There is more to come. stay tuned

Thanks

Thanks Buddy glad it worked out

No Problem, the difference between a 4mm shaft and a 3/16 shaft with a .150 cable, the rotational mass would be so little i don't think you could measure it. and you would have one less part to deal with { Prop Adapter ) a possible failure point. now If you needed to run smaller 4mm hub props, then the 4mm shaft would be the way to go.

no audio in the video i have no idea what happened sorry for that I will try to upload it again

Great Little boat and fun for the kids

This one has a ride pad on the bottom . Would love to know what outrunner motor you are running in yours? hope to get to the pond today to run mine. also if you have trim tabs on yours add a bit down on the right side to see if that helps your walk.

@@AdamEverythingRC I could email you the motor ad if I had your email but if you google MT-4250 -6s 1750 kv outrunner you should find it. $69 usd great motor

I replied about the motor but can see it. It’s a JP Hobby 4250 6S 1750 kv 12 pole outrunner $69 usd

@@jamesatkinson7517 Nice, you must be running that on 6S to get the 62 MPH with 1750 KV Good Job . love to see how you made a flood chamber

@@AdamEverythingRC I did it all the way to the tip and wider than the side of the deck in the motor area is all the way across towards the middle to the side of the 6s 5000 mah battery so there is a deck to it in that area. Also vent holes in the front deck area of it and side deck to let the air out.

Yea Stay tuned coming soon, weather has been poor but we will have some pond videos soon

Thanks Buddy stay tuned one more shop talk on this one then on the water next week

@@AdamEverythingRC awesome can’t wait to see it!

This is a horizon Hobbies plane. because of that they only make them for a sort time, then they come out with a new one. check horizon Hobbies web site to see what they might have now. i have had this plane for about 8 years or so and i'm sure things have changed with what they have. hope this helps.

Simple answer no. I think the smash is two narrow and the outerlimets is a step hull. I do like for the price the Delta force from OSE, Good Value lots of room. Big B has a DF 29 twin motor setup you could check out his videos on that. Also check out my DF 33 Build it is wider and longer or even look at the DF35 for a good Twin setup. the larger the boat the better rough water capable it will be. hope this helps.

Thanks

Thanks

This is a UMAX X3d I believe made for indoors. check Horizon Hobbies to see what they might have now. this one is no longer made. hope this helps.

Yes it has some custom Hardware, and stuff i did mods to, and some just mix and match stuff and thanks

Thanks I Appreciate That

I'll do that, I need the practice lol

Thanks The boat does handel like a dream. wait for the DF33 build Videos should be a great boat

Well can't now, you will have to check on the build with H2oMechanic2RC whet ever he does i'm sure will be amazing.

I was told the chaser 32 was a newer design. Have no idea but i liked that the DF33 was a bit wider.

@AdamEverythingRC yep that is a much better choice! I can't wait to see what you do with it. My BJ42 just got here last night! So excited to get her out on the water! I'll be making a video of it's maiden!!

I have led shot in them and use them to hold things down. works great !

Not sure on the rules and don't plan on racing just looking for reliable. Should be a fun boat. Got it mostly done so look for the build update.

@@AdamEverythingRC looking forward to it.

Yes it is one of my favorites, wish i could fix the skipping around a corner.

@@AdamEverythingRC I had a TFL outerlimits back when they cost basically nothing $220? I filled in the rear step and put a longer rudder and it handled like a normal mono.

@@FEboats Nice I bought mine around the same time

Keep Watching More to come on this one

The boat is a bit narrow so going 6S WOW my delta force 29 went 70MPH on 6S and on the small pond was scary stupid fast. I also have a video of the TFL Outerlimits going 60 MPH on 4S check it out if you haven't

Thanks looking forward to it

You will have it done soon I'm sure. Great Tug you will enjoy it.

The motor was a 3660 3050KV Rocket motor

@@AdamEverythingRC wow, it was moving

Congrats great job

Thanks Mate. We will have some more footage from the bigger water. right now, pond is to full of weeds

Thank so much . stick around lot's more to come

You're welcome

I'll be looking forward to seeing them

Sorry about the theft. check my other videos the 23" mini mono is also from randy. both were Gas originally

@@AdamEverythingRC I’ll check them out. Thanks!

That is a GREAT Idea I love it. And i can make the decals. not so sure on the driver because i'm not sure on the lid yet but Shell theme here we come! What do youu think of a red Tub for it?

@@AdamEverythingRC I'm not sure what you mean by "red Tub".

@@northwind9505 The hull will need top be repainted Hull and Tub same thing sorry about that

@@AdamEverythingRC All yellow with red trim .

My Purpose for the way i did this is so you can easily remove the bracket and servo if you need to ever need to replace the servo . i think it just makes it easier to do to get at the servo screws. And Thanks for watching!

@@AdamEverythingRC makes sense. I originally just drilled my hull when the electric version of the mean machine hull came out but didn’t like the bolts sticking through the bottom. Your way fixes that.

Yea i was trying to keep the cost down. the Flycolor Kracken 120 also fits just doesn't have the burst amps but that might not matter. i will try the Kracken and see how it works later on. Not sure when i will run 4s i have nothing that fits right now. i could go 6s ??? hmmmm

Your motor can do 4s I would not run the Kraken in preference to the Seaking because if the high max amps of the Seaking unless of course you already have the kraken. I also done my own cooling on the Seaking I put water cooling tracks right over the copper heat sinks that are under the standard cooling plate. Makes it a bit thicker but even skinnier. Big b at ironclad Rc on KZfaq runs your motor on 4s with around a 3616 prop in his shrimp outrigger at 84 mph. Using the flycolor 90. Pretty trippy.

@@jamesatkinson7517 By looking at the hobbywing Seaking 120 amp pro esc it looks Identical to the Kraken it even has the same wording when describing both units. and i have the Kraken 120. they both just don't have the same high burst Amps as the Flycolor 90A but have more continuous Amps so we will see.

You Know It

Thanks mate.