To be sure. Manual relief valves are adjusted and set with the vehicle not jacked up?
@mahendraadhikari669413 күн бұрын
Sir please share the kit no.
@EJAZenarosaАй бұрын
👍👍👍
@jagpaldhaliwal1338Ай бұрын
Can you buy this machine?
@biniamtekeste38752 ай бұрын
Where u located u shope
@jeetudav30453 ай бұрын
How we can make this grinding machine, please help and send me details
@expressogino39713 ай бұрын
Look at the replies below, I posted a link to a similar machine. Good luck.
@RellenoHuachanoconcascod-eb9jv3 ай бұрын
What is the size of the plug for the return line?
@expressogino39713 ай бұрын
Depends on the size of the return line on the vehicle.
@arturosardinas35864 ай бұрын
Where can i get that tool
@expressogino39714 ай бұрын
It is Home Made. Easy to make with a little welding.
@user-xb2pz6yz8v5 ай бұрын
به زبان فارسی لطفاً هم همین کلیبر را بزارید
@user-jp8gj3pz5p5 ай бұрын
Thank you !!!!
@user-xv4sy8ic5h5 ай бұрын
u da man
@graffkids13796 ай бұрын
I’m gonna try and create my own plug by using the one where the hose connects to. This will be my mold. So first I’ll lather it with a lubricant like oil(just enough so it won’t get stuck to the mold). Then I’ll put it inside a spray an plastic cap. Then I’ll get a hot glue gun and fill it to where the thread ends. Let dry and un-screw. Now I have my mold. Finally I will lather the inside with a little lubricant (oil) and with the glue gun fill it with glue. I’ll top it off beyond the threading to have enough to later cut for a socket to fit. Oh yeah I’ll make sure and lather the top of the mold w a little bit of oil as well, so the bolt/plug won’t get stuck to the mold when I pour the hot glue. This is for a one time use. No need to tighten. Just hand tight enough for it to hold pressure to pop the seal.
@expressogino39716 ай бұрын
Interesting. Not sure it will work as there will be approximately 2500 psi of pressure on that homemade plug. Just how strong is the hot glue when dried??? Who knows. But, I can't blame a man for trying. Let us know how it works out. Good luck, and be safe incase the plug does not hold.
@jordanrobinson71346 ай бұрын
Did anyone notice that he's wearing a wedding ring and wearing a watch Which both are bad and not to be worn while in a shop doing work I know we all break rules, but it's just funny to see it at a corporate level
@ermaschultz81056 ай бұрын
*promo sm* 😁
@vahagnmelikyan29067 ай бұрын
Trailer kingpin is the most mysterious part for me. How that piece of metal is capable holding entire trailer weight?
@expressogino39717 ай бұрын
Strong, very strong!
@PlayTalkingSelf6 ай бұрын
yes i watch it the Semi truck crash compilation videos... if the trailer falls over it won't cut out the fift wheel
@opmike3438 ай бұрын
Simple, and to the point. God bless you.
@user-phoenix-A69Ай бұрын
Fr!
@chuxsvt8 ай бұрын
What’s the torque spec and the adjusting nut?
@expressogino39718 ай бұрын
No torque spec on the nut. Tighten until the rubber washer has some resistance to turning, and then back off the required amount (usually 1 full turn). Keep in mind this must be done with the lock tester in place.
@abutaherservicemaintenance63749 ай бұрын
Nice video
@user-zv1yu6pn9j9 ай бұрын
❤
@NayomalWijeratne9 ай бұрын
At 1.54 on what are the 5 pieces ? Their purpose? Does it hold the circulating balls in place? What would happen if those 5 pieces loosens? Would it cause steering wheel play?
@expressogino39719 ай бұрын
Yes those pieces hold the recirculating ball guide in place. Never seen one loose, but if it did it won't go anywhere as the top of it will be prevented from coming out because it is very close to the cylinder bore housing.
@codym79609 ай бұрын
which do you adjust to get more cut when turning left / drivers side? the bottom right?
@expressogino39719 ай бұрын
Depends if the worm gear is Left hand or Right hand thread with the power piston. Left hand threaded worm gear, TOP. Right hand threaded worm gear, BOTTOM. This is for standard mount boxes, output shaft on the bottom side of the box. Reversed for inverted boxes, output shaft on the top side of the box.
@codym79609 ай бұрын
@expressogino3971 yea mine ended up being thr bottom . Not sure how many but I think it had to be at least 10 turns to get full travel
@shahbazpathan389ify11 ай бұрын
good job 100% worthy.without wasting time job done
@brokengamer303411 ай бұрын
ZF72..steering box
@thebaycuddy Жыл бұрын
Plungers help with hard steering?
@expressogino3971 Жыл бұрын
The plugners will open and reduce hydraulic pressure in the last 1/2" of wheel travel towards full left and full right turns. If the plungers are not set correctly or don't work the system pressure will reach the pressure relief setting and may cause damage to steering linkage components because of the high forces. When plungers are working correctly the pressure will drop at Least 400 psi below relief valve setting. So if the relief is set at 2600 psi, just before full wheel cut to the left or right the pressure will be 2200 psi or lower.
@dchawk81 Жыл бұрын
Anyone know the part number for the seal under the head that the 4 bolts around the shaft retain?
@andrewm5190 Жыл бұрын
Does this adjustment help with Poppet valves
@expressogino3971 Жыл бұрын
Not sure what you are asking, but Poppet Valves and Relief Plungers are the same thing. TRW - poppet valves. RH Sheppard - Relief Plungers. Hope this helps.
@carlosvilla1140 Жыл бұрын
Thank you
@ArvindKumar-eq9wt Жыл бұрын
Superb
@user-jr8lf6pl2m Жыл бұрын
Can somebody explane, whats mean "the chassis should NOT FLEX"?
@expressogino3971 Жыл бұрын
When the steering is turned full right or full left the frame/chassis should not twist/flex. Raising of the frame rail is normal as it goes through it's turn because of the caster angle. If the relief plungers are not set correctly, hydraulic pressure may reach max pressure at full turn, putting extreme stress on the steering linkage components and causing the the chassis to flex/twist.
@user-jr8lf6pl2m Жыл бұрын
Thank you very much for explaning this special term! By the way, your videos about M100 helped me repair and adjust steering gear on my Inter 9800. Thanks for that too and good luck in all your ways!
@luiscarlosmolinaduran724 Жыл бұрын
buenas tardes como se puede regular el desgaste de la quinta rueda si no trae el.perno regulador al costado
@markco4911 Жыл бұрын
The Best!
@quesodagod8840 Жыл бұрын
I used a socket
@Oldschoolgamer6439 ай бұрын
What size ?
@jt48967829 ай бұрын
That’s what I want to know
@skybordage3817 Жыл бұрын
You can call kingpin specialist for any needs related to your kingpin being worn down or not within the proper specs
@expressogino3971 Жыл бұрын
Yes, they also do this type of work.
@rizwantarar4208 Жыл бұрын
What is the size of the plug
@expressogino3971 Жыл бұрын
You will need an "O" Ring hex plug as seen in the video. Typically these are -8 (dash 8). Have on hand a -8 and a -6. These two will fit most boxes. If different then you will have to match the plug to the fitting size. Hope this helps.
@mikeyroche5979 Жыл бұрын
Just wondering what you call or what type of machine is been used to grind the pin after building? Based here in Ireland and havnt seen or can't find any information on that type of machine. Is it something that you made or is it a type of thing that can be purchased. Any information would be kindly recieved. Thanks.
@expressogino3971 Жыл бұрын
Hi Mikey, not sure the correct name of the grinding machine. It does look like a homemade unit. I doubt that a company would make these as the demand would not warrant the R&D to manufacture these. You could probably make one. If you decide to make one. let me know. I would love to see it. Good luck.
@expressogino3971 Жыл бұрын
Just did a quick search and found an early patent on said grinding machine. Take a look. patents.google.com/patent/US3106807A/en
@s200064 Жыл бұрын
Where are you located how much does it cost to get a King King refurbish is it better than getting a replace really good video thank you
@expressogino3971 Жыл бұрын
I'm in Canada. This service is available throughout North America. Just google search "Trailer King Pin Repair" and call one of the companies that provide that service and ask for price and timeline. Hope this helps.
@jordanhoesley1901 Жыл бұрын
Watch your video. Did an amazing job I didn't know people provide that type of service What do you charge to do a job like that? Thanks Jordan
@expressogino3971 Жыл бұрын
Hi Jordan, I don't do this type of work. This video just shows that the trailer King Pin can be successfully rebuilt back to specs. It would take two to three hours approximately to do. Their are companies out there that do this type of work. King Pin rebuilding. If you need that service just google it in your area. Thanks for watching.
@artianrika83292 жыл бұрын
thanks
@expressogino3971 Жыл бұрын
No problem
@alexisdelgadillo80172 жыл бұрын
What size is that high pressure fittings
@expressogino39712 жыл бұрын
You will need an "O" Ring hex plug as seen in the video. Typically these are -8 (dash 8). Have on hand a -8 and a -6. These two will fit most boxes. If different then you will have to match the plug to the fitting size. Hope this helps.
@TheThezeketheman2 жыл бұрын
How do you bleed the air from the system
@expressogino39712 жыл бұрын
Here watch this video. kzfaq.info/get/bejne/n7qDZrd616fPon0.html
@edenfieldjared02 жыл бұрын
can you tell me a part number for the seal installer tool please?
@expressogino39712 жыл бұрын
OTC Kent-Moore J37073 Input Shaft Seal Installer Tool