh inline pumps

Looks like the dephi for 1.5 dci but there bigger though very informative great vid

Hey, I have a question: My top 2 delivery valves arent getting through any diesel. What could be the cause?

I am putting a VE pump on a 2002 24V farm Truck. I saw online where I should advance the timing 2 teeth on the pump gear is this correct?

Hey how did u like the board? I got it years ago, thinking about still using it

With blessing!!! To Jesus with Maria

How would you recommend adding a timer to the relay on command?

Great video, thank you What does the Validate Mesh button do in the 5 point grid auxiliary level screen?

Good night best friend you I am working kas

Hello dear my magnet reads out 1.3 ohm when it cold ... so is that faulty ?

8mm off center? Thats a lot. How did you fix that in the firmware?

could you please post the wiring diagram clearly?

Good demo. Good job.

I read through so many forms to try and fix this issue and was wondering if I could just use a skirt like I always do as well and you confirmed it. Thank you so much. That damn triangle was pissing me off!

Nice one Best wishes 🛠️🚜

After flashing with this firmware my auto level option won't turn on. It only stays on off. Please help!

Great post and printed the files as preparation for my Microswiss DD upgrade. Question however is how did you mount the fan duct to the fan shroud? Not very clear for me. Appreciate your answer.