I was thinking this is pretty cool until you said drill concrete without the hammer. WTF. Concrete doesn’t crack with the hammer function. It’s obviously not concrete that is capable of standing upright for the next 100 years.
@velocitymgАй бұрын
Do you need to do this for every socket and outlet required. What about internet, phone, smart home wiring. Then there’s water, floor heating, gas as well to go in and the rippling makes it difficult to fasten anything down. 3d printing seems to be an answer to a question nobody really asked for or researched properly.
@krich79772 ай бұрын
Lol.... Your electric install just skyrocketed... One the more costly professions on the job, far as time/money. 3ksqft home around 15-20k most areas. This would effectively 2-4x my work load on a home. You pay me for expertise, not so much labor. But the labor doesn't drop if I'm doing general labor. I'd move from bid from 15k-20k to 30-35k, if not more. Unless your going to drill all the holes correctly. Its licensed permit work required, is no Joe blow to replace with for cheap. -electrian
@martinXY3 ай бұрын
If my drill's battery pack is dead, can I use a sledge hammer?
@JustSayN2O3 ай бұрын
You can also use your finger to write your name into the wall, after flattening a part of it. "JSN 2024"
@user-jq6yo4ki5t3 ай бұрын
My dear friend, what is the treatment for cracks?
@scott5927 күн бұрын
Probably same Mortar as its made from.
@JustSayN2O3 ай бұрын
I recommend building a very sturdy table that holds the drill on an advancing platform (similar to a drawer but incredibly sturdy), so the hole cutter is not wobbling around during wall insertion. The table/drill setup can be set to outlet height, light switch height, and wall-mounted TV outlet and cable termination height.
@user-wz1tv2ro1x5 ай бұрын
Contect no Kay ha
@gorsignups7 ай бұрын
I mean, in 'traditional' 3d printing, we use supports that are removed later. Fancier printer setups have two nozzles; the 2nd sometimes used for just support. Watching these concrete printers, it seems that just putting a square box, if not an actual electrical outlet box frame, on the last printed layer would only require 'cleanup' with a trowel in that area, since the concrete would 'blob' around the box.
@justanotherhuman18657 ай бұрын
How much in total and by what metric analysis does this save costs in constructing and also the sale of the home?
@user-qx1wl2um2k8 ай бұрын
Pure trash. Sorry.
@techiejam8 ай бұрын
The crown without drill bit?
@curtokay80468 ай бұрын
how much diesel does it cost ?
@CyBeConstruction8 ай бұрын
Hey, At CyBe, we're all about sustainability. That's why our printers work on energy. Our plug-and-play machines do not require any petrol. Hope this helps!
@teslastones8 ай бұрын
It doesn’t
@teslastones6 ай бұрын
So called 3D printing solves a non-existent problem while creating a hundred unnecessary new ones
@pt-dz8rm9 ай бұрын
Really , don't use hammer feature?? that's what it's designed for,. if this 3d wall is that brital.. DO NOT PURCHSE THE NEW TECH GARBAGE
@RR-sb8tm9 ай бұрын
Expected: electric sockets are printed as part of the wall. Reality: take a diamond drill...
@MilosKucera9 ай бұрын
again excellent 🙂
@RKOuttathebox9 ай бұрын
Are all the walls hollow? Someone in another comment section said they are filled with concrete and the 3D printed part is more of a concrete form.
@yzorgone9 ай бұрын
those shapes can eaily be made by hand. and much much faster. use that printer for something more complex. its a waste of machinery.
@CyBeConstruction9 ай бұрын
Hey @yzorgone, thanks for your comment! To address your concerns: this print was done as training for the team from Seaboost, to get them acquainted with the machinery. In the last week of their training, the team managed to print as many as 34, more complex reef elements in a 1-hour print - much faster than would be possible by hand! Eager to learn more about their training? Check out cybe.eu/training-seaboost/!
@raphael933910 ай бұрын
What is the insulation?
@rktho202010 ай бұрын
Hello im also working 3d printing house
@mjm302210 ай бұрын
This idea will work in my country I invite you to ours
@moss870210 ай бұрын
There's some contractors using one of your machines without dusting off the slab (or flat out leaving mud on it to be printed over) and having concerning overhang
@drumswest503510 ай бұрын
Looks like the cost of electrical and plumbing will be high. Wonder how they water proof the exterior of the walls, concrete is very porous.
@user-zc1pq4xr2p10 ай бұрын
Brilliant technology.
@helenmiddleton2431010 ай бұрын
Beautiful!😍
@JJones-cl4dm11 ай бұрын
Very been an electrician for 25 years and all I can say is what a nightmare having to hole saw everything into concrete! And how is that bx supposed to stay put I could walk up and yank that out
@VersinKettorix10 ай бұрын
It appears that a different kind of box structure will be needed. Something that has extendable flanges on front and back or something else to secure the boxes. Is PVC rated for electrical runs? I thought steel conduit had to be used.
@yga37439 ай бұрын
Yea tell em jon
@bertbaker70678 ай бұрын
To be fair, you could walk up and yank out most remodel boxes, but I hear ya. Where I work we have two big hammer drills for 7 trucks, if these became common place we'd, at the very least, have to make sure every truck had a 8 amp drill
@andrewfreeman887 ай бұрын
The face plate probably has a couple holes for some anchor screws but yeah not much.
@Abhishek-Kumar331 Жыл бұрын
👍👍
@ezdeezytube Жыл бұрын
How about the plumbing?
@doctorjoey3 Жыл бұрын
I'm not convinced . WHERE is this being done In Florida ? Thanks
@CyBeConstruction Жыл бұрын
Dear Joey, unfortunately, we cannot share the exact location of the construction site. The project is being done for the private housing sector, and sharing its location would result in too much unwanted attention, as well as too many people visiting the construction site. If you are not convinced, please visit cybe.eu/cybe-constructions-first-3d-concrete-villa-in-florida/ for more information! Thank you for you understanding, CyBe
@leonmilner9994 Жыл бұрын
Good stuff!
@raterus Жыл бұрын
Simple?
@robertschaaf71928 ай бұрын
nightmare
@gksmfwlstjr Жыл бұрын
How much printing time gap it was ??
@djwashx2 жыл бұрын
Congrats I would love to run 10 of these in the usa