I did the flat head test and the generating light came on, but then the inspect cell light also blinked. Do I need a new cell and a new switch? I did also clean the cell skimmer and filter
@CelestesPattison-hf8kg23 сағат бұрын
Video background noise is to loud. It sounds like traffic or perhaps it’s raining. Otherwise great explain of every aspect of the equipment and how to install accurately. 7/31/24
@ericlambousy2417Күн бұрын
thank you, sir. this will help me to diagnose my dad's generator on his pool.
@hectoralbavera12372 күн бұрын
Awesome video, got it back on the schedule time, thanks 👋👋
@emkmd6 күн бұрын
I have an ASUS mesh wifi system and the omnilogic would not connect after a severe storm. I powered off the ASUS nodes to force the omnilogic controller to connect to the main router and this worked. So maybe a network issue.
@ESmith-d2d6 күн бұрын
Two Jandy actuators failed. The first one had an internal failure, the capacitor exploded, so I replaced the actuator (online, 2-day deliver).. The second one was pristine internally, the switch moved the motor in both directions and I troubleshot the board as described in the video. Before I ordered a second valve I checked the continuity of the cable between the board and the valve. Found an open circuit in the white wire (the cable was nicked by a weed whacker I think). There was enough extra cable to remove the bad portion and reattach inside the valve (no splice required). Reinstalled and works fine. Troubleshooting and looking for an easy, cheap repair made this a $200 repair with no service call. I figure I saved about $300-$400 by not having to call the pool company out.
@sermie116 күн бұрын
OMG, you just saved me $150 just for the guy to come out and check! My actuator wasn't moving to the OFF position when we turned off the solar heater at the panel, so all this time, hot water has been pumping into the pool, and it's been like a soup this summer. Thanks to your video, I was able to locate the switch underneath and found that it was in the OFF position. I switched it to ON and the actuator immediately started to move to the OFF position! WOO!!! My pool will no longer be a bowl of soup this summer! THANK YOU!!!
@edgarcastelli57646 күн бұрын
Great install question is the main housing a Plastic housing ?
@CesarHernandez-gn4sy7 күн бұрын
Thanks for tip I will try this
@jonathanarndt25610 күн бұрын
Thank you for taking the time to post this video
@mikepj102511 күн бұрын
Barely hear you man. The music is unnecessary. Good job though. Big help. Thanks
@TheDududu4411 күн бұрын
I use the screwdriver technique. If it blink, but doesn’t turn on generating, is the problem the flow switch or the board ?
@artharutunyan12 күн бұрын
Why not use flex tube and not have any joints there?
@joemerkel2012 күн бұрын
Do you have any tips as to why the metal arm gets caught on the triggers? I have the correct triggers (brand new) but they don’t trip the pump on
@JesusGonzalez-qp3ij12 күн бұрын
Cómo aumento la presión de agua en mi equipo
@capybaralover8812 күн бұрын
Great video. Thank you.
@LouisBodnar-zp8ku14 күн бұрын
I live in Naples Florida, where can I buy that air botton?
@lazhernandez83415 күн бұрын
What does invalid cell error mean
@christiemorris429816 күн бұрын
The most helpful Hayward video I’ve seen so far! Completely explained step by step how to solve our problem! Thank you!!
@JamesRyanHarbour17 күн бұрын
What City, state you work in? Love your tips! They work in the field like you say they do!
@keithwoods195118 күн бұрын
Stop the music when you're talking and we can't hear you when the pump is running
@jeaninedagostino650119 күн бұрын
Thank you! You saved me a lot of money in labor.
@edilynnclermont624719 күн бұрын
I check my stll not working and everything looks good but still it not working
@Anthony_A_22 күн бұрын
Mine doesn’t turn off with pins nor manually..any thoughts?
@DJNinoSabroso23 күн бұрын
Wish you would have shown where the color wires get screwed on (which connector, which order ) for the power .
@anthony755724 күн бұрын
Can you come across across the swimming pool with an ancient drain cover?
@the_jaggernaut24 күн бұрын
You can also put on some gloves and scrub the tablet against the black algae spots as well!
@marinepoof25 күн бұрын
any chance you know what part of the board goes bad causing this issue?
@lalakers48026 күн бұрын
I can't hear this! THE MUSIC is drowning out your voice!
@user-iz2jg8jz4h26 күн бұрын
Mine is black screen all of a sudden is there a on off button?
@consensusrealtysolutions29 күн бұрын
where cn you buy the pins?
@camf33Ай бұрын
Excellent.. explained in details and professionally, I did noticed one thing when I pulled mine though - noticed that no matter what direction the metal contact is facing (supposed to be face the water flow) it all rotates together when you screw the cap on, so essentially the entire housing moves which can position the metal flap in the opposite or any direction, unless mine is not well that's what it did to me. Nonetheless, after I re-screwed it worked well.
@duller49Ай бұрын
it works thanks 🙏🙏
@jasonandbensonАй бұрын
Why when I upgrade my system 4.8 to 5.0 and all the sudden my pump stop working
@richwash51Ай бұрын
Thanks my friend just looking at the job I got some good ideals from you Thanks again
@KennyP-i7gАй бұрын
Thanks for the diagnostic tip. I used the screw driver test and it showed the flow switch failed. I replaced it with a Hayward replacement flow switch and it's working now. The video saved me a lot of time and avoided a costly service visit!
@EliteSwimmingPoolsTVАй бұрын
You’re very welcome, I’m glad to have helped you with this and saved you time and money. Be sure to subscribe to and like our channel for all new uploads. You’ll surely come across other videos that may give you more good advice and help. Thanks for watching and commenting on this video.
@jek4313Ай бұрын
What happens if it just keeps blinking the no flow light and doesn’t go back to generate does that mean the board still works ?
@EliteSwimmingPoolsTVАй бұрын
If your performing the screw driver tip, make sure your making proper contact on the contacts where the flow sensor connects into. If you are and the light keeps blinking and doesn’t switch to generating this means the issue lies on the board and not the flow sensor. If the board was good and you make good contact on the contacts and the display switches to generating that means the board is good.
@aprilwaller123Ай бұрын
Did you use chlorine tablets that you put in a floater????
@Aloha96789Ай бұрын
Skimmer socks work great. Put a new one in the skimmer basket to hold it open, pour in the smashed puck then take it out and put a knot in it and toss it in the pool. Move it around if you have multiple spots or even use more than one.
@WorthyCoringtonАй бұрын
Guys this is great. I've got a 30yr old plaster with leaks at one skimmer and 2 return jets. Currently I have them plugged & just using the floor returns. I'm putting it off but I'm gonna have to break out the wet saw and some shovels. Knownanybiy in MD that does a good job for a competitive price?!
@Asylum-SioАй бұрын
We should form a P2W Union ... if you want consideration first you must demonstrate that you are many, united and resolved. Strike first to show the community is together ... and that opens the floor for serious consideration. Until that all you will get is lip service and excuses. Money would come from the influx of new players so we won't completely stop the flow ... unless the market has already been tapped. But at least then the community will have a gauge of what power we do or do not wield with our pocketbooks
@JorgeGonzalez-m9yАй бұрын
Outstanding, thanks for the info.
@chadroth2722Ай бұрын
Very helpful. Thank you 👍🏻
@cibonthesaint8903Ай бұрын
Hey bro, is it my eyes or do I just not see purple activator?
@Yabbadabbadoo75Ай бұрын
Bro that background music too loud. I can’t concentrate on your voice lol it’s annoying
@ShaneOlchАй бұрын
Brilliant idea man. This would save a lot of bed space instead of having cases or jerry-jugs. Where did you get the tank and did you have to get a NSF/ANSI Standard 61 tank?
@bigguy8586Ай бұрын
I need help unclogging a bottom drain. How did you get it to push instead of suck.
@cbijames7Ай бұрын
Great video thanks for the help
@cbijames7Ай бұрын
Take the little gear out and put it in last then it should work remember you took it out first when you disassembled it
@MIAMI305LIVEАй бұрын
Oye put a plant pot over the rolled up hose. That things gonna be crispy from the sun! Good 👍🏼 video….
@EliteSwimmingPoolsTVАй бұрын
Thanks for watching and commenting. I’ll recommend this to the client.