Hope you are well

If I want to make rounds that have low report, and lower recoil, do you just use 1/2 of the scoop dipper? Or is that a bad idea? One reason I’d like to make bullets is low report, recoil.

a man of few words. thx

Fortune Cookie 45, has a few crimp videos.

Interesting that tape slightly adjusted sights.

Thanks again.

Excellent, thank you.

Works great! kzfaq.infoUgkxprGGPRQoChQaA8u58dt7miEpxQBKiWeJ More difficult with longer grass, though, but I was expecting that. I have a small back yard, it seemed like overkill to buy a lawnmower with an engine. This is easy to carry in and out of the basement through the bulkhead. Very sharp (be careful). At the back of the mower are little wheels, which I use when pulling the mower backwards, so it's easy to readjust direction. I'm including a photo which shows the before and after for my lawn when it was at its longest. For long grass like that you really have to put some muscle into it, and I needed to go into a new section of grass with some momentum, but when the grass is only an inch or two higher than regular cut height it's quite easy. The lawn is still patchy and full of weeds, but at least it's a good height! A step in the right direction.

Works great! kzfaq.infoUgkxprGGPRQoChQaA8u58dt7miEpxQBKiWeJ More difficult with longer grass, though, but I was expecting that. I have a small back yard, it seemed like overkill to buy a lawnmower with an engine. This is easy to carry in and out of the basement through the bulkhead. Very sharp (be careful). At the back of the mower are little wheels, which I use when pulling the mower backwards, so it's easy to readjust direction. I'm including a photo which shows the before and after for my lawn when it was at its longest. For long grass like that you really have to put some muscle into it, and I needed to go into a new section of grass with some momentum, but when the grass is only an inch or two higher than regular cut height it's quite easy. The lawn is still patchy and full of weeds, but at least it's a good height! A step in the right direction.

nice! thanks for the tip

Idiot

Tape? Really?

Can you help me. I have the same mower as you but I want to lower the week for a shorter cut. I can’t for the life of me get it to lower 😅

Just what I needed to know: tightening the bolts closest to the rotating blades pushes the cutting bar away; tightening the bolts further away pushes it closer.

Ya don't need that crank buddy. Just switch the wheel gears and push the mower around, does great sharpening. Then switch them back afterwards.

Hi Nick ! St. louis Hillbilly here. EXCELLENT

At the beginning you made the tension between the reel and the cutter blade more snug. Do you readjust it back to its original position at the end? You left it tight

Neat, great video!

I bought some bright orange fingernail polish for mine works great so far .

you have to drive the case all the way into the resizer. that case was not completely resized. this is way you don't watch some dipshit on youtube thats just trying to get views

Painting my 605 sights would go a long way to improving my accuracy, thx for the tip!

I would be very nervous hammering on that bullet, but imma get me one of these before it’s too late.

Birchwood casey has flurecent paint pens just for this

Womens Red fingernail polish.... can be removed with polish removerr.....if needed. Crack Wh@re RED... super bright.

It’s not safe to use that in your pipe

I found a small bottle of model or hobby paint in lime green. It works pretty well.

Likes to you

Good thing you can use a 11 mm because I can’t find my 10 mm.

Ur the best! Mower was cutting too short. Killing my lawn. Didn't know how to adjust it. Ur explanation was easy to follow. Thank u! My grass thanks u too!

Thank you

Great video he is absolutely correct about the distance of the blades you absolutely do not need to cut paper for it to work properly

you want to turn the blades backwards

Amaretto works great and other liqueurs cut with 50% grain alcohol/ Everclear

I got a well worn reel mower for free. The blade edges were worn and pitted. To sharpen it would need to take off one millimeter of metal. It would take too much effort to use backlapping method. So I use a mill file to shape the bevel to small angle and horn the edge with 1000 grade stone, and convert the mower to non-contact type. I lubricate the ball bearings on both side of reel shaft. Now the reel rotates at high speed and cut grass with speed like weed trimmer.

Buy a pipe! Pipe smoking is forever !! ALEX from Royersford PA

I purchased my Kel-Tec p32 brand new back in 2003 generation 1.. it functions flawlessly and I can hit targets out to about 40-45 ft which is perfect I purchased the clip from Kel-Tec and can carry it in the waistband of my BVDs as my underwear gun... I also carry this in a DeSantis Nemesis pocket holster when I wear lightweight dress slacks.... WARNING.. 32 ACP is semi-rimmed and if you carry hollow points you can have rim lock issues... Either just carry FMJ.. hardball..or you can purchase anti - rim lock kits.. from Kel-Tec install them in your magazines you can then safely carry hollow points without any rim lock issues... Frankly fmjs have much better penetration I would just stick with those

Very Good Explanation , But How many milimiters do you recomend the distance the Reel mowner to the Bar-Knife??

Aromatics smoke hot 🔥 🥵 I like dark flakes they smoke cooler 😎 😋

Do you full up the scooper to its brim?

2:12...thanks!

Thank you for this simple, straight to the point, self explanatory video. Thumbs up to you, sir. I like the overalls. :)

Mine dont move its new

If you're going to forward lap, then why bother taking a wheel off at all?...Just put the grinding compound on and push it around a bit...

The whole point of attaching the hand crank is so you can spin the blade backwards (Back lapping)....you cranked it forwards in the video.

Dirty reels dirty wheels - check Nice mowed lawn - check On point beard - check Flannel shirt - check Nick Offerman Voice- check Rating - Expert instruction Thanks for the vid!

I like the way you think....ready for next year!

Your demonstration is the best I've watched, I think I might be able to do it now. Except. Yesterday I ordered a new reel mower. It's ok, I'll use the new one while I destroy the old ones (yes, I have four) trying to fix them. :(

Comes from shooting 38 special in the longer 357 cylider as well. That also causes a buildup line in each bullet housing

thank you. how long should i crank it to sharpen?

Good explanation... thank you!