I have the black one, amazing guitar. Knew it was rare but not that limited....
@EricMorettin9 сағат бұрын
@@mrchristosatanico oh yeah super rare from what I've read!
@cmichalski42020 сағат бұрын
i have an ormsby junk after 1 year all the frets sprout goin down neck literall cracks below frets and the finish on neck flaking off it just sits there o never play the thing i play my firefly more junk never again i messaged perry asked a question blocked me like a dick
@cmichalski42020 сағат бұрын
its a metal x 6 string
@braaijmakers21 сағат бұрын
Where is the rocktron in the signal chain?
@jermizzeyКүн бұрын
Just did this to the jack on my active Schecter which was cutting out, and it's nearly good as new, now. Surprising how much those contacts can oxidize over time
@LordDimeКүн бұрын
did you use any peddals or is this all tuning and strings?
@EricMorettinКүн бұрын
@@LordDime gear list at the end of the video!
@mishswb4950Күн бұрын
I like 11 gauge strings on my PRS SE. recently, a new set the high E feels tighter than it used to be. I know they are 11 gauges, I have played these before, they are my regular set tbh. Just being clear with context, I can hardly bend a hole step on the high E. My action could have changed when having the strings off maybe?
@EricMorettinКүн бұрын
@@mishswb4950 the neck might have bowed a bit depending on the truss rod stiffness and weather conditions which all affect the neck.
@mishswb4950Күн бұрын
@@EricMorettin the neck did look like it curved a bit by the gap in the strings. Doesn't look as even as it did before
@mishswb495015 сағат бұрын
@@EricMorettin that was it actually. I tried it myself for the first time. Long time player, trying to learn more about the instrument. They feel as loose as they are meant to again for 11 gauge strings. I just prefer 11 gauges. Thick enough for my slide playing as well
@bloodswarmsКүн бұрын
Man, that guitar has to be the heaviest guitar in the universe.
@fredpastukh3460Күн бұрын
You can just flip red and green wires on neck pickup and live pickups on same position and have same result.
@manueldelgado47282 күн бұрын
😮 the Chinese one sounded better
@manueldelgado47282 күн бұрын
My Chinese one has original Floyd
@EricMorettin2 күн бұрын
@@manueldelgado4728 probably upgraded
@tfejulienewmar3 күн бұрын
Wouldn't this cause uneven playing action above the 12th fret?
@EricMorettin2 күн бұрын
@@tfejulienewmar not from my experience
@Mr-Sas3 күн бұрын
17:36 riff?
@mrnobodyinvr97623 күн бұрын
You need a pedal to select just One channel on the amp. I have the same amp from back in the day, and ya, you need a pedal to switch modes.
@EricMorettin3 күн бұрын
@@mrnobodyinvr9762 that you do!
@Urdadcallsmedaddy3 күн бұрын
I cant even get one of these now they cost a entire body
@Urdadcallsmedaddy4 күн бұрын
Thats really a interesting guitar considering its converted to a floyd rose which is sick
@jamesgreen53714 күн бұрын
I thought the strat sounds better
@EricMorettin4 күн бұрын
@@jamesgreen5371 it's easier to mix compared to the JM
@stanleyjungleib6505 күн бұрын
That's an output jack.
@poisonfortheweak5 күн бұрын
This is a great example of a solo where the newer players are like ok… yeah I got this… get halfway through it… oh- little run here, but it’s slow… more like a walk… that’ll take a little practice but been working on my scales- it’ll be worth it………. …. Aw, sh-t.
@gearhead20175 күн бұрын
Deoxit or generic contact cleaner will work,deoxit is really good
@BattleofTrenton5 күн бұрын
Is there a dime slime build. I just got a Chinese one and was interested in making it correct
@EricMorettin5 күн бұрын
I don't have one on my channel, but if one comes by and needs an overhaul I will make it happen.
@AaronBowley6 күн бұрын
thank god, when you first showed the action on the guitar i was like wtf that is super high, then you were like yeah we're gonna get this low and im like yeah im down for that
@jonsierra7236 күн бұрын
Just what I needed😅 it’s like if you knew what I am struggling with lol
@EricMorettin6 күн бұрын
@@jonsierra723 happy to help!
@NoJobRob6 күн бұрын
hey man do you have or can you make a video-i have a couple guitars where there's a loose/bad connection to the bridge humbucker and I have no idea what I'm doing back there lol. Thanks for the great content
@dorkwithsometork6 күн бұрын
I give my view
@burnoutmasters74067 күн бұрын
Is the Carbon copy used for “This Love”?
@EricMorettin6 күн бұрын
Since it has the mod/chorus button, I'll engage it for clean parts like in "This Love" and for solos
@reneraymond78077 күн бұрын
Fantastic!What gauge of strings,and tuning?
@MrPhantomdream7 күн бұрын
With wat amp system are you playing the children of bodom lick?
on all my guitars I have slight relief, as an example, under tension (tuned to how you plan to play), with the 1st and 17th fret pressed, measure from top of fret to bottom of string (gap) = 0.006" [0.15mm]. also, NUT height is important so that strings don't produce sharp note as you press them near the nut, the gap at the 1st fret with the third pressed = 0.004" [0.10mm]. once Neck and Nut are set, bridge or string height. if I go below, gap = 0.050" [1.27mm] Low E @ 12th fret and 0.040" [1.0mm] High E, then I have to play too soft as to not get buzz. I think if you can get Low E 0.060" [1.5mm]/High E 0.050" [1.27mm] gap your guitar is playing well! But if I can throw anything out there to new bloods, check that neck relief 1st, the nut will be high if you just purchased the guitar or haven't had a setup done. Set the string gap to 2.0mm on the low E and 1.75mm then play and adjust by feel and how much buzz you can live with remembering that most of that buzz is acoustic and will not be heard when playing at volume as well as, all electric guitars have a little buzz or fret noise. (I only say all of this cuz I was driving myself crazy chasing low action, the internet had me convinced if I couldn't get a 1mm string gap with no buzz something was wrong with my guitar! That's BS! by the way ) Good luck!
@adeptusslugusgaming7 күн бұрын
Did HB ever address these issues?
@EricMorettin7 күн бұрын
@@adeptusslugusgaming not sure! I hope so
@ShawnWrona9 күн бұрын
Man… that flanger/doubler sounds great in flange mode! I need one!
@EricMorettin9 күн бұрын
@@ShawnWrona not bad eh! I wish it could be powered off a 9v adapter though
@cursetheserpent9 күн бұрын
I had one of the original ESP Custom Shop Japan guitars of the black with glow in the dark sawtooth and pinstripe model.. Got stolen from me in 2008
@_jovian10 күн бұрын
This is the wrong unit for your guitar. The pin version is for non-square blocks. Floyd rose style blocks require the small clamp version. When marking the where your claw is with the tape, marking the back of the claw is incorrect, you want to mark where the actual claws are so that the springs are in the relative same position regardless if the original claw is a different size than the tremol-no claw. Wrapping the ground around the claw and held by the spring is a horrible idea... just strip the wire more, twist the strands and create a hook with the exposed wire then hook it onto the screw and tighten.
@themixmusicandmore628011 күн бұрын
I need your slime..... The guitar i mean!😂
@EricMorettin11 күн бұрын
@@themixmusicandmore6280 😬😬😬😬😂
@caiden3111 күн бұрын
I think the China guitar has just a warmer sound but both sound great
@Malum0912 күн бұрын
Damageplan riffs are so underrated.
@TranscendentBen12 күн бұрын
Check the STRING HEIGHT AT THE NUT. If cowboy chords feel hard to play, it's probably the strings too high in the nut slots. This is a problem I've often seen in inexpensive ($200 or so) guitars, whether new or used, because they've never been through a good setup. The nut slots are higher than they need to be to guarantee no buzz when it's first put together, and that's "good enough" for cheap guitars. It's "too much" to do it on the assembly line, it takes (too much) time for a guitar tech at a retail store to do it, so it doesn't get done. I can understand hesitation to show this in a video, it needs special tools with a different width for each slot (or even each string gauge) and experience with not making the slot too low, but it has to be done to make a really good-playing guitar. A few comments mentioned this, but I want to emphasize that the right nut slot depth is essential for a good-playing guitar.
@Vagen_d12 күн бұрын
Washburn should start making these again.
@EricMorettin12 күн бұрын
@@Vagen_d it won't happen
@kg1010112 күн бұрын
Awesome cover!!
@EricMorettin12 күн бұрын
@@kg10101 thank you!!
@nomadnick72612 күн бұрын
Badass cover dude. You just earned a sub. Got any tabs for this underrated jem?
@EricMorettin12 күн бұрын
@@nomadnick726 thanks! Learned it all by ear actually
@jasonscott239012 күн бұрын
Kick ass !!
@EricMorettin12 күн бұрын
@@jasonscott2390 🤙🤙
@RayzaEFC12 күн бұрын
Do you use the hardtail/dive only mode for it?
@EricMorettin12 күн бұрын
@@RayzaEFC yes
@RayzaEFC12 күн бұрын
@@EricMorettin any good?
@EricMorettin12 күн бұрын
@@RayzaEFC Yes it works well!
@aidab725813 күн бұрын
kickass!!!!
@Adam_Pagan13 күн бұрын
🤘
@EricMorettin13 күн бұрын
@@Adam_Pagan 👊
@vincemcman408613 күн бұрын
Washburn sucks. They gave up on these like immediately. It wasnt that they didnt take off. People romanticize them, and they forget Washburn fumbled the bag with Dime.
@paulgorhamiii992613 күн бұрын
Amazing cover bro, Dime would be proud.👊
@EricMorettin13 күн бұрын
@@paulgorhamiii9926 thank you 👊👊
@LordDime13 күн бұрын
bad ass album everysong is a hit nobody appreciates it
@EricMorettin13 күн бұрын
@@LordDime there are some gems on it
@rottingcorpse600213 күн бұрын
Really wish I had kept mine. Sold it in 2010 to a bro who reeealy wanted it. But I still have my D3 slime and Cross quilt top prototype.
@rottingcorpse600213 күн бұрын
Note, you pickup selector switch as replaced at some point. The original D3 switches are all metal, no plastic tip.