hi whats the benefit of running 4 pipes of the boiler and not 2 like most do, ?

U need to tamp the coffee for the express n crema to comr through

He didn't tamp

The spider support started to fall on my Miele W5478 but was 10 years old Miele wrote it off and wouldn’t fix it even though it was totally fixable…

Great video. You said it was thenchain tensioner, but what was wrong with it, did you not get a new replacement in the kit?

My did the same. Just drop few .

what happend finally what was the problem??

Check your long and short term fuel trims using obd diagnostic tool that looks like a rich condition to me. Does it smell eggy? U might have a bad upstream o2 sensor

Try using one of those maguiars car bombs to get rid of the ciggy smell. I had a mate buy a car from a dog owner and he said that cleared the smell up for him. I think it only takes about 10 minutes from start to finish too

Good luck with that mate! I like the video format where you have a video of every stage of the process. Great stuff and I've just subscribed.

I took my machine to the repair shop for repairs and he said the drum is spoiled and have to replace it another one . I want know if the drum do spoils

I like the video

No ish! Your right but thats obvious.

How much is scrap price for pewter in UK?

That’s what you get for using quick wash. Quick wash should abolished

This is an insult.

Really useful review - thank you. How has the BBQ stood the test of time 8 months later? Would you still recommend it?

Hi! Good video. Is it possible to replace just the heating element and assemble the pump back? You said you had to brake the mounting?

Thanks maybe one day you will ha e one 😂

Cool car

I have

HAS ANYONE HAD THIS ON THEIR POLO?

the ground coffee aint grounded for an espresso.

You did more dismantling than may be needed. In order to remove the front of the machine you do not need to remove the control panel. Take out the screws holding the door lock and the Torx 30 below the door. Remove the seal spring as shown and the two screws at the bottom of the front The front will them drop down and clear the pins holding it at the top.

Did you submerge the drawer in brick acid or spray it on then clean?

Spectacular views and the commentary is second to none!!!

One never gets tired of these gorgeous views.

What if its show that waterfault alert into miele washing machine sir?

Looks hot

I have the same machine- no problems

Just done one, horrible design, who would design a chain tensioner without a ratchet, stupidity at it's finest. Probably ratling as got low oil pressure, did you clean the sump , pickup checked ? Mine worked excellent after the replacement, but it is quite a junky car overall.

What did it end up being? Chain tensioner?

Looks like coffee is too fine grounded

will it tell you where the airbag fault is or does it just turn off the airbag light?

they literarry just slammed whatever letters on the keyboard and called it a day

The thick foil heater rings are a lot cheaper than a new pump.

No clue about manners. What an annoying person. I would have moved.

I Have the same proble with my W1 that is about 7 years old. It looks like Miele are not anymore the Miele.

I live in atown where a tank in the loft melted and the burst was over the woman's bed causing her horrific death No tank or metal is better

2023... and they still build spiders like these...

Per toglierlo prendete una pinza di quelle bloccabili e distruggetelo, altrimenti è un lavoro impossibile e da pazzi, il taglierino lasciatelo perdere, rischiate seriamente di ferirvi

quicker doing it by hand lol

Nice to see a woman doing a man’s job for a change, she’s not got the hands for quick up and down movements.

Yes we bought as my wife struggled with the manual jack the other day. When home I have professional trolley jack. Never used the balloons type must try one day 👍

I seem to recall quite a few years back that an inflatable balloon could be placed under the car, within reason, as it spread the load, it could be positioned anywhere. Scissor jacks were always useful although in my enthusiast days had a nice trolley jack.

Yes

It looks and sounds ship...am I right??

We just replaced the two Friction Dampers, Shaft Seal and the V-Belt. All purchased from Miele for our W1213 washer. We were so happy until we tried to turn it on. The beeper was repeatedly beeping and the display showed - - -. We never touched any part of the digital control panel so we cannot figure this out. We took pictures as we took everything apart. Can you help us figure this out? Thank you very much, Donna Mc

Icky.

Not bent valves ,there is compression on all cylinders