So the setup require XLR cables, and no longer wireless?
@Toyrapy4 күн бұрын
Hi, thanks for your awesome video. I have 2 EON 715 + EON 718S, and mixer MackieProFxv3+. Both speakers and mixer are bluetooth, should I send music from my computer to the speaker or to the mixer. And your advice on the best way to run minimal cables between the units so that I can utilize the wireless bluetooth function please. (Setup intention is for Karaoke). Thank you!!!
@NicolaX-bo2dn5 күн бұрын
Good evening I have a question I could connect 4 715 and 2 718s together in a dj console?
@marlonwilliams492712 күн бұрын
Your going way to fast I can’t follow you, I’m very green. Thanks for the video though
@alexc223418 күн бұрын
Great videos. I just watched two of your vids on this sub. Any reason you connected inputs to mains on Ch2 rather than Ch1? Also why did you select Full Range rather than Sub? You didn't explain why?
@MiswarSaputraBurhan21 күн бұрын
How to set up 4 Pcs PA 15 JBL EON 715, 4 Pcs JBL EON 718S Subwoofer with Mixer ?
@jblsoundbiz19 күн бұрын
Hi, thank you for your comment. This is a good question. You can try to install a PA system by using the four methods below. Method 1. Using four EON718S subwoofers in cardioid position and placed in the center facing the audience while the EON715 position is placed left and right (2 left & 2 right). Method 2. Using two EON718S subwoofers in a cardioid position placed on the left and right together with the EON715 (2 tops + 2 subs on the left and 2 tops + 2 subs on the right). Method 3. Using the two EON718S subwoofers not in cardioid position placed on the left and right together with the EON715 (2 tops + 2 subs on the left and 2 tops + 2 subs on the right). Method 4 Uses two subwoofers in cardioid position and placed in the center facing the audience while 1 subwoofer is placed on the left and 1 subwoofer is placed on the right together with the EON715. However, the method of installation of this PA system depends on the location and atmosphere of the event at your venue. You can choose any of the above methods and I will explain how to connect the cables from the mixer to all the speakers. Please support my KZfaq channel by subscribing and clicking the LIKE button on this video. Thank you and have a great day! 🤗
@MiswarSaputraBurhan18 күн бұрын
@@jblsoundbiz instal cable Chanel & Pass Thru
@MiswarSaputraBurhan17 күн бұрын
Make Video tutorial please set up normal or set cardioid with mixer use 4 pcs Jbl eon 15 and 4 pcs Jbl eon 718, simulation
@jblsoundbiz16 күн бұрын
@@MiswarSaputraBurhan Hi, thanks for replying to this comment. I am happy to make a tutorial video for this kind of PA System setup, but I don't have enough EON718S, I only have 2 pcs. For EON715, I already have 4 pcs at the moment. But don't worry, I will make a tutorial video for 4 pcs of EON715 speakers and 2 pcs of EON718S Subwoofer in the next video. So, stay tuned and subscribe to my KZfaq channel for the next video. Thank you so much for your support and have a nice day! 🤗
@MiswarSaputraBurhan15 күн бұрын
@@jblsoundbiz U Have instagram ?
@MiswarSaputraBurhan27 күн бұрын
How to set up 4 PA 15, 4 Subwoofer ? 🙏🏻
@jblsoundbiz19 күн бұрын
Hi, thank you for your comment. This is a good question. You can try to install a PA system by using the four methods below. Method 1. Using four EON718S subwoofers in cardioid position and placed in the center facing the audience while the EON715 position is placed left and right (2 left & 2 right). Method 2. Using two EON718S subwoofers in a cardioid position placed on the left and right together with the EON715 (2 tops + 2 subs on the left and 2 tops + 2 subs on the right). Method 3. Using the two EON718S subwoofers not in cardioid position placed on the left and right together with the EON715 (2 tops + 2 subs on the left and 2 tops + 2 subs on the right). Method 4 Uses two subwoofers in cardioid position and placed in the center facing the audience while 1 subwoofer is placed on the left and 1 subwoofer is placed on the right together with the EON715. However, the method of installation of this PA system depends on the location and atmosphere of the event at your venue. You can choose any of the above methods and I will explain how to connect the cables from the mixer to all the speakers. Please support my KZfaq channel by subscribing and clicking the LIKE button on this video. Thank you and have a great day! 🤗
@MiswarSaputraBurhan17 күн бұрын
@@jblsoundbiz 🙌🏻🙌🏻🙌🏻
@AdamKLMChannelАй бұрын
fuhh padu bro.... 👍🏻👍🏻
@jblsoundbizАй бұрын
Tq so much bro 👍😉
@jblsoundbizАй бұрын
Hi, today's video is about setting up a PA system using True Wireless Stereo (TWS) with the subwoofer in cardioid mode. I used four JBL EON speakers, the JBL EON715 and JBL EON718S models. I hope you enjoyed this video. If you have any questions, please feel free to ask. I'm happy to answer them. If you don't mind, please give my video a thumbs up and subscribe to my channel. Have a great day! 🤗
@kifley19Ай бұрын
Can I play music through both speakers via bluetooth without using a mixer?
@jblsoundbizАй бұрын
Hi, Thank you for your comment. Yes, you can. ☺
@kifley19Ай бұрын
Can you connect both 715 speakers via bluetooth to play the same song?
@jblsoundbizАй бұрын
Hi, thanks for your comment, Yes, you can. You can watch my video here kzfaq.info/get/bejne/jNFjnMh92afUgH0.html Please support my KZfaq channel by subscribing and clicking the LIKE button on this video. Thank you and have a great day! 🤗
@ELECTRICSCARSАй бұрын
With the JBL Bluetooth Speakers, the bass is reduced when you turn the volume up. Is that the case with the EON too?
@jblsoundbizАй бұрын
Hi, thanks for your comment, The bass sound gets louder as the volume increases on the JBL EON718S. Please support my KZfaq channel by subscribing and clicking the LIKE button on this video. Thank you and have a great day! 🤗
@MrThewintechАй бұрын
i have the same speakers but i was wiring them differently, how you did it it actually sounds alot better and the clipping is actually gone. thank you!
@jblsoundbizАй бұрын
Hi, Thank you for your comment. I'm glad that this video could give you some inspiration. I hope you can support my KZfaq channel by subscribing and clicking the LIKE button on this video. I really appreciate your support. Thank you and have a great day! 🤗
@masterbob9112 ай бұрын
Hello, I need help... I have 2 x EON 715 and 2 x PRX 915 XLF. I am using JBL Connect Pro software version 2.00.00. I created 2 groups, one for the SUBs and another for the TOPs. I can't rename the groups even when pressing the pencil to edit them... Am I the only one seeing this problem? THANKS
@jblsoundbizАй бұрын
Hi, Thank you for your comments. Your problem is the same as mine using JBL Connect Pro App v2.00.00. I also can't rename groups, even in demo mode. I have emailed JBL and am awaiting their response on this issue. I am also waiting for the next software update for this JBL Connect Pro App and hope it will fix the problem. 🤗
@oleagonzalezjhonathangabri50552 ай бұрын
Es normal que el limitador del bajo encienda aun ya teniendo actualizado ? Lo manejo como a 3 db y apenas sinto que esta dando el bajeo bien pero enciende el limte Espero su respuesta gracias
@jblsoundbizАй бұрын
Hola, Gracias por tu comentario. En primer lugar, instale la última versión de la aplicación JBL Pro Connect App v.02.00.00. En segundo lugar, actualice el firmware v5.1.3.0 del subwoofer JBL EON718S. Luego reproduce tu música y comprueba si la luz del limitador sigue encendida o no. Tuve este problema antes, pero después de actualizar el firmware y la aplicación JBL Pro Connect, la luz del limitador ya no está encendida. No olvides apoyar mi canal de KZfaq haciendo clic en los botones SUSCRIBIR y ME GUSTA de este vídeo. Gracias y te lo agradezco. ¡Que tengan un buen día! 🤗
@oleagonzalezjhonathangabri50552 ай бұрын
Es normal que el limitador del bajo encienda aun ya teniendo actualizado ? Lo manejo como a 3 db y apenas sinto que esta dando el bajeo bien pero enciende el limte Espero su respuesta gracias
@jblsoundbizАй бұрын
Hola, Gracias por tu comentario. En primer lugar, instale la última versión de la aplicación JBL Pro Connect App v.02.00.00. En segundo lugar, actualice el firmware v5.1.3.0 del subwoofer JBL EON718S. Luego reproduce tu música y comprueba si la luz del limitador sigue encendida o no. Tuve este problema antes, pero después de actualizar el firmware y la aplicación JBL Pro Connect, la luz del limitador ya no está encendida. No olvides apoyar mi canal de KZfaq haciendo clic en los botones SUSCRIBIR y ME GUSTA de este vídeo. Gracias y te lo agradezco. ¡Que tengan un buen día! 🤗
@metanoiax21302 ай бұрын
have you tried maxing it out? did it reach atleast 110db without limiting?
@jblsoundbizАй бұрын
Hi, Thanks for your comment, I have never measured sound volume up to 110db with an SPL meter. However, I am sure that the limit light will not come out even if the sound has reached 110db. Maybe in the next video, I will measure up to 110db for a PA system setup like this. Don't forget to support my KZfaq channel by clicking the SUBSCRIBE and LIKE buttons on this video. Thank you and I appreciate it. Have a nice day! 🤗
@metanoiax2130Ай бұрын
@@jblsoundbiz thanks for the reply! Definitely gonna check your video out, subscribed!
@CristophCCS2 ай бұрын
I just bought the same set up of this video, and so far I've used it with a mixer and it sound very good tbh. However I'm curious about using the TWS, I did set it up on my mobile app, but how do I use a music source from my iPhone to play on the speakers? I tried Spotify and when selecting the speakers I don't see my JBL nor anything related to them...
@jblsoundbiz2 ай бұрын
Hello, Thanks for your comment. Good question. I have never thought about playing songs from Spotify on my iPhone and connecting via Bluetooth to the JBL EON715. I will try it first and let you know how it goes. Thanks and have a great day! 🤗
@kifley19Ай бұрын
@@jblsoundbizdoes it work?
@jblsoundbizАй бұрын
Hi, thanks for your comment. I have tested with my Bluetooth iPhone playing songs from Spotify. Both JBL EON715 speakers can play songs with a TWS connection. I will make this video tutorial in the future. So please subscribe to my KZfaq channel so you don't miss my next video, thanks, and have a great day! 🤗
@jblsoundbizАй бұрын
Hi there, I have tested with my Bluetooth iPhone playing songs from Spotify. Both JBL EON715 speakers can play songs with a TWS connection. I will make this video tutorial in the future. So please subscribe to my KZfaq channel so you don't miss my next video. Thanks and have a nice day! 🤗
@tijae223 ай бұрын
In this setup using the exact same mixer is it better if a laptop is your source going from 3.5 mm to a single or dual Y 1/4?
@jblsoundbiz3 ай бұрын
Hi, thank you for your comment, Good question. Both can be used but many people use the dual Y 1/4 and I am not sure why. Maybe one of the sound engineer who read this comment can explain this. ☺
@aronkovacs18163 ай бұрын
Hello, I would like to buy this subwoofer, but I hear from many places that the limit LED often switches on. I've never tried this sub before, so could you give me some tips and tricks about it? The sub would not be connected to its own eon speakers, but the signal would go from a mixing amplifier to the sub with my own passive speakers. But knowing this, what could I do in Jbl's application?😁
@jblsoundbiz3 ай бұрын
Hello, Thanks for your comment. Here is a response to your comment. Limit LED Lights ```````````````````````` This JBL EON718S subwoofer needs to be updated to the latest firmware to fix the LED limit issue. Mixer Amplifier + Passive Speakers + JBL EON718S ````````````````````````````````````````````````````````````````````````` Connect the mixer signal output (XLR cable) to the JBL EON718S subwoofer CH1/CH2 inputs. Open the JBL Pro Connect application and adjust the EQ to your preference. You can also try the preset EQs provided or create your own custom EQ. I hope I was able to answer your questions and if you don't mind, please give my videos a thumbs up and subscribe to my channel. Take care. Have a great day 😉.
@aronkovacs18163 ай бұрын
@@jblsoundbiz Does the sub really have big bass? Because I have 2 Jbl JRX 225 speakers and I don't know if it would really make such a big difference in terms of bass. What do you think?
@Dj_Cerrillo4 ай бұрын
Suenan mejor que una JBL 712 EON? Las irx112
@jblsoundbiz4 ай бұрын
Hola, Gracias por tu comentario. Ambos parlantes tienen muy buen sonido. Pero yo elegiría el EON712 porque tiene la flexibilidad de ajustar el ecualizador. El IRX112BT sólo tiene unos pocos ajustes preestablecidos de ecualizador y no se puede cambiar. Espero haber podido responder tu pregunta y, si no te importa, deja un me gusta en mi video y suscríbete a mi canal. ¡Cuídate y que tengas un buen día! 🤗
@miguelcoka4 ай бұрын
Thanks, I have 2 EON 700. How do I connect them both in stereo without using a seperate mixer? Do I run an xlr cable from one EON Pass Thru to the other one by connecting the same xlr from passthru to channel 2 Input on the other Eon? Thank you
@jblsoundbiz4 ай бұрын
Hi, thanks for your comments. Yes, that's right, you can also connect the XLR cable L and R from the mixer output to the Speaker No.1 input (CH1 and CH2) and the PassThru to the Speaker No.2 input (CH1 or CH2). I hope I was able to answer your question and if you don't mind, please leave a thumbs up on my video and subscribe to my channel. Take care and have a nice day! 😉
@miguelcoka4 ай бұрын
Thanks so much! I will test this weekend. Setting these up for an event on south beach. Just using the two speakers & one microphone. No instruments being used. ✌🏻
@jblsoundbiz3 ай бұрын
@@miguelcoka You're welcome! Have a great weekend!
@user-sw2ll4mj9w5 ай бұрын
Does the sub actually require inputs from each speaker or can it use just 1 from “through” port?
@jblsoundbiz4 ай бұрын
Yes, that's right. You need to connect both channels to the subwoofer via pass-thru if you want to play the sound in left and right stereo. You can also use one of the pass-thrus from either speaker connected to the sub. If you don't mind, please subscribe to my channel and click the like button on this video. Take care and have a nice day! 🤗
@jackcreek56415 ай бұрын
Do you have to have a connection to both channels on the sub when using pass through?
@jblsoundbiz4 ай бұрын
Hi, thanks for your comment. Yes, it's true. You need to connect both channels to the subwoofer via pass-thru if you want to play the sound in stereo left & right. If you don't mind, please subscribe to my channel and click the like button on this video. Take care and have a great day! 🤗
@DjBside8155 ай бұрын
Can i use a direct input into channel 1 of the host monitor so i can have a wired connection from my dj controller?
@jblsoundbiz5 ай бұрын
Hi, thank you for your comment, Yes, you can. You can connect the XLR cable from the DJ controller to the CH1 input of the HOST speaker, and you can connect to the REMOTE speaker via TWS. Don't forget to click the LIKE button on this video and subscribe to my channel. I appreciate it. Thank you and have a great day today! 🤗
@Lucius200915 ай бұрын
Im sorry but your sound test is awful, the selection of music and the lack of speaking and explaining what are you doing. Also your recording device and method is totally amateur
@jblsoundbiz5 ай бұрын
Hi, thank you for your honest comment. I appreciate it. When this video was produced, I admitted many mistakes as you said. However, I try to improve from time to time to produce better videos. Again, thank you very much for your comments. Maybe you can watch my latest video here kzfaq.info/get/bejne/jNFjnMh92afUgH0.html and wait for your next honest comment. Take care and have a great day! 🤗
@Litcentral095 ай бұрын
I got a question. When I’m playing music sometimes and I turn the volume up I start hearing a little bit of popping in my speakers do you know what that can possibly mean? It really only happens when certain songs got some good bass to it. It don’t matter how low the volume or how high. The limit light don’t even come on
@jblsoundbiz5 ай бұрын
Hi, Thank you for your comment. This has happened to my JBL EON715 speakers. When the music starts playing, a POP sound is heard and then disappears as the music plays. However, not all the songs I play have a POP sound. I am not sure what is causing the POP sound. The only thing I could do at that point was make sure all the XLR connections from the mixer to the speakers were securely connected with no loose wires. I also updated the firmware to the latest version. So far I haven't heard the POP sound. I hope this answer helps you a bit. Have a good day my friend! 🤗
@Litcentral095 ай бұрын
@@jblsoundbiz thanks bro I’ll try that. Do you think turning the DB gain up in the settings will help?
@jblsoundbiz5 ай бұрын
@@Litcentral09 I don't think so. Maybe you could try setting the EQ to flat first and then slowly turn up the volume fader and see if the pop sound still comes out. 😊
@Litcentral095 ай бұрын
Yea I tried putting it on flat and it’s still doing that. I’m thinking maybe it’s time for a new speaker.
@jblsoundbiz4 ай бұрын
Hello friend, Can you play a song that has a "pop sound" using Bluetooth from your PC? and set the EQ to flat on that speaker. I wonder if the problem is still the same.
@williamcallender97045 ай бұрын
Hi there. Very informative video. Which brand tablet are you using to run the pro connect app? Reason i asked is that i can use the app on my samsung phone but not with my amazon firehd 10 tablet.
@jblsoundbiz5 ай бұрын
Hi, thank you. Thanks for your comment. I use Lenovo Tab P11 Plus with Android OS. You can use your SAMSUNG phone as long as it uses Android OS. Have a great day, friend! 🤗
@_Cadenas_Of5 ай бұрын
Name song
@hainguyen86105 ай бұрын
How do I connect additional monitor speakers and microphones?
@daxtonriggle31296 ай бұрын
I have the 2 eon 715 I’m just running the mixer in the speaker itself. How can I hook the 718 subwoofer up without running wires or is that not possible my 715’s are connected through the app and play like a champ but I have no sound coming from the 718
@Litcentral096 ай бұрын
Hey thanks for the video. So I got a question bc I’m a DJ and was wondering if I can DJ wireless but the problem I have is when I play music it’s a reaction delay when I play music or do any type of scratching. If I press play on my laptop it won’t play on the speaker for like maybe half a second. Is it anyway to fix that?
@jblsoundbiz6 ай бұрын
Hi, thanks for your comment. Can you check the Bluetooth version on your laptop? If your laptop's Bluetooth version is below v5.0, e.g. v4.2, then your laptop may be experiencing lag issues. The EON715 has Bluetooth v5.0. Your laptop's Bluetooth version should be at least v5.0 or higher. Also, make sure your speaker firmware is updated to the latest version. I hope I was able to answer your question. Have a nice day, my friend! 🤗
@Litcentral096 ай бұрын
@@jblsoundbiz Ty
@HAIYANE99106 ай бұрын
Hey can use cardioid mode but only single Subwoofer?
@jblsoundbiz6 ай бұрын
Hi, thanks for your comment. As far as I know, the cardioid subwoofer mode can only be used when two subwoofers are used side by side. It is not effective when using only one subwoofer. I hope I could answer your question. Have a good day, my friend! 🤗
@HAIYANE99106 ай бұрын
@@jblsoundbiz nice talk with you too. I'll stick with Eon 710's with 718's soon😊
@jblsoundbiz6 ай бұрын
@@HAIYANE9910 Thank you, friend, If you have more budget, I recommend you buy the EON712 instead of the EON710 if you want to combine it with the EON718S. 🤗
@HAIYANE99106 ай бұрын
@@jblsoundbiz thanks, cuz i want some stereo system that has easy to setup. Not too heavy, and sounds more on clarity:)
@HAIYANE99106 ай бұрын
And I want to know if cardioid works with 2 subs opposed, but using pole mount for tops:)
@jblsoundbiz6 ай бұрын
Hi, today's video is about how to set up a PA System with 2 x JBL EON715 and 1 x JBL EON718S subwoofer using True Wireless Stereo (TWS). I hope you enjoy watching this video. If you have any questions please feel free to ask. I am happy to answer it. If you don't mind, please give my video a thumbs up and subscribe to my channel. Have a nice day everyone! ☺
@secondAngle6 ай бұрын
I'm curious how it is that you go that way from the mixer? Wouldn't it be better if you go from the mixer (L/R) directly into the sub and then distribute from the sub out to the speakers? I mean, why pull two extra wires up/down from floor level when the sub is already on the floor, or doesn't it give the same effect?!?
@jblsoundbiz6 ай бұрын
Hi, thanks for your comment, friend. What I did in this video is actually what is recommended by JBL in the EON 700 Series manual. You can connect from the mixer to the subwoofer and out to the top speakers if you want. ☺
@secondAngle6 ай бұрын
I'm curious how it is that you go that way from the mixer? Wouldn't it be better if you go from the mixer (L/R) directly into the sub and then distribute from the sub out to the speakers?
@jblsoundbiz6 ай бұрын
Hi, thanks for your comment, friend. What I did in this video is actually what is recommended by JBL in the EON 700 Series manual. You can connect from the mixer to the subwoofer and out to the top speakers if you want. ☺
@AlsaAlsa-ns9wg6 ай бұрын
👍👍👍🙏
@yeiselcastillonobrega2666 ай бұрын
Tengo exactamente este mismo audio pero no logro ponerlo como mismo usted lo hace en el video porque no entiendo el inglés si lo tienes en español te lo agradecería mucho gracias saludos
@jblsoundbiz6 ай бұрын
Hola, gracias por su comentario. Lo siento. Haré el próximo vídeo con voz en inglés. Puedes hacer clic en los subtítulos del vídeo y traducirlos al español. Tal vez puedes probar este video kzfaq.info/get/bejne/jNFjnMh92afUgH0.html ¡Que tengas un buen día amigo! 😊
@Litcentral096 ай бұрын
How did you group them ?
@jblsoundbiz6 ай бұрын
Hello, my friend. Good question! It's hard to explain here. I will make a tutorial video about your question in the next video. So stay tuned my friend ! 🤗
@rafaelunplugged6 ай бұрын
There's an icon on the top right corner it's the "chain" On ipad Setup / House icon on the right side Then top rightnis a lock, location, chain icon. Hit chain
@Litcentral096 ай бұрын
If I got a prx918xfl what should I set the parametric EQ to ? Custom, flat, 80hz, 100hz, 120hz or cardioid ?
@jblsoundbiz6 ай бұрын
Hi, thanks for your comment. It depends on what you want to pair with the top speakers (HPF-SPKR and LPF-Mix Out). For example, if you set the top speaker with HPF to 80hz and LPF to 120hz, then the subwoofer's Parametric EQ can be set between 120hz to 80hz. If you want to use Cardioid EQ, you must have two subwoofers and place them next to each other. Subwoofer 1 (facing the audience) is set to 100hz and subwoofer 2 (rear facing) is set to Cardioid EQ. You can watch this video on how to set up a Cardioid mode subwoofer. kzfaq.info/get/bejne/nphmfMl3y7u1fY0.html I hope I can answer your question. Thank you very much for your support of this channel (SUBSCRIBE and LIKE). I appreciate it. Have a great day my friend! 🤗
@Litcentral096 ай бұрын
Thank you for answering. Here is an example of my set up on the left side I have a Prx15 speaker with a PRX18XFL sub . On the right side I have a eon718s and a Eon715 speaker. Now the eon speakers I followed your tutorial from the video to set those up.
@Litcentral096 ай бұрын
Oh yea I also figured out how to group the speakers thank you 👌🏾
@Litcentral096 ай бұрын
Also in the future can you do some videos on the 900series ?
@jblsoundbiz6 ай бұрын
@@Litcentral09 Nice! Well done my friend! 👏👍
@Litcentral097 ай бұрын
Thank you for the video bro. I have a RaneOne and I use to hook up my sub and my 2 tops all into that raneone but you showed me a better way of doing it. I have a Yamaha mixer as well so now I know to hook up my tops to my subs and my subs to the woofer . Thank you brotha 🙏🏾🙏🏾
@jblsoundbiz7 ай бұрын
Hi, thanks for your comment bro. I'm glad my video can help you. If you don't mind, please give my video a thumbs up and subscribe to my channel. Take care and have a great day! 🤗
@djenk123457 ай бұрын
When i use cables the volume is much less loud then when streaming music through bluetooth do you also have that problem ?
@jblsoundbiz7 ай бұрын
Hi, thanks for your comment. Yes, that's right, I also feel that the sound is a bit louder when using Bluetooth than when using an XLR cable. I don't think it's a problem. In my opinion, it may be because XLR cable has impedance compared to Bluetooth. If you don't mind, please give my video a thumbs up and subscribe to my channel. Take care and have a great day! 🤗
@koilpul-lq7bm7 ай бұрын
Bro I have need the Sound systems jbl 1.Eon 715. 4 2.yamaha 16 channel mixer 3.podiom micks. 2 4.codeless micks. 2 5.instrument cables. 6 6.xlr cables. 12 7.Aux cables. 2 8.coddid micks. 8 9.mick stand big. 4 10.mike stand small 5 11.slabitizer. 3kvw Auto
@jblsoundbiz7 ай бұрын
Hi, thanks for your comment. I'm not sure what you mean. Can you explain what you mean by that list of audio equipment? Forgive me if I am wrong. 😊
@dersanvs7 ай бұрын
Super information
@jblsoundbiz7 ай бұрын
Thank you ❤
@yasmimvitorya15018 ай бұрын
porque você deixou os subs em diferentes equalizações?
@yasmimvitorya15018 ай бұрын
eu consigo configurar a caixa sub e a caixa de voz pelo aplicativo ao mesmo tempo?
@jblsoundbiz8 ай бұрын
Hola! Gracias por tu comentario, Sí por supuesto que puedes. 😊 Al utilizar la aplicación JBL PRO Connect, puede configurar ambos altavoces al mismo tiempo.
@dannomorgan30028 ай бұрын
Hola! Muchas gracias por tu video. Yo también tengo un JBl 718 y dos JBL 715 como sistema de audio. Soy músico y toco en eventos en vivo. La cuestión es que estoy notando que algunas personas conectan las bocinas de 15 a la mezcladora y de las bocinas de 15 conectan al Sub 718. Yo, por recomendación de las personas que me vendieron el equipo, conecto la consola al canal 1 y 2 del Sub de 18 y de las salidas Thru del Sub de 18 conecto al canal 1 de cada una de las bocinas de 15. Qué diferencia hay entre las dos conexiones? Que es más recomendable? Conectar el Sub a la mezcladora o conectar las bocinas de 15 a la Mezcladora y de ahí pasar la señal al Sub? De antemano muchísimas gracias.
@user-hp8vj3hc8g8 ай бұрын
Hi First of all, thank you for this video and detailed explanation bringed with a smooth music. I am planning to buy this setup. I already ordered the 2 speakers EON715.... and I will for sure order the EON718S. I would like to know your point of view concerning this configuration of connection : 1- Connect the mixer (Yamaha MG) R and L "out" to the EON718S on CH1 and CH2 2- then 2.1- connect EON718S passThru 1 to Speaker EON715 CH1 2.2- connect EON718S passThru 2 to Speaker EON715 CH2 In this configuration we can spread the speakers from subwoofer with less length of cable if we keep the EON718S near the Mixer (Yamaha MG). and we give possibility to add other satellites (speakers EON715) interconnected to the others with passThru Thank you for your feedback
@jblsoundbiz8 ай бұрын
Hi, thanks for your comment. You can use that connection configuration. I agree this would save using a long XLR cable. But please remember that you must set the signal delay between EON718S and EON715 to about 1.1 feet per ms. Anyway, thanks for your thoughts on configuring this connection. I appreciate it. I will make a video of this type of configuration and see how it sounds. If you don't mind, please give my video a thumbs up and subscribe to my channel. Take care and have a great day! 🤗
@markusg.82594 ай бұрын
You shouldn't do that for proper results. It's also not recommended. I understand your point and did this many years with active speakers that have a passive frequency filter. Out the mixer, sub one, sub two, top. But that isn't the way it works with this. Because the Top has all the possible Mix Out options, the sub hasn't, so always from mixer to the top and then add the subs.
@arnellorena85638 ай бұрын
I can't connect my 2nd speaker to Bluetooth
@jblsoundbiz8 ай бұрын
Hi, thanks for your comment. May I know which Bluetooth you want to connect? BT Audio Pairing or BT Control Pairing on your second speaker? If you don't mind, please give my video a thumbs up and subscribe to my channel. Take care and have a great day! 🤗