how do you fit the fine tip?

Can the finishing resin be used to be the final top coat for a dining room table? Is it durable against water stains, food stains and dents from writing on it with pencil and paper?

Hi,Where could I buy the main landing gear for the 1:3 scale cub? Thanks

Is this still available?

I have a question, why don't you show what to do with the z-ends in your video????

will storing it in refrigerator help it last longer/

Looks as if the wider strip will provide more stability for the 3 mounting bolts.

its a HURRICANE ....not a Hunter

Hello, I. Have cy model lavochkin la7 84 inch which one is suitable for my build? Thank you

How do I decide between 85 or 90 degree ? for my p-51

Hi. Can I mount 3/8" dia. Straight RoboStrut on them?

Hello I am curious about these. Like the Medium what that means and what does the CA+ stand for ? Thank you very much

I don,t see how the over centre link gets unlocked

How about a video on the joys of getting all 8 hole to line up the first time, without hacking the wood in between the horn?

What's the reason for this video?

I always struggle with PVA (white glue) based glues for plastics...They tend to be a static related glue in terms that they dry and hold only by static than a weld...PVA's work better on porous material like wood and paper than they do on plastics...The upside is they don't mist or fog canopies...I've seen folk use Tamiya liquid fast drying glue on canopies with success but you have to be careful and only use a tiny amount at a time...There is a case that if it's a model and not a toy then it shouldn't see any hand traffic but I like to make sure my models are put together strongly at least...I'm still experimenting at the moment to find a good solution to the issue...

Would you just cut the same amount off of the spring as you cut off of the housing?

Epic glue moments

Does this product have a wax on the surface after curing and cause paint adhesion problems ???

Does the zip leaves residue ? I want to glue a toy and I want to avoid changes of color? Thanks hope someone can help

Too bad you have to wait 3 to 6 months before you actually get any gear you order from this place because they don't make it until you order it, but they fail to mention that on their site, im still waiting for mine ,then once you get them you still have to make them and buy the necessary taps and drill bits.....

Hi; It would be nice if you can develope a next generation to have a lead harness to turn it off with an exturnal switch. I think you would have a better sale interest for it. I will still get one though. A very nice product. I have a question. is it a good idea to leave the recharge cable to the unite with out always having to gain access. I was also thinking of making a quick disconnect addaptor for it

I find youre products , VERY CHEAP , PLUS

Desperately want but bloody can’t get in anywhere in uk .. what’s the point so angry..

are the mounting holes the same as the air ones?

this video had no help, I have to order 2 net top tubes and parts bags, trying to silver solder the bushing in place, the (Plastic) stopper, melted and now that top is no good, then the other one, trying to tap it, the tap broke in both holes, what the hell is that made or, I used these taps for aluminum engine mounts with no problem.. also I had to POUND the bushing in the top tube???

Good informations.90 degrees or 85 degrees..which one is better for Hawker Hurricane?

Answered all my questions. Awesome

What is the cost of it

How do you coordinate operation of the doors with the gear?

Voltage regulators should be avoided if possible. They have a slight draw all the time, so unplugging the batteries is required. This is just too easy to forget, and always ends up killing your battery due to low voltage. It would seem sticking with a 1S cell would be optimum if that is enough.

I am thinking about using these to convert my Sierra 1/5th FW 190 gear. I have had nothing but problems with air leaks. These gear require solid air pressure to keep the gear locked down. This has cause lots of problems on landing in particular. I hope this works.

How do you know that you have the right spring tension? I have a Ziroli Stuka with your struts and I think I might need to lighten the spring tension.

What is the fine tube which is in the cap, for ?

Hello, can you do a video how do you create recharge sistem?

hi guys..will these 815 rse's fit the 1/7 scale 64 inch wing span P-40 from top flite?..an do you have any available at this time..i hope thanks Phil

hi...do you guys have retracks for P-40 1/7 scale topflite 64 inch wing span...electric?

Have had one for years. Love it because you can use it for many shapes, Including placing the pads flat to lay a wing across. Problem is with time the "Rocker Ears as you call them get loose and end up shifting, or falling off easily. Stopped using it for a while because of that. Was looking at it the other day and put Velcro over the "Nubs" and in the "Rocker Ears". Now they stay in position well. Wish I had thought of that years ago.

What is the weight in grams of your 1/4 scale (690) main landing gear?

Are these still being made? Can I get them in Europe too?

very nice

If you are going to use a separate battery for the retracts do you also need a second switch ?

What’s not said is that when using robostruts you will have to fabricate gear door holders to mount to strut and door. Stock retract door hardware won’t work since the retract unit and robostrut has no real clearance when in up position. Also the wheels will sit a bit higher out of wheel well with these.

Nice ! BTH what are the 4" wheels, also Robart (what part no.)? Thanks

hi i'm owner of giant black horse fw 190 2.6m the diameter of wheels is 161 mm and hole axis 6.1 mm may i order a 6 inches wheels to fit in my plane ? i'm living in in France do you still shipping in my country ? Best regards.

Hello. My paint shaker does not shake anymore. All AC current are working fine. It seems that the electric motor does not have enough power. Your webpage does not have support for this particular product.

❤️❤️❤️❤️❤️❤️ i hope the FW 190 ist aviable soon. I order the Plane at March.

what is the ID of the Robart Tubing?

Bloody hell,it’s styrophome,lol,looks like a piece of junk