Hittade felet på min fågel i dag efter flera dagars felsökning, ny regulator beställd

What store did you get the 3/4-16X3 3 inch long bolt from?

1985 unit

Thank you Brad! This middle-aged lady was able to install both front wiper blades because of this video. In under 2 minutes!!! Great job showing the packages with the part numbers and explaining and demo’ing it all so clearly. 😊🙌

Great hack. Thanks!

to long buddy only have one idler pully

How often do you have to change your tire oil?

question for you, i have owned my 2003 since brand new and mine is having a slight stumble off idle and some slight erratic idling. I was pretty sure this was my issue but when i primed the system it looked perfect, not a drop came out. The bike has 8700 and was babied. The only thing i can think of is i had a battery die out just recently and being i put the battery in backwards....well i put it in forwards, it supposed to go in reverse and crossed the terminal. It did blow the 30amp fuse but now i'm wondering if that is an issue. Everything works fine, the bike runs excellent otherwise into the higher RPMs......just maybe a slight hiccup around 2500 rpm and intermittent weird idle. (not crazy but sometimes fluxuates around 1200-1500. Any thing to check?

Thanks for this, I got my 95' 300 explorer about half apart, just enough to expose the front portion of the starter and the starter isn't even engaged with the gears on the shaft. It also wiggles around, I'm no expert, but I'm guessing that means it's worn out. Anyways, now I have to take off the second half and get her out. There's quite a few steps, I'd have been shaking my head and probably throwing a wrench or 2 had I not seen this, so thanks again!

Thanks for the video. I spent some time figuring out how to replace it so many thanks for saving me time and effort 🙂

Good video other than that

I really wish you would have shown me which way to wind it up

Doesn’t work on the 2022. What a stupid feature

This procedure won't work with 5th gen 2021 1500!

Thanks for the video and I was wondering I have the one you showed, does the belt have a lot of play or is it snug ?

What size and thread pitch bolt for the puller??

Used this for a rebuild in 2024. This video walked me through bringing this old girl back. Ron Ritter sells a rebuild kit and it runs 10/10 now. Thanks!!

I have a 95 300 two stroke air cooled but I can't get a torque wrench in to torque the cylinder nuts any ideas?

How does the axel stay put?? My axel came out? Is there a locking system that keeps it in the diff?

ty great video

I have a question can someone answer? If doing it this way, does the 4 wheel drive system still stay energized regardless if the 4 wheel drive switch is turned on or off? Wouldn't you need to install a cheap on/off toggle switch inbetween?

Maneral palanca velocidades manual de cuatri honda 500 4x4

50% stiffer, yahhhh buddy!🤟🏻

Great video Thanks for recording

$85? Where did you get that? I check can am site and one went for $400

Shoulda towed Tim around on the big wheel!

1:18 "Hey, no swearing." 😇

How do you reset the system after getting new tires on?

Sway bar removal necesary?

Geez what happened to that thing

Excellent video. Thank you.

I think I lost my seal... My Walker has been spewing oil all over the exhaust manifold and muffler... I stuck my finger in alongside the crank shaft, and it went in a good ways. Didn't feel any kind of seal... Really hope I can do this without yanking the engine.

Does doing this effect ride height. I’ve got 1.5 inch level in the rear, and want stiffer shocks but the same level look. Thanks for help

Awesome. Thank you!

Dope video bro do you know if a bad regulator can keep bike from starting?

Ummm. Go to store and by hex wrench socket with extended hex. Not sure the torque applied here is accurate. Unless accuracy is not your goal, then German torque, gudentite, will do.

What tab.

I will try this right away and if this works will save me so much trouble.

I'm installing these tomorrow with 2" spacers and Fox 2.0 shocks. Then Bilstein 5100 lifted coilovers in the front with JBA UCAs

How long did these bearings last you lol

Thank you! Straightforward and easy to follow!

What is the point of the dinosaur?

Not the first time I've seen those circuit breakers go bad and have rust on them.

Haha well done I'm gonna do mine now.

Next video….4 corner cold score on all my sleds…disgusting dude!get a clue…never rev a cold engine

You guys made my job A LOT easier. Thank you. I definitely need to do my rear shocks, Im having a lot of body roll on highways. I just hit 200k, so I definitely need a shock upgrade on my 2012 Ram 1500 Laramie.

This video saved my ass. 👍

if bendix is ok, should the starter just slide in and out from this side, mine seems stuck pretty tite , thanks for the video

Do you have a way for me to contact you? I have a starter issue and I'm completely mechanically inclined

Excellent video. Saved me a ton of time. Great details