confusing explanation vs. his "drawing"

Great video! Thanks for the information

Everything has a science to it..

Thank you so much for sharing. This video is so helpful. I am wondering if you have online courses for teaching new students in cananda ?

I wish they had videos of people going over plumbing code

Awesome! Just completed my assignment and used your video as references for my mistakes, thanks again Edward!

Great video Edward! Im working on writing my CFQ and this definetly helps with the visuals! Subscribed. Which building code do you refer too in your videos? Im currently working under the OBC

Excellent video. Thank you

I believe you got confused a bit, although in theory yes you do want a slope on those branches leading up to the wye T, when you add an off set like that 45 you are exceeding the fittings purpose. In other words if you had a branch glued directly to a wye you could only slope a certain amount in order to glue them together without causing a leak, therefore the wye fitting could be slightly sloped but not enough to break the plane. Picture a combo wye, if you would have used one it is still limited to how much you could rotate it. Maybe you meant to do it maybe you didn't but you created your own combo wye, that was really the problem. I hope this made sense. And for those saying that it would siphon the traps, it's really more about waste water running faster than the actual waste and the branch not being properly washed.

I never would have guessed gutters and downspouts would fall under plumbing design. 😮

Dangit, i really hope you're still teaching somewhere. I've been soaking up you're videos for the past few hours and you have impressed me. I imagine you've got a pretty good rating on Rate My Professor. 😊 My youngest is currently a freshman in college. Her trig teacher started the first class bragging about his 30% pass rate and told the kids to not with of they get a bad grade in his class because after they graduate it won't even matter. If I didn't work at the very same university, I'd have paid him a visit already. This is where tenure fails us...

3:37 i had to back track to hear what you said because I read the formula as A=offset÷advance...

This was a fun problem.

I can't think of any reason I will need to calculate anything like this. I watched the video simply for the joy of learning. I understood it right up until 9:19 when it comes to calculating the length of B,E,H. Where do you get the "Offset" number? The term offset is used throughout the video, but i don't think it's defined. Also, right in the last few seconds you introduce the term "Advance" without defining it. It appears these videos are too supplement what you taught during an in- class lecture, so perhaps your target audience is already supposed to know those terms. I've been enjoying your series of videos. I landed here because I'm redoing plumbing that a "handyman" did during a bathroom remodel. There's a veritable plethora of code violations from horizontal hard 90° turns, Sani-Tees lying on their back, and S-traps under the sink and tub. Good times.

The previous video with the narration made much more sense than this one! 😅

14:41 you mention two 45° need to be separated by 12" of pipe in order to make a 90° horizontal bend. Does the distance requirement between the two 45° change depending on pipe diameter? Or is it 12" for any dia pipe.

on a very very large scale application, how do you plumb for far distances given the supposed curve of the earth??

How would I do an isometric of a 2 story with 12 fixture units to scale?

Hey Logan I’m working on a project with Parallel off sets and a few other offsets i have most of it down but I’m confused on a few other parts as they only give you so many measurements, If theres anyway you could help me i could send you the plan and what i have so far- thanks

Cud i use a double y upside for venting?

Could you do a drain plan of a bathroom etc

I appreciate that you've covered most all the different fittings. I was concerned about the sweeping wyes and the siphon effect. Something that might be helpful on your diagrams is to show the viewing direction of the fitting installed drawings on the stick diagrams.

🔥

Thank you!!!! I wasn't sure whether to buy a T or a sanitary T. You answered my question!

👎👎👎 I boo your video sir

I appreciate this sir!!

CROSSTHREAD ED

waaaay too close for comfort

Thank you.

This is extremely helpful! My wife and I are turning our first floor closet into a half bathroom but we just failed our plumbing inspection because we used the wrong fitting - should have used a wye instead of a ty. It all makes sense now after watching this. Thank you!!

Is there a way to download this document?

Do u have a document u can share?

Painful

Is this IPC OR UPC?

God bless you, sir. Just a perfect video of the exact info I 2as looking for!

Nice 👍

Is it proper to lay the gravel bed first, then the pipes, or to lay the pipes first on earth, then the gravel bed, before pouring concrete for SOG/Flooring? BTW, thanks for the video. I learned a lot from it. More power to you, Sir.

Hello Edward I know you are trying to people like me trying to fill this kind of documents but in my opinion if you write down in sheet wherever you saying that will help a lot try to make an template the will help more thank you for you time

Awesome

your channel is my favorite for plumbing knowledge. thank you!

please provide download document

This formula works for threaded and socket as well eh

Hi Edward... Please can you help me solve or know how to solve problems or real situations of take off in threaded joints. For this examples: 1) A piece of NPS ∅2" pipe is being cut to run between two 90° degree threaded fittings. The center-to-center measurement of the fittings is 7'-2¼". What is the cut length of the pipe? 2) A length of NPS ∅1½ inch pipe is to be cut run between two 90° degree 6.000# threaded fittings. The fittings measure 7 ft 2¼ inches center to center. What is the cut length of the pipe? What fittings tables do you use to obtain the dimensions required for the calculations. Regards... Thanks

DUDE WHERE IS THE CALCULATIONS? DID YOU MAKE THIS VIDEO TO HEAR YOURSELF TALK?. WHAT KIND OF TEACHING IS THIS ?

Does it still work when both pipes are in the air and not close to any walls ?

Isn't TE also provided by the fittings mfg, ie. Ward fittings has a PDF doc with all of the center + thread measurements. Wondering if that's the same?

thank you this was awesome

Sir , This information very useful for me ,, thank you sir .

This is known as takeoff

This is known as takeoff