The paper shop towel did it! I did the tapping to start and with the plastic housing being worn, this was key! Thanks, Gerard!

So why is the engine management symbol still there on the top left?

My bmw g11 keyless entry will not work. I’ve changed the battery. I’m able to use key open and close the car by pressing the buttons but the car will only start when bring the key towards the steering column

Doesnt work for me 😢 not sure what I am doing wrong.

Great, thank you 👍

On my 2020 I got to the menu, and get the wrench blinking, but then I never got the clear message...any thoughts?

I hawe a NON STOP steringweel vibration on 133-135 km/h . On load no load at this speed vibrates. Tires new, balanced , brakes 80% life left front 30% back , weels are streight, motor is ok . No sounds , no jerking , no play ...😢🫣

C'est un truc de malade normale je trouver pas !! Juste pour ta vidéo je m'abonne sorry

Hi! Thanks a lot for this. I just have one question and a moment of your time to check something. So, is this the same turbo as in VW Golf 5, 1.9tdi, year 2004? Lastly, this is my fault code for my car. Can you tell me if my turbo has gone. Thank you! 16618 - Boost Pressure Regulation P0234 - 000 - Limit Exceeded (Overboost Condition) Freeze Frame: RPM: 2520 /min Torque: 226.0 Nm Speed: 63.0 km/h Load: 70.2 % Voltage: 14.21 V Bin. Bits: 00001000 Absolute Pres.: 2029.8 mbar Absolute Pres.: 2499.0 mbar

Hair dryer was amazing when it happened to me.

Mighty tip that Gerard, Thank You👌👍🙏😎

Great job Gerard, Thank You👍🙏😎

Thanks for all this useful information. I recently replaced the heads and radiator (and thermostat) on my 91 Toyota pickup, and now the temperature is rising much higher than before on longer drives (almost to the red). With the bad head gasket, both coolant and oil were contaminated pretty badly by each other. So I am now thinking the cooling system may need a very good flushing 🚽. I am going to employ your flushing recommendations and cross my fingers!! 😅 🤞🏻🤞🏻🤞🏻

could also be the Front differential

Absolute waste of time

not bad, i was waiting for pvc pipe mounted on the wall but that'll do

Great tip!

Good tip. Nice and easy and it doesn't cost anything!

Thanks!!

1st!

Another great solution that is hard to find... well done.. I'm also from Australia wondering what do you use to access all wiring diagrams. We don't have alldata here I assume Autodata is the next best thing?

I made a video doing it the same way as @ericfeng8246 stated in the comment section. It works very well and if you are unsuccessful using this method I would highly recommend checking out this updated video for another option kzfaq.info/get/bejne/ftV8rbWZz9msenU.html

thank you very helpful information that same happen to my car now i can go to car shop

Thanks for your clear description of what is going on in this situation. My Captiva has a low pressure fault and I was told that the HP fuel pump needed to be replaced. I've stripped and inspected it and found nothing wrong with the pump. The valve operates electrically, but I'll see if I can get into it to inspect it for wear. I've been told by another service business that there may be a seized injector that could be causing the low pressure issue, so have to investigate that as well.

Thank you

Brilliant mate, I have this exact noise on my L200. Was thinking a turbo maybe done. But seems there is sealant around where the turbo joins the manifold. So this maybe the issue.

10k before tax lol.

Thanks for your video. It cleared up some confusion on the timing marks. I was about to pull the timing cover off and recheck it again. I was worried the chain skipped a tooth when I rotated it

Thanks a lot, it worked for my 2020 eclipse cross.

Same kind of sound im facing unable to find the issue 😢

Hello, I have a 2008 Ford Focus SE. It starts intermittently then shuts off sometimes shortly after starting it, or putting it in drive, I can even drive it for a while then the engine just cuts off even though I always have power. Other times it won't even attempt to engage the starter. I have checked my battery and alternator charge so that's all good as expected. I replaced the Crank Shaft position sensor already as well as the Ignition switch. After I changed the ignition switch it worked for a few days and now is even worse than before. I would check the code, but my OBD II receiver is not working, or my car is just not connecting to the code reader. The more I research this issue the more different answers I find.

2017 Nissan Pathfinder

I started watching your video and wondering why the tires were so cheap because my car actually takes the exact same size but then I realized this video is 6 years old so I think each of those tires is probably double literally in price right now in 2024!

Y friend you doing too fast sorry

Worked a treat ! Many thanks indeed 😊

too bad you didn't show the taking out of the bushing.

Good video. Just did a timinbelt and water pump and the vsa and check engine light came on. 1 code 0344 and it says it is a camshaft sensor. But I didn't touch any of the sensors. Sh-awd also came on. I reset the vsa light with this method. But it comes back up. I have my scanner tool, and it clears everything and the car struggles to start. Once started the lights come on and it runs fine. Have a camshaft sensor on the way just In case

I normally put one around the bundle and tighten it as I pull em out.

I’m just about to buy two front tyres for my wife’s diesel Clio and I’ll be going with a budget brand which are £50 each…fitted. I’ve had them before on other cars and never had an issue…she only covers about 5k miles per year and very rarely goes on a motorway…just drive sensibly and to the weather conditions and you will be fine.

Has the same problem we change this parts, is it working outside but dashboard still showing failure and with the same sound

Possible to get KZfaq on this screen?

Just done it with you, Thank you, quick and easy.

Genius

Yes! Preach brother! I get so pissed when guys cut the ends off the bag!!

I put a tiny cut in a corner to stop them coming out when I don't want them too but this looks better, I'll try it. Thanks

What kind of mechaincs do they have working at toyota? Smh im haveing a hard time removing mines

Or just use a Small Cable Tie to hold All the same together in an open bag

I've known that tip for years and I've been telling well trying to tell my father how to do it BUT father knows best 😂 there's no telling him.

Where do u get chart

It’s save to drive with this issue ? Thanks