Damn... fighting for every millimeter.

Not everyone has a welder. I have an easier way a long chisel & large hammer few whacks she'll come out

What are the special pliers called?

Its now good? Fix?

Where can i get that bolt ?

Badass. Thanks brother

Y si uno no tiene esa erramients con que se puede dar ayuda para sacar

Is the primary clutch bolt normal thread or reverse threaded?

Do you have a link for the tool by chance??

Built one this weekend and two pops she was out

Just got the 900 and was wondering why my Legend blows it out of the water TY for that video first one i seen about the issue...

how do you manage to get that much rust im an area where its suppose to be greased up? was your wheels able to turn?

Glad my canAm was easy

Thank you 🙏🏻 only video we could find

Is that a clutch puller you used?

Fucking hate this machine!!! Fuck you Minelab!

m50 x 1.5

now do you remember how you made that socket?

i hat a 600 mile ls engine like that they said to send it on out, cam gear sheared and caused the ticket

Where’s the spring for the primary

I have upgraded to a Equinox 700 and a buddy of mine had his equinox 800 break and he gave me his 6 inch from it. I been able to dig up some pretty deep targets so far.

Oh boy I’ve been there about 1 million times with Polaris and stuck CV axles

Thanks for your video! Have you any update on this? Mine does the same thing. Fe on minimum or maximum does not change anything for me on air test or in-ground test. Is it the machine or the coil? Have you contacted Minelab?

Do you have the whole video??

Thank you!

Donde podre conseguir el reten primario del clutch para una can am 450 2015

Looks like you're using the Full Sensitivity and getting ground Feedback from the detector and I have just recently got the X-Terra Pro and the Equinox 600 and also a First Minelab owner and I don't have the Detector's on the Full Sensitivity without expecting the ground Feedback and the Jumpy VDI and I started with 12 Sensitivity and worked my way up to get a better idea of what it was trying to tell me what the target is and I'm at 18 Sensitivity Now and like you when you get a Jumpy VDI it's going to be a Junk Target, but just lower it down just below the Full Sensitivity Mark and I'm not sure what it is on your detector but on the X-Terra Pro it's 20 and 😲 WoW it is a totally different Detector than the All the Time being jumpy VDI and Not locking to Any kind of Numbers but just lower the Sensitivity down and I found a target that was in the 6 inch range and I have lowered the Sensitivity down until I lost the target and then I raised it up until I found it again and it was At 12 Sensitivity and I have worked my way back up and I can really tell when I get a Junk Target And I don't need to be able to Dig a hole to China Anyway and the Full Sensitivity without any kind of ground Feedback.....

Interesting method, I will give it a try. Thanks 👍🏼

Thanks 😊

I've got the 700 and set my fe of 1 and have no problems

No-fake. It would pull the cv joint apart at the boot.

Let’s go let’s go treasure and adventure 💕🌺✌️👵

Is that a 36mm thread ?

Gotta push Ian. Got it👍

Da...😂 only been that way for last 29 years

Wow, mine 6" that i always used with my 600 works perfectly fine with my 700

Hey I just bought one of these. Are they supposed to be wobbly?

Shocking

Lots of Bells and Whistles on these Detectors. Thanks for sharing.. Peace

To get the stub shaft out of the cv axle I used the square tube on the tow hitch and a 4 way lug nut bar and 10 pound hammer after I cut the boot it knocked it right out

My brand new Nox 700 had a horrible depth of about 1-2" after several hunts before I realized it wasn't doing much. Not only the depth but the readings were all over the place and couldn't be trusted. I returned it for the 900 which is obviously greater but mostly because the 700 was clearly defective, whether it was the 11" coil or the 700. I wonder if there's just bad coils out there.

How did you change it?

My 700 is the same way. I have an old house and the yard is loaded with iron. For 14 years I have dug every non ferrous signal with multiple machines. Including the 800. I just got this 700 and I cannot believe how much non ferrous I have found with it. But it loves some nails, all bolts and screws even small ones, even when they are out of the ground. I cannot knock them out horseshoe or not and with ferrous maxed out. I don’t mind in my yard as I found a coins recently with it, a silver dime and a Indian head and several wheats and some relics. I can dig as many holes as I want in my yard. I found it is more of a pain in parks though. I really wish it had more adjustability. Because I used the 900 with a iron bias of zero and dug less iron than this 700 with it maxed out. The 700 will knock out rusty bottle caps effectively though for some reason.

They ever fix this issue as im wanting to get a 900. I'f not ill just keep my xp deus 2

Also, thanks for posting this video. Everybody else seems to see this thing is incredible.

I am experiencing the same thing. Unacceptable. I sold my Garrett Apex to get this thing WTF

How did you attach it to the vice grips?

Park 1 special "Loren Lemcke" program. 🤫

Seems that a $1000+ detector should have had this already taken care of. Do they not test these machines in research and development?

Any wiring under there?