Make sure that your system is grounded all the way back to the outlet, a cheap HF meter will do the trick

Thank You. I’m looking to build a jig of this nature, this is far and above the best I’ve seen. To improve the hold on the log adding sharp pointed screws that stick out about 1/8” in the clamp pads.

A lot of work to get that floor drill press mobile.

My 17 glitched now my 2020 did today radio did work at first but once i turned you tube off then wouldn't turn on kill power to battery

Thanks for your video. Now it’s been a few years , how is your pmr running now ? Any must do fine tuning tips , that helps the function of a new out the box pmr ? Thanks.

My 2020 sierra 1500 failed on brakes at 4000 miles brand new, the truck was totaled and I am lucky to be alive left disabled, still healing.

I have the same problem 🤦‍♂️

It's your HMI. The HMI is the brains of the infotainment center.

Freaking Chinese? But American then, but you're likely too cheap for that.

Very nice work Sir. i wished i had a band saw....

By the time you spend over 250.00 on the M carbo upgrade kit you could buy the new S&W 22 magnum pistol and have a solid gun.

Yep it’s quite annoying and good on you for finding and providing a solution option!

Here is a video on the issue and solution. kzfaq.info/get/bejne/h6ylZ66lu8m3gXU.html

Kirk , I get it and you're not wrong . But my friend has spent 400 bucks on after market parts he could barely afford just to get it to function . Spent enough on that pos piece of plastic that he could have bought a real gun .

I just took my new PMR 30 too the range. I did nothing too the gun but load it and shoot it. I did not lube it at all. I shot 100 rounds through it and only had 3 failure to eject all the way. Not bad for a new gun. I have since disassembled it and lubed the hell out of it. No more problems. Love the gun.

Love it👍

Ryobi is Japanese company,

If kel tec has so many problems why buy them

No one ever mentions it, but I wonder if there aren't torque specifications for those screws were you can mount a Red Dot ? This isn't the first time I've heard of people diddling with that plate, and gum'n up the works !

I'm guessing there is a Torque spec on those screws ? Perhaps if it is out of spec, it may cause the top to cantor, or lean to one side, causing the Firing pin to bind ?

Are they brand new mags? If yes then follow the magazine break-in formula. Also, if you haven’t read the instruction booklet, please do so as it has critical information on ammo grain weight usage.

Wasn’t quite like watching paint dry but nice color and good music. Name of song/band if you recall? From a fellow Chicago woodworker

my front sight also fell out. thanks for the info

That catterwallin' noise in the background is a distraction!

My 2020 Chevy, Silverado 1500 Just the same thing and I pulled the f58 fuse and reset the radio and it works fine

I also have a 2020 silverado 1500. The chevy logo appeared and frozen on screen I pulled. The same views talked about there info2, Which was F58 On the Passenger side fuse block. When I restarted the radio with the fuse back in it was fine.

That is a horrible design. I can’t even begin to imagine how anyone could have approved of this concept

Really great Idea. Wish knew about this sooner !

What kind of finish are you putting on it

I know it's been some time now but I would like to get an update on this to see how you like it and how it holds up.

Thank you for this video. Great work. I'm curious what size screws you used on the T-track on the base? Looks like you'd only have about 3/8" to screw into.

This guy's video sucks❤

@Chicagohand so what did you find out? Did u get it fix? I am having exact same issues with mine can you update me on if you resolved the issue

i got my 1964 Delta 34-450 unisaw right tilt table saw running. i just ordered a benchdog router table wing and incra lift like yours. once i get that installed i'm fixin to git the exact 90 miter too.

I had the same issue on my 2019 Gmc 1500 SLT 4x4. Replaced the front pads only on my own. about a 30 min. job, very easy but then I got the same exact message. Front pads wouldn't engage when attempting to drive vehicle. I did put the truck in service mode before doing anything. A buddy of mine with a scanner cleared the codes and all was fine after that. I'm dreading doing the rear, I just ordered of rock auto. I do have a code reset tool off of amazon, just in case. (I can't reset the % on the dash though, I read on forums dealer is the only one who can do it for around $200. I don't know how true that info is though)

Magazine not clip

My bandsaw looks naked next to yours . 😂

Excellent video my friend! I've been looking at making one of these. I will definitely use this video as a reference. I think I will make the first two cuts on this sled and then use the fence. Seems like that would be quicker. Thanks!

A simple straight forward design that is practical that works. Nice. Thank you for presenting this. Looking forward to building one of my own. There are lots of short log pieces needing to be cut that have been stacked up for a couple years just waiting for such a system as yours. Time to get busy. Thank you again. Stay blessed.

I watched this/your video for this log sawing logs and liled it better than any of the other videos on u-tube. Very good and you explained its build and operation easily. Thanks much, I will build myself one.

Considering that 7mm is about .275 inches, a 270 Win should work.

Where did you get thar square bar clamp for holding the log...did not find any on amazon using a tube so it can be fastned to the sled fence...thanks. Great design!!!😊

It would be good to weld some extensions and/or cleats(spikes) to those jaws for larger heavier logs.

Nice

I have a PMR30 & two P17's and Kel-Tec Recommends that You Not take those Parts off and you should not go any further when cleaning. I'm not quite sure that your prognosis is totally correct in this Video and You might Be Wrong! My Fire Pin Broke at about 1000 rounds and I installed a new one but It took me a long time to do this because I'm Not a Gun Smith But I did it anyway. We as amateur Gun Smiths can't always be right and assume we have solved a problem. Good Luck to you in the future with your PMR30 and mine works fine now!

I changed my brakes today and had the same lights come on. Any idea how I fix this? I have a 2109 Silverado 4x

I tried this and blade drift was to bad . Couldn’t use the t slot

That dog bark at 2:44 had me thinking my neighbors dog got in my house somehow🤣

I'm on my 4th firing pin. I'll never buy Keltec again because of this. Great customer service, but what use is a gun that breaks so often. My hellcat has no such issue.