You could pump oil in through he oil pressure sender location to prime lifter before startup ?
@jacobyeater4125Күн бұрын
Everything about that car is awesome. I was really wanting to hear about the clutch setup
@badass6.0powerstroke10Күн бұрын
He definitely knows what he's talking about, he knows every square inch of that Pontiac engine, and he Loves Crower Valvetrain products. And the best part of all of it, No LS ! I'm loving it, that he left it Pontiac Powered !
@SleeperdudeКүн бұрын
Very cool setup
@Headsup9550Күн бұрын
Richard is a class act! The way he acts in interviews is exactly how he is in real life! Awesome guy!
@badass6.0powerstroke10Күн бұрын
Yes he is, very knowledgeable person.
@tuckermaas6874Күн бұрын
That’s my father how did you get all this information! Together thank you so much.
@red-doggracing5557Күн бұрын
A real man’s car !! Three pedals
@Nobody-ld7mk2 күн бұрын
Modern Alloys have put more time between catastrophic engine failures. Replaced a set of ARP 2000's five years ago & they were $242.00 from S*mm*t, not cheap but just pulled the BBC down with everything intact. Wish these guys would have gotten into Torque Angle vs. Torque Wrench methods of torquing the bolts for perfect stretch. I suspect manufactures are using torque angle gauges when torquing for final bore sizing. I use a rod stretch gauge when my rods are un-torqued for the first time, stretch is always ultra consistent.
@tonyminna91082 күн бұрын
Hard to find your channel ....kept getting a golf guy
@ultraspinacle2 күн бұрын
I enjoyed the heck out of this.
@keithmceuen87752 күн бұрын
Is this only dry deck or is available as wet
@patrickwendling67593 күн бұрын
Thank you for your knowledge and videos USA 🇺🇸
@danielwilson66653 күн бұрын
That’s …. Well I mean…. Umm I think…. Will it….Did you…… How does…… I absolutely agree, it’s amazing 😉🏁
@thejollyfrog27913 күн бұрын
Right it’s a zero warranty money pit 😮😮got it 😢
@thejollyfrog27913 күн бұрын
How long is this warranties for ?
@brettrussell81003 күн бұрын
I have an aluminium 540 with 11.5 comp, solid roller with 270, 285 degrees @50 with 315 cnc ported Brodix heads, sheet metal intake with twin 950 APD carbs, my combination make a little over 800 hp but at 6400 revs, power drops slightly the more I rev it, can't work out how this one's revving so far and making similar power with less cam and comp?
@coryjordan23683 күн бұрын
whats the lift on the cam, big cubes need more cam. also, what do the heads flow at higher lifts?
@nickmorrow38293 күн бұрын
I have pictures back in the early 80,s of Larry racing the late Elmer Trett. Larry had experimental wings on his bike. You have to love Larry and his Team
@-Primer-3 күн бұрын
Sorry to hear you live in a communist country. Maybe you will be able to escape one day to America. Good Luck.
@user-ni8lb2vr5t3 күн бұрын
Dude were is the billet 7.3, dont care about cummins
@timweb15104 күн бұрын
I wouldn’t buy products from these pompous fools talking down on the paying customer
@bigboreracing3564 күн бұрын
What did they say that you do not agree with?
@bowsertownes3 күн бұрын
These guys are absolutely correct. I'd buy from guys like this
@bigboreracing3563 күн бұрын
I do not know what hurt the OP's feelings. He obviously never built engines for racing.
@karlsracing84223 күн бұрын
Must've not listened to their advice and limitations of the their products.
@superconscious.4 күн бұрын
🔥
@allanhmelnitski9784 күн бұрын
Does "add timing" mean "advance timing"? Make spark earlier?
@TrentGustus5 күн бұрын
Is it OK if the exhaust seat is too close to the intake seat to flat spot them to fit in a cast iron head? I've never seen this before , usually the valves are far enough apart that this would never happen, I bought an engine fitted this way
@Peternielsen886 күн бұрын
Very well explained, thank you!
@shawnwalsh54306 күн бұрын
Why people have to have music playing during a video is beyond me!
@unclebrentsshed42537 күн бұрын
Who sells these engines in the states and how do I go about getting one??
@jimcatanzaro78087 күн бұрын
Better have a heavy dudy cooling system
@jon-jo5pn7 күн бұрын
Stop being so rude! Get the S H I T (tobacco) out of your Mouth when you speak in a Video!
@AlloyedFrequencies7 күн бұрын
Thank you very much
@racerz1298 күн бұрын
Never thought to cut open a spark plug. I've been schooled. 😮
@Andrew-uw2ir8 күн бұрын
Those "mans pushrods" should be called "drum sticks" for obvious reasons.
@davidvasko63008 күн бұрын
smokeless power rocks
@michellee83698 күн бұрын
🇦🇺👍
@scottreed54608 күн бұрын
So who is Wild Bill? We didn’t see him. Did this include mild salsa? Mild salsa is my favorite..
@David-yy7lb8 күн бұрын
And not one word about re gearing the truck to lower gears for taller and heavier rims and tires to put the engine back in it's power band and lessen the strain on the transmission
@stretchhfab73159 күн бұрын
This is garbage garage talk... Do your math and you'll be fine.
@dastarddizaster9 күн бұрын
Who makes the electric water pump? Is it a custom front cover water pump combo?
@Mark-um7ey9 күн бұрын
Awesome to hear Jim O interviewed. He is one coo,l layed back dude. Great to see Clay and him together with a great sponsor.
@dannybrooking68869 күн бұрын
Awesome thanks from NZ
@67VWForever9 күн бұрын
Saw this 68 at EMPIs Dino run when i first saw this i said SICK as hell the biggest horse power I've seen in a vw
@garrylundgren686911 күн бұрын
Great vid mate.
@thomaskreutziger771911 күн бұрын
hi, is this Fluiddampr for the Land Cruiser 4,2L 1HD-T 6 Cyl. Inline Turbodiesel available ? Thanks Tom
@Pwnulolumad3 күн бұрын
The fluidampr has models uniquely made to fit various vehicles, Visually they all look the same but the bolts have to match your engine, email their website and they will reply with the exact one you need
@Carl_Jr11 күн бұрын
They're called wheels, not rims. The rim is part of the wheel.
@goodtimejohnny897212 күн бұрын
ADAS problems, yearly ball joints, cv axles and 4x4 actuators, oh my! Leave it stock and if more height is needed buy a larger truck. Or an airplane!
@totalperformancediesel832812 күн бұрын
more work for brakes
@magnus916512 күн бұрын
This young lady just keeps getting better and better with her delivery. Great job. She knocks it out of the park.
@413x39814 күн бұрын
I cut this way short because all I could hear was the guitar. Amateurs.
@terrybeyer423915 күн бұрын
Pete I injoyed this video a lot - but there back ground music ? . Could they edit it and sub in some of the music you make 😅 lol . Great job , injoyed the shop tour.