Is there any company that sells LED brighter lights for these
@mrnobody922711 ай бұрын
Would this work for the discovery 4 too?
@mrsatan686011 ай бұрын
I have a 2008 HSE Super
@mrsatan686011 ай бұрын
Auto Zone I went to at 7pm they didn’t have 1… the guy called the next store over and they had it. I got it for $119 after tax.
@mrsatan686011 ай бұрын
Thank u for your video. I will install my D1S HID Xenon Sylvania 35w Low Beam Headlight. I love my Range Rover. 👍
@amaliopratti206811 ай бұрын
which harness was used for this? This is what I need!
@Smachine62 Жыл бұрын
Hello. Do you have the part number for the loom with the green plug. I'm searching for one to fit my 13 pin socket on my range Rover sport. Thanks
@Emreece33 Жыл бұрын
These instructions do NOT work for a 2013 Range Rover Sport. If you purchase the OEM wiring harness kit for this make/model, it has two connectors. The instruction booklet only has illustrations and makes no sense. However, for my 2013 RR Sport… I did a lot of digging to find that you must remove both taillights and the bumper cover (tip: remove the tread plate on top of rear bumper to access 4 clips, and all the other small screws on the bumper are around the bottom and fender wells). Once the bumper is off, you’ll see two cords with dummy plugs attached to the bumper frame and that’s what you’ll plug the new wiring harness into. There is NO need to open the interior panels for this make/model. It does help give you more room to work to drop the spare tire too. Hope this helps!
@dookiebraids246 Жыл бұрын
Does it need to be speacilly programed at dealership ?
@baileybrown521821 күн бұрын
THANK YOU I HAVE BEEN SEARCHING FOR THIS ANSWER
@supertorton3134 Жыл бұрын
ja, ja, ja, ja...
@FatSausage Жыл бұрын
Excellent video, answered all the questions I had thoroughly and in a timely manner!
@Sturb100 Жыл бұрын
I followed this. All good except the end doesn’t explain that wipers stop position isn’t as simple as just putting it all back in the same place (which I did and the wipers ended up in the middle of the wind screen.). You have to let the motor cycle to its stop position before tightening up the bolt.
@mrhuemac66072 жыл бұрын
And wich bulb is?
@vfpaintjobs2 жыл бұрын
Can you tell me why my trailer light flickers at the I turn all of my lights off or even when they're on?
PiRadian, thanks for your video, it was very helpful 👍
@stephenhammond97933 жыл бұрын
Thanks...really well explained. The new harness the looked impossible to work out till I saw this.
@justinbarnes54983 жыл бұрын
Thanks so much... I was under the impression that the rear-end differential cover had to be removed such as in the lighter duty trucks, but my Ram 4500 is like yours, a simple removal of the bottom drain bolt to drain the fluid, then removal of the fill screw plug and fill the fluid in there. I will be doing mine tomorrow morning, but wondered do you have any issues getting all of the fluid out of the new bottles into the fill hole without clearance issues, or did you need to use a funnel or similar to assist? Also, do you seal that bottom bolt when reinstalling with rtv, or just reapply and torque? Great and well done simple video... you have my like.
@mr.vega17014 жыл бұрын
What is the model/part number of the harness being installed?
@617632robert4 жыл бұрын
Great video! Saved me some cash!
@vfpaintjobs2 жыл бұрын
Did you find this wiring harness and do you have the part number , does any one
@peterbuilttough34064 жыл бұрын
Use de 21mm it will be a tighta, 22mm may stripa da bolta
@arkansaspatriot78344 жыл бұрын
How much does it take to fill
@myronwilliams8032 жыл бұрын
How much does it take?
@skyper200064 жыл бұрын
What is the make and part number of the harness please?
@johnregal50986 жыл бұрын
Next time you do the front axle drain on the Magna-Steyr 275 can you do a video on that. I have a Ram 4500 and it is time to do both axles plus transfer case . Thanks.
@mikescalise39136 жыл бұрын
Great video! Thank you that is exactly what I was looking for! I need to change out my 5500 I also use for car hauling.