thank alots

Thanks alot

❤

Looks interesting. The videos are so short for such a course. If you can remove the background music; this will make it better to understand the concepts.

Very good!!!

Hi I'm from the Philippines, I wanna know the difference between ampere trip and ampere frame of the circuit breaker ...thanks and more power.

❤

Thank you for the accurate and educational video

Brilliant video, thanks a lot.

👌

Great 👍 ❤

Hi, in the example, the TV is rated 150 watts so consumes 150 watts of instantaneous energy, does this mean 150 watts is consumed every second that the TV is on for?

Excellent 👏🏾

It has its advantages too where the ash particles from the boiler are ionized and use the hammer to lower them to the ash tray where they can be removed from the boiler. In power generation

Excellent pro ❤❤👏💪

Could you add a dimmer?

Hello i have a high pressure sodium lamp. i can't use it anymore because if i put a new bulb it blow the bulb. can u tell me what is the reason of burning out the bulb?

Nice explanation

clear and simple explanation, thanks a lot

我的擅长

faults in the oil ? the bucholz relay senses gas accumulation caused by a fault in transformer windings between windings or a dead short circuit the gas produced by this faults are accumulated inside the bucholz relay and this gases actuating floats the floats ativating a alarm aswwell turning off the faulty transformer through safety devies explain it right thank you

how do I know what capacitor size to use?

Can I use it for low voltage wires and devices like 12VDC and 48VDC?

Just for the files: Face masks won't protect you from Corona discharge! 🤣

You assume P is constant for before and after situation but actually is the S constant - P is changing with the Power factor changing

You know your motors, thanks very much for a great channel.

What a peculiar accent

if we find the power again, what is the first thing for?

So if the nameplate of a motor shows 100W, power factor and amperage rating. Is that 100W just the active power and not the apparent power? This subject has always confused me but your videos are helping me understand things a bit better so thank you.

good job

How much voltage does it take? (Please answer 🥲)

Hence Covid 19 now the vaxed carry the payloads hence the noises they emit on ham Radio. Balancing payloads on persons as persons have no human rights. You all best fight for the right to be human then worry about rights.

As shown in curves it take a specific time to trip, moreover why we are choosing the MCCB rate current to be equal 1.25 full load? As example: heater current = 12 Amp MCCB ==> B16

kzfaq.info/get/bejne/mql2h8ynlrbOd6s.htmlsi=mk9v4dviKPvJBUYX Why Power is three times more in delta than star connnected load. Subscribe KZfaq channel

Where do you buy that contractor you illustrated?

Very helpful!

Superb explanation!!!

leetcode?

Why there was no operational symbol on the second mcb?

کمک های معیشتی

Engineering is never boring.

valuable information thank you

3 phase how to install in 2phase

In the explanation you mixed up X2 and x3

Thanks for your clarity in delivering the issue I am expert in this field however I shifted to another field and now I am back trying to catch up; you brushed out a lot, well done. I have one question why in the switch example you tested it while the switch On ? is it safe?

What is the difference between 3 wires and 4 wires for a PT100 ?

Weldon, your explanation helped.

In reality the 100 bulb is brighter

*The cost difference really adds up if you are ordering quantities of 50 to 100 or most obviously, 1000 each in a wide variety of values. I also greatly dislike working with 1/8 and 1 watt resistors. In a lot of D.C. circuits, 1/8 watt are perfectly fine, but if you are using perfboard, I personally find them unpleasant to work with.* Installing 1/8 watt on a PCB wouldn't be a significant hassle, but I would personally still dislike using them.

So a C16 MCB will keep working if 16amps current drawn by a AC stabilizer (100% rated current load @ 230 volts ) runs through it day n night 24*7 ( in case of inverter AC ) & will only trip when amps exceed 10 time the rated amps (short circuit ) or voltage drops ( below 200 volts ) and AC stabilizer starts drawing more amps causing overload situation right ?