How can I order this?

great ty from the Philippines

I love this video. I couldn't have threaded the machine without it! the little diagrams are not sufficient. Thank you for all the little tricks and thorough instructions.

Pls which one is good between them

Wow can't believe a girl just taught me this 👏🏽

Didn’t realize how big your guys yard was.

Do you happen any information on how to service a babylock BL4-738

Where did you buy them with the handle?? I can't find them in Amazon in that size with the handle. Please provide link.

I was thinking about you the other day! I think this is the pool my neighbors have and they love it. They are in it all summer long. Going to be 97 today. They'll be in that pool!! Thanks for the video, Irah! Hope everyone is well!

Thank you! :)

that case is way to big to be a mico holy cow i have a micro atx build and that would not fit on my desk like my current build

Thanks

I need help i took apart the machine and the 4 metal peices came off to latch the thread on top but im not sure how to put it back together

Super brest loveyou daling 🌹🔥🔥♥️

Very helpful.

how do you know what the correct thread tension is and how do you increase or decrease?

I don’t understand this video. It’s the worst she doesn’t show you where to place anything everything is cut out like the lower looper or where to put the thread guards down at the bottom now that it’s taken apart I have no clue where to put them back.

You are one awesome beauty you are a fantastic mother to your kidd's

I love big milk woman chest

hi

❤

Amazing video thank you! How often to you change the oil? The book says 4-5 months I believe but the guys told me every 2 years ?

This seems like a 'fast as possible' guide for preventing your serger working correctly. Please if anyone reads this comment, find a different video to follow when attempting any serger repair.

Did the lisp go away? I'm a little nervous about it. This is the second video I've watched of someone having speech affected. I am doing daytime aligners.😅

Can you help me to fix singer serger timing ?

Thanks

Question: my serger sews a few inches then quits, it will restart again if you turn the hand wheel a bit, but only for a few stitches at a time. Motor shot?

Sobrang ganda Po. Pero Hanggang parangarap nalang ako 😢 hindi ko kaya bumili ng ganyan kamahal na breast pump.

Mine doesn't have center holes in each slat. Just a notch on the bottom. How do I replace one of those?

Great video but not helpful without the lower looper position

Do you have a video on adjusting the tension?

😂😂😂😂

Nice chi chis

i'm not sure if 70% of the comments are confusing Micro-ATX with Mini ITX or what. but this is a typical Micro-ATX chassis. not ATX. try putting an ATX mainboard in a case that only has 4 PCIe brackets worth of vertical space and find out what happens

need change filter too

🤤

Very enlightening video

if you adjust your needle bar height, and it's not the part that slipped (it rarely is), now your needle and feed dog timing are no longer in sync, the fabric might be moving while the needles are still in it. This will also mean your cutter is not in sync with your needle timing too, but this isn't the primary issue. Try not to play with the needle bar height to make adjustments to timing. Also, it really helps to know your clearances. Where are the loopers supposed to be when the needle bar is top dead center or when the needle is just at the height of the needle plate (use a sheet of paper where the fabric would normally go to determine this.) This is a good explanation though. A fix more than a repair though. Also, damn you're using a whole ass drill just to take off these little tiny screws. Get some stubby ratcheting drivers or something. At least get a little subcompact impact driver or something.

I love This but if you could do it with four different colored threads, that would really help me know what you're talking about

😢I’m in so much pain day one sucks 🥹😭😭😭😭

I panic clean when my husband is on the way home all the time. I can totally relate 😅

Thank you for sharing this information 😊

"Warning: If you buy this DeWalt Pressure Washer product in the Los Angeles Area you must travel to Ontario for service under warranty. My unit's telescoping handle broke after 6 months, so it is not easy for me to get it repaired under warranty as the service center is 1 hr away.

"Warning: If you buy this DeWalt 2100 product in the Los Angeles Area you must travel to Ontario for service under warranty. My unit's telescoping handle broke after 6 months, so it is not easy for me to get it repaired under warranty as the service center is 1 hr away.

That aint micro😂

Where is the location of the oil filter, I thought you were going to change the oil filter.

Hola buenos días, I got the same machine yesterday but the tendon is of mostly the upper loopers . How can I fix it and adjust to to the right tension.

Hi, You mentioned that you could do the hard work and mail a kit to us. How can I get that done? Thanks

Silicon Oil? Is that different than the DEFRIX Oil 1 that it comes with?

Thanks for sharing