mann! i watched other viedeos they had me ready to do everything from changing the belts up to dropping the transmission. long story short, your video saved me a lot of trouble! there is truth when they say it's the simple things; thanks bro!

thanks.Helpful

Thank you for this great video on installing springs. Thank for the link too 👍🏼👏🏼👏🏼👏🏼

Thank you , peace ✌️

What stock did you use?

I did the same to my civic but I drilled it straight into the bumper looks sick and very bright. It’s also on my channel.

The truth is in the details, the community speaks, I appreciate the comments.

Sweet I been thinking about those too seeing my hood jump around on the freeway is a weird thing only Jeep people live 😮

Why didn't you do the same experiment the same way on both shoes

Worked perfectly. Saved my Bacon!

Thank you for the advice.

Hey man,did u re-gear or are you on stock 3.21?

I think my GSD would jump over it.

these are called Thrust Needle Roller Bearing , good video, never of doing this

The two main problems, with this type of mower is the hard steering and the belt keeps coming off, I finally found the fix to both of these issues that keep happening,, after trying almost everything, and that repair is to purchase a zero turn, it fixed both of the problems instantly, and the problem never came back, it was a permanent repair. 😎👍

Perfect . Great video . Just what I needed👍🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸

I just pulled my mower into the shade to cool off because after I stopped to pick up golf balls littering the yard, it seemed to have half the power up hills even though the tires weren’t spinning and the engine wasn’t dogging down. I figured grass was packed in there, but this wasn’t going to be the first spot I checked.. until now.

God created the world to clean itself, of course you don’t want to INTENTIONALLY pollute the environment like throwing old tires etc. But if that tire is chopped up it will deteriorate over time….everything turns back to dust….just the way it always has. When you pay for a gallon of gasoline you just paid about .60 cents PER GALLON!!!! 3 taxes. 1. Federal tax 2. State tax 3. Local tax. Where is all the money going? Good question!!! It sure isn’t going for FREE recycling!!!! Most people do not intentionally try to pollute, but when the government gets involved now they (businesses) charge for recycling tires. Every time you buy a new tire they charge a disposal fee. So what do the poor folks do? You guessed it….they avoid the recycling fee by taking the old tire home and then chucking it!!! Instead of the government (which the people supposedly run) recycling for free they charge money. There is the problem. Every time you get government involved to solve our problems it never works out.Ever. It’s still WE THE PEOPLE RIGHT?

Nice; thank you

Any follow-up pictures or video for us?

Very good amen 🙏🏻

I've heard of it, now I have the visual. Thx

and a link to the heat shrink

could you or someone share a lnk to order then from

👍🏿

One of THE BEST quick hacks I've ever seen!!!!🤩

You helped me out greatly. Working on a customers e350 with midship single pump. No wiring diagram with the new pump. Our colors were a little different but your vid guided me in the right direction

Your a great teacher! Thank you.

Cars and trucks should have that arrangement; makes the load on your power steering pump or your arms (non power steering) so much less. Also to make steering your mower even better, while carrying your beverage along, do what I did with the landlord's John Deere rider and put a "Brodie knob" on the wheel. for vehicles it would be necessary for the manufacturer ( initial design, fat chance ?) or an owner to do machine work, for needed clearance, to allow a SEALED bearing arrangement to be installed.

There's a reason the machine wasn't designed with these included and ding, ding, ding...you guessed it, debris! Those bearings aren't gonna last any time at all before they fail and lock up. There goes your "hack" smh

Can this be done on a dirtbike tire?

Does this only happen when it was empty? Or did it also happen when filling up on quarter full? I appreciate your response, I'm trying to diagnose my Camry 2018.

Wrap the electronics in plastic walmart bag!

I used a 4 1/2 inch flapper disc (40 grit) on an angle grinder. This will strip that rusty surface down to shiny metal in no time. Use a wire wheel for the perimeter and a small wire cup for the corners. The first time I did this I used only a wire wheel. It was a pain and took a long time. Using the flapper disc cut the job in half.

Absolute A+ for effort! Love the attention to detail.

How bad does that fence stink?

This mod will greatly extend the life of your steering gear and rack also.

The BEST VIDEO EVER!!! 👍👍Well out of the last 4 Or 5 I watched anyway 😊

Once all the air is out do you lock the air valve again??

So you showed doing this to only one side which looks like the slave side and not the side with the steering shaft.. so do I do this to both sides or only the one side like your video shows?

Just tried this and it worked the first time on a Kenmore HE4 unit. Very pleased I found this video!

Good overall video but the fact is; Tire pressure setting is on the door jamb sticker and its defiantly not 38, I believe its 32/30 on that Model Year. That will make a difference in how the VSA module determines whether is getting low based on rotation of the tire

Agree with doing it yourself if possible to avoid being ripped off. Appreciate your helpful videos, good stuff! Thx! ⭐️🇺🇸😎

thanks to the video it took 10 minutes . Thank you!

Do you still have your RSX? Those videos are how I found your channel.

Nice!

Gotta go buy a swivel at harbor freight now 😅

Those look like some really old ventures, like from the late 90s

Truth be told, a slightly higher action sounds better and these modifications shouldn`t be necessary on a well engineered instrument. If you want Les Paul action then play a LP. The benchmark for guitar, is actually the gut string classic instrument itself. If I eat cereal, I choose oatmeal, not Lucky Charms.

⭐️👍😎