Worst video I’ve ever seen 🤦🏻 time wasted I will never get back 👎🏽🤨
@deloraharden553819 сағат бұрын
Nice. I'm from Los Angeles CA
@user-kb3wf7xv3q20 сағат бұрын
Hepsini ayrı ayrı cok beğendim ELİNE GONLUNE sağlık selamlar
@kaedre121120 сағат бұрын
So, not only do you have to have all the right tools, but you gotta Damn near be a Chemist as well 🤷🏽♂️
@robertgraham162620 сағат бұрын
Who is the ,Chick,doing these videos?
@oferspivak20 сағат бұрын
Hello from Poland
@stefanomonetta792622 сағат бұрын
Ho il camper e ho problemi con l'antenna ho bisogno di un fai da te ti ringrazio
@stefanomonetta792622 сағат бұрын
Sono di Salerno Italia grazie
@travisleonhart337123 сағат бұрын
Can you imagine the creativity required to find this type of shhh
@arrudaum23 сағат бұрын
Awesome, my dad saw this video and went off to buy some cigars. I hope he comes back soon.
@user-xy5wu6lo9pКүн бұрын
Пружину надо в стакан с водой , тогда ещё и чай заварить получается
@antonianicola6457Күн бұрын
😅Romania
@SandorCserhatiКүн бұрын
Ez úgy marhaság ahogy van!
@Mr.ghanbariGhanbariКүн бұрын
عالی بود
@florrianzsiga5216Күн бұрын
the 12.32 minute for plastic grinding is not useful, it was better said
@walter6574Күн бұрын
Poor soldering technique. People who don't know how to solder bring the solder to iron, let it melt and then bring it to the point where the soldering needs to happen. That burns the flux away. Solder without flux will not give a good permanent soldering connection. Just saying.
@tarciliobeneditodasilvafil3921Күн бұрын
Você já fez coisa melhor, mais essa não ficou ruim, sou do Brazil e você ?
@martinkulizaКүн бұрын
The last one was silly 1. No one is going to do that 2. if the needle gets unhitched that could really hurt and be really dangerous
@martinkulizaКүн бұрын
1/6 why did you need to take the OTHER top one off ? that seemed to serve no purpose
@DieterKostynskiКүн бұрын
Ich bin begeistert!
@ItsMzPhoenixКүн бұрын
How safe is this from a food safety perspective?
@user-hm2yr5eb2cКүн бұрын
наглядный пример как не надо делать.я бы этому мастеру руки оторвал.переделка потом выходит намного дороже
@pushkargupta2284Күн бұрын
Dhil dhilmanai
@anthropoidchannelКүн бұрын
Відео - хуйня, головне це назва...
@akadcp82Күн бұрын
What wattage soldering iron do you use?
@inanbasar1Күн бұрын
Muhteşem
@prof.thonyveras4627Күн бұрын
São Luís MA: Brasil
@inekelassooij840Күн бұрын
Geweldig gedaan top job groetjes uit Holland 👋🏼🇳🇱
@AngelRodriguez-fv7ocКүн бұрын
Eso está fino. De calidad y sencillo. Gracias. Angel vzla.
@adailsongoncalvesdearaujoa8455Күн бұрын
FICOU BOA NAO
@atlchaiКүн бұрын
Would you please show how to repair TPE sex doll. Thank you. ❤🎉
@moemaster1966Күн бұрын
Another excuse not to stop smoking? Think again 😂
@Flachrelais48Күн бұрын
Kupfer und Aluminium niemals direkt verbinden. Das hält bestimmt nicht lange! Dann doch lieber original Adernhülsen verwenden.
@anonymously241Күн бұрын
What is the top speed? 🛵
@martremcheerfulfulКүн бұрын
I knew it would be a load of crap
@yonifabri1085Күн бұрын
Surabaya,indonesia👍🥰🕋
@IlIllllIlIlКүн бұрын
South korea🎉
@ELGERGAWYMohamedAnwarКүн бұрын
The Egyptian Arabic Republic
@lackodhr.5303Күн бұрын
🤗👍👌💯
@user-dv7hb2sc9mКүн бұрын
Yeah & this piece looks like a motorcycle/scooter part, they have lots of "plastics" on them nowadays so this can save you a lot of money. Replacing plastics off your bike is really costly. So expensive that many will take all the original plastics off their bike to wrap them/store them, they buy another set of them knowing they will drop the bike or wreck & this is far cheaper than destroying the original plastics. Also, I like this for repairing the "dash" inside cars/trucks. Some older models don't have replacement stuff available so this is the best option...... peace
@alexandraseitlinger8366Күн бұрын
It wasn't the best job, but it's acceptable
@taxitoon119Күн бұрын
solt and water ?
@user-ei6np8yj1iКүн бұрын
แบ่งปันเลิฟไทยแลนด์🇹🇭❤️❤️❤️
@fransjebik8554Күн бұрын
Thanks! I will try to do the same with my old rainwater barrels! 🎉
@CreationNOY80Күн бұрын
Your idea is wonderful, Thank you for showing it to everyone.
@hongtrungao8917Күн бұрын
Bạn khéo tay hay làm đầy sáng tạo ❤😅
@DIYLINUXКүн бұрын
Very good way to repair plastic. It helps us save money by not having to buy new ones. Thank you for sharing the video.
@kayak9549Күн бұрын
Кнопка понравилась!
@DIYCreativeTrends100KSubКүн бұрын
wow the video is so helpful, i really like this trick