We did ours last year , hope u used better 6x6 than we did already twisted so badly that we have to do it again

How does it keep it down for a right snug fit

Id like to see them screws "into those holes.

What a great video, thanks!

Both my angle irons front and back are welded in

Your dust free tool storage is the first one I have seen on KZfaq, Thank you for your ideas, it is inspiring.

Have tried many times to click on links for plans for outfeed table. An table with jay bates router lift but it goes to a blog about washing tennis shoes. I can go to just jay bates router lift an that works ok. Must be prob. In system. I am interested in plans also tried to find out where u bought pure bond ply an couldn't find listing?

So the pin doesn't go all the way through what you're cutting?

Recommendation for drilling on trailers that DONT have bolts already? 1 hour in.. 4 broken bits. Not one complete hole

Have you ever used Just two end boards ? I kinda want to use the two Headboards for a day bed.ihave two twin beds.

I was told wood cannot touch concrete because it can dry rot. You need a footer underneath.

Your links aren't working!!

Were there any screws besides the end caps that you re-installed? I'm getting ready to do this on my trailer. Thanks.

How about stepping back and get a photo from a distance

Now that's a bench I'd trust to sit on, not like some of the flimsy fast things posted. Thanks for not spraying with cheap and unprepped paint job, too.

Love the jig! All of it really. Thanks building some storm shutters w pallet wood I’m cutting up and the video was helpful!

That color explodes. That wood with brass hardware wood make great cabinets.

Do you have to space the oards? Or can you have no space between? thanks

I'm curious about that garage door. Is it 10 x 8? It actually looks smaller. I have been looking for a new 10x8 or at least some descent simple panels. But it's such a freak size these days either n/a or what they have is such a limited supply of designs that don't appeal. I just want simple flat surface, no windows. My door is probably the same age as me. The bottom panel rotted out because it was made like a lot of stuff in the seventies, thin veneer and an inner core of cardboard. That's basically ok here in South Alabama, but the garage floor extending through to the outside was pitched back toward the house. So yeah standing water rotted the sucker. I need a metal replacement. Any info you can pass to a fella would be greatly appreciated...BTW nice work there on the cart!

You mention securing the board’s underneath the trailer. Is there a video on those? Thx

The author does like to from scratch, kzfaq.infoUgkxbnOKZBE4evMO5V2vroHeCjq6d_MV6wJO shaping and trimming wood from large blocks into fine finished products. As another reviewer mentioned, most projects require a lot of high-dollar equipment that most of us don’t have the room or budget for. But, knowing how to do these things, even if we won’t be able to practise the full stack project, is still great.

Thanks for showing an old man how it is done.

6:42 thank you for this video. I have the exact planer. I put my collector together using your friction fit method and the existing accessory screw holes. Awesome!

Your site is not working.. I tried to access it, and nothing. is it still working? In fact, Bluehost pops up and wants to sell me your name.

You should never space new boards.

Color of Stain?

Bad ass!

Should have just cut bolts off lol working way to hard.

The link to the plans wil not load?

This is just an amazing story, thank you for sharing. Go after your dreams!!!

Did the torx screws come out easily :12-16 second mark. And did you screw the boards back into the frame?

Put a liberal amount of Boiled Linseed Oil every 6 months and the wood on that trailer would last forever…

Where do you find wood that straight?

How deep in the brick did you drive the threaded rebar?

How did the gap work out after the new boards dried I have read different opinion in regards to spacing new wet pressure treated boards for my 5x8 utility trailer.

*Great! I really enjoy watching your video!👍👌🤝🙏💪*

EXACTLY what I’m looking for, awesome!

Miss this channel, wish he still posted

I used my reciprocating saw and just cut off the bolt heads

very cool piece. Nice video style as well.

I always wonder why people say they "Went ahead and did it" or they're going to "Go ahead and do it". Where did they go? Hey Cisco...I theenk it's time to went!

Question: my trailer has 2 rows of additional fasteners along braces a couple of feet fore and aft of the mid brace. Did you just decide the additional fasteners were unnecessary?

What size boards did you use? I have 1x6 I would like to go up 2x10 Will it work?

Nice piece.

Thank you, my dad passed away recently and left a run down trailer that needed replaced. That info was just what I needed. Thanks again

Amazing! Well done. This looks like something you’d pay $200-$300 for. Thanks so much!

What kind of lumber?

Not a "Stone" left unturned when collecting dust in this shop.

hope you are doing well Shawn

I just watched this video. Could you update the project by doing the same thing, instead of a bench and make a chair from a single person bed…???