Hi quick questions how did u rewire new sub if they where connections or did you use aftermarket amp. Or do u have a step by step video of how to do everything thing and nice car as well i have the e500 love mercs
@redbaron2448Күн бұрын
@@lukejoseph2383 I had a separate amp to wire the subs
@lukejoseph2383Күн бұрын
@@redbaron2448 ohk I wouldnt know how to do that as I've got to batterys one in boot for air ride and a small as one under the hood of the car was gna try be cheeky and just put sub in place of old one and try connecting it up that way but if need a aftermarket amp then I'll have to figure out how to wire that in and what battery I go from
@burhannomani244416 күн бұрын
Excellnet and may be ONLY Informative video on this Issue. PLEASE ANSWER IF THE CAPACITOR attached to this plate showing no continuty would it have the same problem. My plate attached capacitor shows no continuity and I have ordered the same part coming from France. In last 4 years I must have watched over 100 Videos may be some more than 2 times, changed a front and back battery but constatntly have this Battery DRAIN Issue and one was fixed with following the Video under passanger adjustment seat. Signs of Visit Shop for Battery, Break and all the similar keep on comming. I am hoping that this replacement of attached Big Capacitor would resolve the Issue. I did not take out the fuses and checked them individually as they were attached to the same plate and now Wounder it shws fine but may be if one is bad, other is good but atatche to same may show both fuses are good. if anyone can HELP on this batetry issue, please emmehoustonbn12atgmail. I thank you in advance.6/12/2024
@patientprogrammer0017 күн бұрын
I might need to do the same thing on my 2006 w271. I bet it's located in the same spot. Damn bastards... I wish them the flies of 1000 camels and hands too short to scratch themselves.
@danielsantana5115Ай бұрын
Hola saludos, buen video🎉 tengo un mercedes w211 tiene ese mismo modulo compre la batería auxiliar nueva y la medi con el multímetro con el carro encendido marca 12.60 voltios deberia de marcar 14.20 correcto puede usted confirmar con su vehículo para yo descartar y comprar ese rele gracias!
@user-fd5rv9ft8rАй бұрын
Why don't you find a new way to lift the fuel rail so you don't keep busting you knuckles?? You can use a piece of wood to lever it up
@ChrisLopez-oh7oxАй бұрын
Yo bro do you have a link to that Bosch pump that you say works on instant?
@redbaron2448Ай бұрын
No link, it's called Bosch 010, eBay Amazon, VRP
@RoadTripA1AАй бұрын
It's junk when you can't apply it correctly.
@cliffgarcia1393Ай бұрын
Gotta a Gen 1 2005 trying to do the oil change bike was givin to me the problem I'm having is an don't know if anyone else is but the oil filter hits turbo do I have to remove turbo to take off filter because it's hitting any thoughts thanks
@redbaron2448Ай бұрын
Best thing to do is take it to whoever put that turbo on and ask him since these bikes do not come with turbo stock, something they probably didn't think of, oops
@prismamartinez1434Ай бұрын
Ok I appreciate the response thanks
@SenajidSomicАй бұрын
Please color code?
@pernellwatlington7952Ай бұрын
Pretty deep red
@neilgunns8391Ай бұрын
Just like that you scratched the fairing on the ground. 😱 I knew it was coming.
@redbaron2448Ай бұрын
It didn't scratch
@jonathanleon62112 ай бұрын
Yo this giy is awesome thanks they were gonna charge me 675 dollars for things thats are super simple
@ragingpatriot7722 ай бұрын
A turkey baster works good for mixing small batches
@ABE5US2 ай бұрын
This video was made years ago 😅!! I wonder if you made a 2nd video of install and how it sounded !!
@redbaron24482 ай бұрын
Yeah video of install is there and sound clip 2nd video
@RobertMihai052 ай бұрын
Hello, i have Many communication problem with my s211..so I Did open the junk box and I found that my 200 fuse it’s blown..physicaly break, for what is the 200 fuse? Red cable with 200 amp..Sorry my bad english..and thank you for eventual answer..
@redbaron24482 ай бұрын
If your 200 amp fuse is broken replace it
@RobertMihai052 ай бұрын
I’m Gonna order it tommorow..i have a no crank no start problem..so i’m wonderning if it’s because of it..i have checked ecu..front sam..all fuses..all seem to be allright..no corrosion signs..maybe it is because of Thais blown fuse
@RobertMihai052 ай бұрын
I don’t know..because when I bypass the engine relay it start normal..when i don’t bypass i have esp check..abs..and no crank no start
@BusaDad3 ай бұрын
I've been having a problem with mine completely losing power at 8 and 9 thousand rpms and not for sure what the problem is but i noticed a lot of others having the same problem and one guy ended up replacing the whole wiring harness before the problem was resolved but the other people had different issues but causing the same problem so im lost🤔🤔
@redbaron24483 ай бұрын
Not sure never had this problem, but losing power could be wires but spark plugs could be fouling out or plug wires but I'm kinda just guessing, I've been lucky I guess not 1 problem with my 04 in 20yrs
@85jordanboi2329 күн бұрын
Check your throttle position sensor. There’s a good vid on KZfaq showing how to check it and set it. It had my bike going crazy until I adjusted it
@BusaDad29 күн бұрын
@redbaron2448 thanks I appreciate the tip going to go check that now
@BusaDad29 күн бұрын
@85jordanboi23 Thanks for the information im fixing to check that and my wiring harness,spark plugs,plug wires.
@BusaDad3 ай бұрын
I subbed up💯 we need more how to video's on these older generations' bikes, so i look forward to watching more of your content.
@redbaron24483 ай бұрын
Great thanks for the Sub, did a couple more on the cowl putting the bar in and bike is running great no problems so if something comes up I will post videos Gen 1😍
@BusaDad3 ай бұрын
Hell yeah, and i appreciate it too because I have a 2003 busa that's due for an oil change. When i looked up an oil change on Gen 1 busa, your video was the first on the list👍👍
@redbaron24483 ай бұрын
Glad I can help. Stay safe out there 🙏
@floridaman51253 ай бұрын
Mine was corroded and causes me grief for a month before I found it thanks to KZfaq! Changed it myself, probalems went away a day later after some serious time behind the wheel.
@mrmuhtish3 ай бұрын
Installing the long tubes right now. Major pain getting the bottom nuts off of tue headers, along with disconnectimg the y-pipe from the resonator.
@joshuaJosephjr3 ай бұрын
8:25 😂😂😂😂😂😂😂
@Hargy903 ай бұрын
No orange peel? All I see at 8:00 is orange peel
@gledisxt3 ай бұрын
What did u loose up to remoce coil pack on cylinder 1-2
@redbaron24483 ай бұрын
Don't remember, t Sockets, everything should be in video 1
@kidmagik3 ай бұрын
Ok so my lights work on my right side and only my high beam and fog light works on driver side could that be a blown fuse in the Sam box as well because every other fuse is perfect
@redbaron24483 ай бұрын
No, box is for voltage, regulators, Start ups, dead battery, your is something, else bad ground or crossed wires
@ashamarks-eo8jb3 ай бұрын
At what mileage did this M177 have on it when you did the spark plugs? I have about 40k miles and thinking about doing this. Also those spark plugs that you took out were in really bad shape.
@redbaron24484 ай бұрын
Melts plastic as it cuts, not a clean cut
@MarcusB694 ай бұрын
What's wrong with using the Dremel??
@JohnSmith-xc7xk4 ай бұрын
was this keeping your Benz from starting?
@redbaron24484 ай бұрын
Yes and No, wasn't starting because battery kept going dead, this box if battery is Dying after replacing alternator and other parts
@pgchem4 ай бұрын
What is best oil for hayabusa gen 1? 10W40 or 10W50 or 5W40 ? Full syntetich? Semi or mineral? for example: Motul5100 or 7100 or 300? or Bel-Ray EXS Full Synthetic Ester, or Motorbike 4T SAE 10W-40 Street
@redbaron24484 ай бұрын
10w40 full synthetic any good brand will do
@KILLER.964 ай бұрын
Hi and thank you for the video, how many litres in total have this transmission, my transmission have a big leak becouse of the pipe that go in the cooler sistem and now is been fixed bod I don't know how many litre I total have so I can fill it up, I really appreciate sir
@redbaron24484 ай бұрын
Took 4qts
@KILLER.964 ай бұрын
Full transmission? My one is w204 350 v6 petrol automatic 2008
@redbaron24484 ай бұрын
@KILLER.96 yes, what ever you drain put Just measures it and put back the same amount that came out
@KILLER.964 ай бұрын
The problem is that I don't know how many litre I lose, what should I do, drain all and fill the exact amount required for the transmission
@redbaron24484 ай бұрын
@KILLER.96 if you drain and fill its only 4qts
@silvercommander4 ай бұрын
Love mine
@mrmuhtish4 ай бұрын
Just what I needed. If the studs are rusted, which they are I'm sure, why not replace them? Or did you end up replacing them.
@redbaron24484 ай бұрын
Mine weren't rusted so I didn't have to replace them. You just have to replace the nut as it is one time use only
@user-ip3uv9ht3m4 ай бұрын
I searched and searched and your video is exactly the answer I was hoping for! Long story short I had our wood burning stove removed and now I've gotta put down flooring....well needless to say our original wood floors look just like these so I wanted to make a easy matching/new floor look! Wish me luck! 😅
@redbaron24484 ай бұрын
Good luck, thanks for watching
@pawekocjan26934 ай бұрын
Hi. Do i have to move everything like You to change airmatic fuse? Or is it possible to make it the other way?
@redbaron24484 ай бұрын
This has nothing to do with Airmatic fuse
@Granola8Lavender5 ай бұрын
Did you need an amp for that speaker ?
@redbaron24485 ай бұрын
No, used factory amp
@theroughblueram114thgen55 ай бұрын
I’m gonna use HQ’s PDN destroyer gray with the wet euro clear coat
@kadenlindsey3585 ай бұрын
Thanks for the vid, helps me get a good idea for my project. This is not "full-coverage" as in flake covers the panel completely with no base showing through but still, if it can spray what you did i'm sure it can do more!
@srdjan58475 ай бұрын
Measurement for enough oil in diff is bottom edge of filling hole. When oil starts to drip that is enough oil in diff. Also, car has be horizontal for right measurement. Plugs have to be tightened according to manufacturers specks.
@Rodgarc325 ай бұрын
Why do you have dark spots on fender and doors on driver side
@floridaman51255 ай бұрын
Every time I turn around there’s another relay or fuse someplace. Thanks for the video.
@AngelBaseball276 ай бұрын
Did u have a little relay clicked on auxiliary battery im trying to figure out what that does 04 e55 amg
@redbaron24486 ай бұрын
No, what it does it gives power to the batteries
@AngelBaseball276 ай бұрын
@@redbaron2448 okay thank you 🙏
@floridaman51256 ай бұрын
HUGE thank you for this video, I swapped mine out today . Maybe it will fix my issue, it certainly can’t hurt.
@redbaron24486 ай бұрын
Good luck as it could be other issues when it comes to batteries 🔋. But this is the most common problem
@floridaman51256 ай бұрын
@@redbaron2448 two new batteries, new alternator and voltage regulator, rear control module was very ck Lean (no water intrusion), front relay was corroded on the left cable. The battery protection came on a few more times, but stayed off the last drive. That gives me hope. No matter , I feel smarter and know more about my car now.
@floridaman51256 ай бұрын
Good to know the nuts are attached to the wires, I was afraid of dropping them.
@Cobra427Veight6 ай бұрын
I have some decals to add , I think I need to do at least 2 clearcoats over my candy and then sand the peel or imperfections out , I'm just not sure what fine grit to use , then once the decals are on, then a mist coat of clear , and then another clearcoat . Does this sound right ? .cheers for video .👍
@redbaron24486 ай бұрын
You need a minimum of 3 to 4 coats of clearcoat for Kandy before you start sanding, 600 grit then put stickers if your going to flow coat with 3 more clearcoats. If buffing then put stickers on 30mins after basecoat Kandy dries then 3 coats clearcoat then wet sand with 1500 grit, 2000, 3000 then buff
@bee23336 ай бұрын
How long did you wait for sealer to dry before basecoat
@redbaron24486 ай бұрын
I always wait at least 24hr before putting on basecoat, but you can use basecoat after 1hr of sealer
@1962moon17 ай бұрын
Notice he didn't show how he got the other bolt out
@redbaron24487 ай бұрын
Easy peasy, figure it out, lmfao
@santinoeli715067 ай бұрын
That has got to be an RCSB
@carolthompson90607 ай бұрын
🤦 if you had your gun settings nice, you wouldnt have peel , or peel to that extent .
@rodneyturner68927 ай бұрын
Nice clear
@robertehlers43308 ай бұрын
You want it to sound real good remove whole system because fiber sucks and all thise speaiers are weird ohms 2 4 8 ohm speakerslol. The JL c1 fit in stock location perfect. Also i have not seen nobody do this yet you dont have to remove the whole door panel thise harmen kardon 6.5 stock speaoers that piece pops out saves time easy. Even jl c1 tweeters fit. The headunit take it out its dated and then f you want better sound loose amp and headunit. You will need new amps for it to work though.