It sounds just like a 590 basically the same except the engine
@iamaparanoidandroid14 ай бұрын
Am i right in thinking that the hitch can be slid forward to another location so that it sticks out less? Our 1959 has an original one which I dont want to lose but its in the way of something im building for the 3 point linkage.
@OliverLee3904 ай бұрын
You can take a pin out at the back and slide the drawbar piece out and leave the carrier on the tractor, which leaves plenty of room to fit anything on the linkage
@bl45655 ай бұрын
Nice to hear.. Best regards J.
@bl45655 ай бұрын
Nice it Works Good and fast.. Looks good.. It is a Nice Finger cutter and tractor.. best regards J.
@bl45655 ай бұрын
Nice Short Video make a Longer Video Please.. It sounds great.. Can you run them 1 by 1 at Lowest Possible Idle It sounds so Great Best Regards J.
@OliverLee3905 ай бұрын
They're both set at the idle they run the best at, thanks for your comment
@RJ-xv1nh6 ай бұрын
I have a 203, great machine. Even better for putting JCB3c wheels on it
@dafyddmorris-si7lt7 ай бұрын
We had a 203x and if the pump is on the front ,make sure the front axle bush is good, because if theres play you will eat pumps and the shafts that screw in to the axle, also the thing infront of the front levers is the breather
@stunnicliffe17 ай бұрын
My dad had one of those with a grey Massey Ferguson tractor.
@smalldairyfarmer9 ай бұрын
#ifarmwefarm restored a ferguson T20 just came across yours great channel 👏
It sure seems to do a good job fluffing the hay back up for air circulation.
@paulancill3872 Жыл бұрын
Do you want to sell the rams?
@OliverLee390 Жыл бұрын
Not really, could be handy as spares for my other 3165 digger
@alandigweed8713 Жыл бұрын
real farming. I drove a similar combination on Sussex farms many years ago
@davidperry9954 Жыл бұрын
Yea that takes me back when I was a teenager working on a farm I mowed acres with one of those they were good day's you're tractor and finger mower do you proud 👍👍👍
@paulthompson8467 Жыл бұрын
Good video your fingerbar mower is cutting very well tidy job the 35 looks class👍
@OliverLee390 Жыл бұрын
Cuts far better than any topper would and fast regrowth I find too
@paulthompson8467 Жыл бұрын
@@OliverLee390 definitely our topper only batters the grass
@thebluehouseboys3935 Жыл бұрын
I'm on the same Facebook group and saw that photo and nearly cried
@Johndonvan861 Жыл бұрын
Why are u chain harrowing grass like that?
@OliverLee390 Жыл бұрын
It’s how we’ve always done it, old fashioned way of doing it but works well for levelling the muck
@Johndonvan861 Жыл бұрын
@@OliverLee390 aww yes I did hear off that before now as you mention it, sure if it works I woulded worry about being old fashioned, it just might be abit sore on the grass
@crispinaske8293 Жыл бұрын
@@Johndonvan861 You cannot be too hard on old grass, not only spreads the dung but rakes out old dead growth and aerates the sward.
@fredbaker3822 Жыл бұрын
nice video olie,👍 ive done all mine as well. Are you doing spuds this year?
@OliverLee390 Жыл бұрын
No haven't done spuds in a couple years now
@vehicle_entrance Жыл бұрын
Good video. It's nice to see them being used and working
@paulthompson8467 Жыл бұрын
Wee fergie is running very well 👍
@ClarenceFudWeasel Жыл бұрын
You never said you had your own channel. Great piece of work.
@OliverLee390 Жыл бұрын
Thank you very much, more to come soon 👍
@ClarenceFudWeasel Жыл бұрын
@@OliverLee390 look forward to seeing it.
@willharris8324 Жыл бұрын
Quite a project you've got there. A friend of mine has a 3165S as well. Was fitted with a hedge trimmer when he bought it and had been used for hedge cutting on the railways for Dingle Brothers near Bodmin in Cornwall.
@deranocasper Жыл бұрын
Brilliant all the best for the restoration
@TylerRead12 Жыл бұрын
thanks this video saved me
@mechanicalmoron2251 Жыл бұрын
at least the 390 dose not mark its territory as mutch as my Landy
@bluethru808 Жыл бұрын
Like seeing the diggers 👍 fair amount of work there, but be worth it in the end.
@Johndonvan861 Жыл бұрын
She's slow tipping the trailor, never the less isnt the power off hydraulic wonderful
@OliverLee390 Жыл бұрын
Yeah, main reason it was so slow is I had the quadrant set up wrong
@cesarfarias4219 Жыл бұрын
Bom 👍
@trevorwood2219 Жыл бұрын
Is that a tvo 35?
@OliverLee390 Жыл бұрын
Yeah, great little tractor
@trevorwood2219 Жыл бұрын
Lovely sight,used all of them,wuffler was a good tool,only got ousted because bigger two machines like the cock pheasant became popular,oddly they did make a two row wuffler but never bacame popular
@Valmetinho-180_2.0OFC Жыл бұрын
Diesel or gás
@OliverLee390 Жыл бұрын
TVO, in other words kerosene and petrol
@veteranmaskiner5908 Жыл бұрын
I have changed the head gasket on my ferguson goldbelly with petrol engine. But the engine became much heavier to pull around than before. I tightened the nuts for the cylinder head according to the instructionbook to 90nm. Did you experience this after your rebuild?
@OliverLee390 Жыл бұрын
I personally didn't, but it would make sense, as changing the headgasket would increase compression if it was leaking before
@deranocasper Жыл бұрын
Top job Oliver
@deranocasper Жыл бұрын
Have look at my channel I doing a tvo tractor rebuild
@deranocasper Жыл бұрын
Hello Oliver Hows tricks with you tvo I have a tvo you and you dad can check out my youtube channel i am going to be engine rebuild its a bare block at the min all the best with your tvo
@kevinkeenan9075 Жыл бұрын
Love your vids, could you show us around your Vicon spreader please, thanks
@christophernunn943 Жыл бұрын
Easy start!!....kiss of death erratic detonation will fracture piston rings lowering compression and then totally reliant on the stuff. They never came out of the factory needing it. A well serviced engine should only need heat from cold start, Is this one thermo start? I actually have a 702 and selling back actor as I have a few diggers and not required. Was told it was use in cemetery digging graves, had an easy life. lol
@howardporter2863 Жыл бұрын
Dont scrap it they are getting scarce try keeping it in one piece
@OliverLee390 Жыл бұрын
I’ve saved it from the scrapyard don’t worry, it’s back safe in my shed now 👍
@nicklad9463 Жыл бұрын
I'm sure there's a good reason why it was sent to the scrap yard m8
@OliverLee390 Жыл бұрын
I think it’s down to the power steering being knackered, therefore being basically unusable, I’ve got it running, hydraulics work, clutch brakes etc
@paulthompson8467 Жыл бұрын
That's a gem of a digger bit of tlc and she will be a great wee machine 👍
@mechanicalmoron2251 Жыл бұрын
stop buying them haw meny you got naw?
@OliverLee390 Жыл бұрын
5 tractors, 2 diggers now, never enough
@mechanicalmoron2251 Жыл бұрын
@@OliverLee390 leebe some for me
@paulthompson8467 Жыл бұрын
Good video a challenging project indeed best of luck looking forward to seeing more of your videos 👍
@OliverLee390 Жыл бұрын
Thanks Paul, lot to do on it, but good to learn from practical experience, part 2 should be posted in the near future
@af5579 Жыл бұрын
whens the will it run video fill it full of easy start
@OliverLee390 Жыл бұрын
The video of that is in the works as we speak
@muhammadasifkhan599 Жыл бұрын
Hi brother i need your contact number
@muhammadasifkhan599 Жыл бұрын
Actually i love tractor and i need some information about it from you kindly i will be waiting at your responce
Wonder if you could show me how the loader is attached underneath the tractor? Thanks
@OliverLee390 Жыл бұрын
Send me an email, [email protected] and I'll get some photos sent across
@MrCorynick Жыл бұрын
@@OliverLee390 much appreciated
@paulancill9744 Жыл бұрын
I have a 702 it differs from yours 23c engine but has wider back axle (?from 65) it is certainly wider than our 3 cylinder 35, the plate between the mudguards is set higher than yours, I replaced a missing ram on the power steering but it leaks wait till you try to top it up difficult to open the top and you need a long funnel to fill it! The exhaust rubs against the bonnet because it is turned to the back to avoid the lift arm.
@robertdavies922 Жыл бұрын
Very nice little machine!
@corrigansrestorationvideos9403 Жыл бұрын
Well Oliver Lee I was wondering have you any advice for me when using a ferguson potato spinner
@OliverLee390 Жыл бұрын
Make sure you have the tractor in low gear, preferably a 35 in low 1st or 2nd, with plenty of revs to prevent it blocking, but depends on your soil. Need to ensure your depth is set right too or you can end up cutting the spuds in half too, hope this helps. I've only learnt from trial and error
@corrigansrestorationvideos9403 Жыл бұрын
@@OliverLee390 thank you for the information it is much appreciated we are getting out potato digger tommorow we have a ferguson 20