10 ай бұрын
10 ай бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
3 жыл бұрын
Пікірлер
@privatecan 8 сағат бұрын
Hello2 I will think buy TWH cylinder 50MM to Honda dio Af27. What you think about this process. My everyparts is normal Honda. It’s okey? That’s Dangerous? (try to answer :)
@saimonemafi434 13 күн бұрын
What makes it a stroker the crank part???
@n4smotorwerx 4 күн бұрын
Yes anything bigger that 44.4 usually is considered a Stroker
@reyparrocha8432 Ай бұрын
what gearings sir?
@n4smotorwerx Ай бұрын
I use a variety of gears depending on what pipe I'm using and what distance I'm racing at. Every motor is set up diffrently !
@wickedmanezy6931 Ай бұрын
Your dio is Definitely slow asf when I rev my Honda dio shit wanna take off to the sky your bike needs way more cc for a stretched dio 125cc atleast what’s that a 50-70cc 😂😂
@n4smotorwerx Ай бұрын
Haha yeah it's slow 7.9s@82 1/8m 13.5@92 1/4m Anytime you want to post your time slips , please do! I'm sure the world wants to see.
@dutchmastertextdutchmaster9617 Ай бұрын
are you tuning it with the laptop with jiso cdi?
@n4smotorwerx Ай бұрын
That's the best way to tune your timing curve :) I use jiso and a few other boxes that are similar .
@sigcroan 2 ай бұрын
❤❤
@808702Connect 2 ай бұрын
motor oil?
@n4smotorwerx 2 ай бұрын
Gear oil :) but I would assume engine oil would work. It's easier to use the gear oil since your going to use it :)
@808702Connect 2 ай бұрын
Aloha!🤙
@yanb1981 Ай бұрын
nice trick! 👏
@kody5779 2 ай бұрын
What does this accomplish
@n4smotorwerx 2 ай бұрын
Better flow and breathing of fresh fuel mix. A Honda block is very inefficient in flow, a terrible design.
@kody5779 2 ай бұрын
That's awesome, how deep roughly did you cut? I've got a couple Sym dd50 engine I'm going to cut for 120cc
@johnehlenberger1145 2 ай бұрын
DOPE bike🫡😎💯🙏
@n4smotorwerx 2 ай бұрын
Once I get it back running it will be lol!! Thanks !!
@MonifrmTheBlocc 2 ай бұрын
So fuckin sexy😩
@n4smotorwerx Ай бұрын
Hahah I need to make it go faster!!
@kody5779 2 ай бұрын
Is that a honda dio arrow exhaust?
@n4smotorwerx 2 ай бұрын
Yes it is ! I just repacked it for him. It was so dam loud hahaha
@aidanambrose4447 3 ай бұрын
Building the same bike right now! USDM Honda spree with eve panels and variated AF05 swap. Stretched and low ruckus front forks/tree. I wanna see more!
@n4smotorwerx Ай бұрын
Spree frames are always fun to build! I have a spree smile as well that I built many moons ago. Only issue I have is the ride is harsh lol! Hurts my back!
@yessahblessah9902 3 ай бұрын
What kinda rpm’s you seeing on the top end?
@n4smotorwerx 3 ай бұрын
I try to target around 11.8/12k anything more it doesn't go faster it's pretty much piss revving ;). Drag strip tuning and street has its similarities but it's way more different than many think. You have a set distance from a dead stop to go as fast as possible unlike street roll racing it's a total diffrent style of tuning :)
@yessahblessah9902 3 ай бұрын
@@n4smotorwerx you running 1/8 or 1/4
@n4smotorwerx Ай бұрын
I have run both , usually just fool with the 1/8 since the 1/4 takes a diffrent time and gears .
@codyeditsroblox 3 ай бұрын
hella yeah brother +1 sub
@n4smotorwerx 3 ай бұрын
Thanks and Aloha!
@gewrecker0877 3 ай бұрын
Can I use 43.2 Twh crankshaft without trimming the case
@n4smotorwerx 3 ай бұрын
Yes, sir! I prefer to use that crack over the 44 just because the timing is a little better. You might have to trim the base of the piston a little bit for clearance on the downstroke.
@gewrecker0877 3 ай бұрын
@@n4smotorwerx I think that I want to get the 43.2 and the athena 72 and I won’t have to trim anything
@adamcopper5688 4 ай бұрын
Will the exhaust pipe off af18 fit on to the sym dd50 ?
@n4smotorwerx 4 ай бұрын
Yes sir!!
@adamcopper5688 4 ай бұрын
@@n4smotorwerx nice.. thank you
@jacksonanderson4771 4 ай бұрын
Looking amazing 🔥
@n4smotorwerx 3 ай бұрын
Thank you 🙌
@Samodel 4 ай бұрын
👍
@n4smotorwerx 3 ай бұрын
😎😉
@MrJermbob 4 ай бұрын
Badass. I want a ride :)
@pezunastuning 4 ай бұрын
hello 44mm crank fit complete with polini corsa ;
@n4smotorwerx 4 ай бұрын
I always love using a mini stroker crank with a Corsa set up, it creates a little more torque, which really helps for going up heels and also if you're a little heavier of a rider
@nickfarri 4 ай бұрын
Aloha, in my other comment I asked for your favorite mani, you mentioned they are quite the same including the stage 6. I have the stage 6 but the flow of this one is much better. In the stage 6 I had to fill ( the first part) with filler and then give it a cylindrical shape to the reed valve. Second, it's difficult to fit air filter because of the skock. The connection with the carb should be more angled. With this one is the carburator more "outside" compare to the stage 6? Mahalo again from Italy
@n4smotorwerx 4 ай бұрын
So the stage 6 top sits straight back , if you use a Twh one , that has a slight outward angle. All my intakes I had shape . Again they are all a copy of a copy. Stage 6 is a copy of a KRS or koso racing . The others are a copy of a CT brand
@nickfarri 4 ай бұрын
@@n4smotorwerx ok thank, you next engineI I'll try the TWH, hope there is no filling and shaping needed
@n4smotorwerx 4 ай бұрын
Aloha Nick, I got up this morning and thought that I should tell you that you could use a chrome intake top with the stage 6 reeds :) I know they stick out sideways and they are cheap to get! Hope that helps!
@nickfarri 4 ай бұрын
Does it need to be shaped inside or is cylindrical inside? I thought I've read you are not a fan of the chromed one. Mahalo
@nickfarri 4 ай бұрын
What's your favorite intake/manifold? Brand? Which one is this one? Mahalo
@n4smotorwerx 4 ай бұрын
Honestly they all are the same. China made, even stage 6 is China :) Main thing is to check its flatness, because they are all not truly flat! Major causes for air leaks especially the Stroker ones . I don't use the chrome ones because they are made really cheap and they use a 3 petal reed which I dislike:)
@nickfarri 4 ай бұрын
@@n4smotorwerx I reply to another of your video
@E-Brazy 4 ай бұрын
what kind of manifold is that boss?
@n4smotorwerx 4 ай бұрын
My own.. I used diffrent parts to make it work
@TheTca211 4 ай бұрын
What the heck am I looking at.
@n4smotorwerx 4 ай бұрын
Hahah!! It's a case splitter tool ! Cant be pounding on cranks!
@TheTca211 4 ай бұрын
@@n4smotorwerx I'ma need to look this thing up lol. I can't tell by looking at it if I'm not understanding the mechanism or because something isn't right and idk the thing I'm just confusing myself into a circle lol.
@TheTca211 4 ай бұрын
@@n4smotorwerxoohhhh ok It separates the halfs that makes way more sense then me wondering how this thing is going to spin lol
@n4smotorwerx 4 ай бұрын
Yeah you don't want to pound on any crank unless it's broken, stripped , throw away!
@user-mh3rz2gn8g 5 ай бұрын
Can you tell me number of main jet that you put on cylinder kit 48mm with stock’s carburetor?
@n4smotorwerx 5 ай бұрын
Stock carb, 85-90 jet
@BUZZLIKER-2507-_- 6 ай бұрын
Aloha my friend i have a question about a polini contessa kit with number119.0077it fits on a af 16
@n4smotorwerx 6 ай бұрын
Yes they do ! Contessa is the non race version of the Corsa
@BUZZLIKER-2507-_- 6 ай бұрын
@@n4smotorwerx thanks but it fits nicely in the af 16 engine without new crankshaft? because I've seen some videos where they upgrade the af16 engine from 50cc to 70cc and don't put new crankshaft
@n4smotorwerx 4 ай бұрын
Most people will upgrade the stock crank with a aftermarket , but if your on a budget the stock crank will handle :)
@THE_UNKNOWN_ARTIST27 6 ай бұрын
Is there any places were it's easier to find parts to sym dd 50 in denmark
@n4smotorwerx 5 ай бұрын
You can used af18 parts on the Sym block
@koppanysztankovits4964 6 ай бұрын
Hello. I want a twh 54mm cylinder with a 44mm crankshaft. Isit possible to run? It will be good? Thanks, nice video!
@n4smotorwerx 6 ай бұрын
Won't work, 54mm is designed for a 52.6 crank. You still need to cut the bore so you might as well cut it for a bigger crank too!
@koppanysztankovits4964 6 ай бұрын
@@n4smotorwerx Ohh okay. Then i will ordar a twh 50mm cylinder with a 44mm crank. This is good or not?
@RichFife 7 ай бұрын
What's the bore and stroke?
@n4smotorwerx 7 ай бұрын
52.6x56mm
@RichFife 7 ай бұрын
@n4smotorwerx Thank You... I've been watching the drags with those scooters... its insane!
@n4smotorwerx 7 ай бұрын
It's just fun things to do :) Cheaper than building a car lol
@RichFife 7 ай бұрын
@n4smotorwerx yessir... I'll be building a custom chainsaw, using the DIO cylinder, head, piston, crank... Reeds and either a Mikuni, Keihin or Nibbi carb... then I'm onto building another racecar. Lol
@everydrift4772 7 ай бұрын
muffler⁇
@n4smotorwerx 5 ай бұрын
Custom made
@2wheels620 7 ай бұрын
Which crank are you using?
@n4smotorwerx 5 ай бұрын
43.2mm Twh mini crank
@user-nr4re9zw1i 7 ай бұрын
How much does it cost me to make this bike?
@n4smotorwerx 7 ай бұрын
Hit me up on my FB or IG !
@ReyEpifanio 7 ай бұрын
Saan po nkkbili ng head at blocke ng 50cc dio2
@dim848 7 ай бұрын
hello, what gear is you use for dio 125cc with 25whp?
@n4smotorwerx 7 ай бұрын
Gearing all depends on the distance your using it for ;)
@ezclapz650 7 ай бұрын
What extension you using that screws into block?
@n4smotorwerx 7 ай бұрын
Came with the tool :)
@PapaRazaa 7 ай бұрын
Totally skips wetting the tires and does a monster burn out 💪🏾
@n4smotorwerx 7 ай бұрын
lol you should have seen the time the throttle got stuck and I flipped over haha No video :( if I had that I would have posted it !
@PapaRazaa 7 ай бұрын
@@n4smotorwerx bro, that kind of reminds me of Rich from Pinks lol. He was looking all “bad ass” hopping on the motorcycle and then totally whipped out lol
@MiniMotozinc. 8 ай бұрын
Yeah for real, I wanna make one for my bike
@n4smotorwerx 8 ай бұрын
I seen a help build a few for low rider bikes before :)
@user-fn1ey3sq4h 8 ай бұрын
What material did you use to make mount round tube and what else how did yu make eyelet to mount to frame and the motor ??
@n4smotorwerx 8 ай бұрын
You carefully cut up your old mount :) The shock strut is a 1in thick walled black iron pipe. Over kill but that's all I had around the shop
@user-fn1ey3sq4h 8 ай бұрын
@@n4smotorwerx is that 1 inch od or id
@abaited 8 ай бұрын
did u need to switch the tree in it for the headlight housing or did the stock one work? Was thinking about getting the same for my elite
@n4smotorwerx 8 ай бұрын
This head set fits with the correct handle bar :) you can also relocate the tabs on the stock bar to make them work as well!
@abaited 8 ай бұрын
@@n4smotorwerx sounds good , appreciate the help sir
@n4smotorwerx 8 ай бұрын
Anytime! It's a lot easier to find the head piece than the correct bar. Relocating tabs are easier if you can do them!
@Hellsbells360 8 ай бұрын
Good on ya mate
@n4smotorwerx 8 ай бұрын
😎👍🏻
@jeningrassia9541 8 ай бұрын
Nice work, and great music!!!
@n4smotorwerx 8 ай бұрын
Thanks and Aloha!
@FWMjokivity90 8 ай бұрын
what in the redneck meth heads stolen parts and tools is going on around hee
@keliiwoffordjr.1097 9 ай бұрын
Uncle it sounds so perfect 😢
@n4smotorwerx 8 ай бұрын
It's running like a champ! Not built as a fast roll bike! Still needs alittle tuning but it does 70 pretty easy with this pipe :)
@kepoo808 9 ай бұрын
This is one of my favorite combos corsa and a mini stroker such a reliable set up💪🏽
@n4smotorwerx 9 ай бұрын
Couldn't agree more! It's one of my favorite builds for my customers !
@jrmayol857 9 ай бұрын
We'll wait for the videos of the build process 🤩
@n4smotorwerx 9 ай бұрын
Just finished up the porting of the Corsa today :)
@jrmayol857 9 ай бұрын
@@n4smotorwerx when will be the upload? Looking forward to it
@fernandocruz-rw5wl 9 ай бұрын
Af16?
@n4smotorwerx 9 ай бұрын
Yes it is!
@user-cf3cv9nc2o 9 ай бұрын
😎🔥🔥🔥👍👍👍
@user-cf3cv9nc2o 9 ай бұрын
😎Красава 👍👍👍✌️
@n4smotorwerx 9 ай бұрын
Thanks and aloha!!!
@fernandocruz-rw5wl 9 ай бұрын
Es un af16?
@n4smotorwerx 9 ай бұрын
Yes it is;)
@runningbear211 9 ай бұрын
Hey have you ever ran nitro in one of your bikes
@n4smotorwerx 9 ай бұрын
Ran a wet set up of nitrous about 15 years ago. I used the smallest jets and it was like 18mph faster . But there's used to freeze up constantly . Only way i found that they would last is from the outside like in an air filter or velocity stack . Still they freeze and break but at least you'll get a few runs :)
@runningbear211 9 ай бұрын
@@n4smotorwerx I'm talking like nitromethane the fuel they use for the rc cars
@n4smotorwerx 9 ай бұрын
I always get offered to use it but never did. Tried Rc fuel And honestly it didn't even change . I think the percentage wasn't enough. You need very high compression as well as a good ignition system.