Ty 4 this video, your replies over the years & all comments...
@LawnStripe07153 ай бұрын
I had the exact same thing happen to me! I was looking and looking online and couldn’t find anything until I found this video! You’re a total life saver man! It works great! I did everything step by step and I’m up and mowing again! Thank YOU!
@alancowart44188 ай бұрын
do you have a list of pieces i need for this repair
@tinkerberns52169 ай бұрын
Wouldn't that fuel line hose get hot and worn in time and you have another mess?
@TheCchilly9 ай бұрын
Hasn't in 8 years. Still going...for now.
@andrethegiant30359 ай бұрын
Bro thank you. I was just about to start dropping the deck and getting in there. It was the gas cap.
@brucer122010 ай бұрын
This pulley comes with a separate shoulder: Looks like it would work ---> "STENS 280-164 John Deere AM37249"
@canamrider719510 ай бұрын
Same thing with an LA130 I owned.
@lutherramsey2547 Жыл бұрын
Thanks, just fixed my mower
@kevinwhelan2417 Жыл бұрын
great video...I had similar problem on my JD mower deck. I used what I had at the time I put a 2" 3/8 bolt in the hole from the welded bolt from underneath with washers and found that lock washers fit where the bushing should be and used 3 of them for the spacer, then topped with another washer, lock washer and nut, so far so good!
@d3l1a2704 Жыл бұрын
Purchased this to replace a guide pulley kzfaq.infoUgkxO9seYZjlnuP5UvMkb7osQW3WxPVeSnPk on our John Deere x304 snowblower. As I stated in the title, it is just about perfect. The stock pulley has a spacer at the bottom. I used four washers to emulate said spacer, and it works perfectly now. Great product, and great price especially if compared to typical JD prices.
@randyboyett1366 Жыл бұрын
So did the repair last? I have the same issue.
@JazzyJS58 Жыл бұрын
I had the same problem it was the throttle cable it wouldn't stay at the level I had it works fine now.
@nateparker4177 Жыл бұрын
I took a grinder and took of the bolt. But now the entire surface is flat with nowhere for. Bolt. Do I need to drill a new hole?
@TheCchilly Жыл бұрын
There should be a hole. You may have ground the bottom of the bolt into the bracket. You may be able either pop it out of drill it out. If not, you would need to drill a hole.
@domenicclavillas3972 Жыл бұрын
Nice job sir.
@johnnybaber1804 Жыл бұрын
She stopped the top of my head which isn't very high I've heard that they put a liner inside the fuel line nowadays combats the adverse effects evading ethanol to our fuel. Is there anybody else having a heck of time trying to keep their weed eater running or their gas blower won't even start I'd bring you gas out in mine was black looking and it hit separated into look like water maybe something in with it I know it cleans the heck out of the spark plug it looks like with the fresh fuel but darn you get looks like I get it just the carburetor so now hopefully that'll work I probably use more gas working throttle keeping RPMs up so it wouldn't die! I give a reward if anybody can return my old Sears Craftsman blower to me there was lightweight didn't require a fuel pump or primer bulb etc etc had a compression release inside the engine made it easy to crank first time light years behind what they get nowadays but it was so much better sure I guess you could catch on fire if the float stuck boots 30 years old and I loved it no even if you're the guy who stole it and if you are I need that Hydro power washer back to that was inherited in my gas edger yeah that was special too I think it's just simple stuff that you can find but it was very special to me being partially disabled everything started have a pool of the starter rope now I'm stuck with total junk made out of plastic got to replace the primer bulb every 2 years long the fuel line carburetor parts probably etc etc you have no idea the pain you caused me the money I had to spend to replace it with this garbage and disrespect to the thief yeah that air conditioning unit had a brand new compressor in it that you probably sold for scrap you jerk I will save it for later
@paulreft7133 Жыл бұрын
Can't thank you enough! Saved me $168 for a new bracket! So far its working great, confident it is fixed for good! Many thanks my friend!
@jonschwindt30642 жыл бұрын
The lesson here…….they make a horrible noise in plenty of time to change up before this happens.
@shermananderson7002 жыл бұрын
Clear, concise, good diction, good video. This should help us get ‘ER done.
@RideorDie4012 жыл бұрын
Thank you!!
@rhigg19592 жыл бұрын
How or what did you use to cut the bolt off?
@TheCchilly2 жыл бұрын
I used a dremmel tool but I’m sure a small angle grinder or hacksaw would work as well.
@alanhowell71032 жыл бұрын
Dude, you are honestly a lifesaver!!! My pulley broke right off the bracket. Bought everything you said...works perfectly now! Super cheap repair, thanks to you!!!!
@scottjarson82672 жыл бұрын
Can’t believe this worked. Great stuff. Thank you!
@danielp.75332 жыл бұрын
I’ve been completely racking my brain on my mower. I’ve watched video after video and was ready to spend a bunch of money on parts. Then, I came across your video. I followed your tips and now we’re running great! Thank you so much for sharing!
@thekingtroll22 жыл бұрын
My john deere 115 mower wouldn't start. I had a friend put on a new battery. The gas was flowing in the filter. He put on a new filter. He sprayed ether in and it started but stopped. Today I saw this video and I went down and followed your advice. After a few turns the mower fired right up with full power!! Thank you, thank you thank you. My friend said he'd go order a carburetor and I told him not to do that since gas was flowing. Oh he put on a new spark plus, new air filters, etc. Wow... and I fixed it!
@7percentSolution2 жыл бұрын
Had the same issue where I changed the fuel filter, got in a good mow, then started bogging down again. Am going to try this. Is the gunked-up fuel tank cap related to the replacement of the fuel filter (if it is, can you explain how?), or do you think that was just coincidental?
@caliskier2 жыл бұрын
Dude, dude! DUUUUUUUDE!!! you saved me so much time and money. Totally helped! DUUUUUUUUUUDE!!!! 1 year later and it still works... the other pulley went down so came back here to remember how to fix it. Again, life saver.
@davidbeinke1382 жыл бұрын
So stupid Question. I have a similar issues the the flat idler shaft on the 48". why not just replace it with a Shoulder bolt....
@noahlaribee42162 жыл бұрын
Just had the same issue. Was ready to pull off the carb, spark plug etc. Tried this and it fired right up!! Thanks for the video. Amazing
@stevemeade60722 жыл бұрын
You sir are an inspiration. Great video! I love it when we don't accept that we have to spend large amounts of money for something because we are in a bind. all the while planning in our mind what will work. I think we all should learn how to fix everything that we own to the best of our ability. Keep up the good work......you are awesome! Thank you for sharing your knowledge
@Jwcounseling2 жыл бұрын
Glad I found you. I cannot for the life of me lift that pulley up so I can put the new belt on
@rome36033 жыл бұрын
I appreciate the video, I had the same problem with my mower.
@riversidecountryclub22113 жыл бұрын
My idler looks " cocked up" musta got bent somehow, I suppose the bolt bent. I'm cleaning / fixing up mower now. I'll keep this in mind for sure. Thanks
@Dudejames3 жыл бұрын
I have the same tractor as you
@joller8053 жыл бұрын
Sometimes, simple things are the most difficult to figure out. Thank you very much indeed for this. Cheers.
@cavinallen17683 жыл бұрын
Very true problem, the part number from John Deere is M 71682. Cut the old part off and put the new part on $4.26.
@joshuarivera76223 жыл бұрын
Question to the pulley covers hold the back of the belt from falling off when blade is disengaged? I bought a new belt and testing it keeps coming off. Don't know if I got a bum belt or what.
@kcpaull3 жыл бұрын
Thanks. This happened to our mower the other day and we were stumped as to what to do. My husband just cut the bolt off with a hacksaw. He is having some ice cream as a much deserved reward.
@travdad763 жыл бұрын
Thank you! Will try
@ericstacy86103 жыл бұрын
I hadn’t even thought of this. This was exactly the problem! Thanks so much!
@concepciondeorienteeljorna673 жыл бұрын
Small question if you can help me out i have a jonh deere la 115 i lose the key and ill try to start it with a small screwdriver run but when i try to cut the tractor dont go forward or reverse but when i engage the blades they work but i can't drive the tractor what cam i do please eny one respond Thank you
@qrowok11043 жыл бұрын
Thanks. The weld that held the bolt on broke on mine.
@williama22193 жыл бұрын
After cutting & grinding off the bent bolt, I did this fix using JD parts. As another poster indicated, there's a bushing that fits the JD idler. There's also a 10mm bolt & cap lock that is a perfect fit inside the bushing, and is used in other applications of the pulley. Easy replacement with these parts once you get the offending welded bolt cut off the bracket. Parts list: Idler: GY22082. ($13) Bushing: M71682. ($5) M10 Flangelock: 14M7400. ($2) M10x40: 19M7804. ($3) M10 5x30 washer (2): 24M7178. ($1.50)
@dbateman2 жыл бұрын
This looks perfect, thank you. I was lucky/unlucky enough that the entire bolt broke out where it attaches into the bracket, but that almost makes it easier.
@carlysmith16893 ай бұрын
Thanks for all info, ordered, fingers crossed
@ustmissouri8029Ай бұрын
July 2024. The part numbers are correct. I got them through a john deere dealer in Lee's Summit, Missouri. $15 for everything. Easy fix.
@dddddd21003 жыл бұрын
That same pulley on mine is leaning forward a little so it's not perpendicular. I have a vibration in the deck when I engage the blades, I'm wondering if that leaning Idler Pulley could cause that? I have replaced both Idler Pulleys and belt, still vibrates. seems worse when deck cutting height is set higher.
@gregorydejesus89933 жыл бұрын
Thanks for the video great 👍 resorce
@sankstone3 жыл бұрын
Thank you... Same problem... Had no idea... You saved me... Brilliant
@dddddd21003 жыл бұрын
Thanks for the video, it's appreciated.
@timothywilkerson72484 жыл бұрын
What was the idler pulley part number on Amazon i have a John deere lt180 lawnmower with a 48 inch deck .I'm having trouble finding the same idler but for a lt180 john deere with a 48 inch deck
@TheCchilly4 жыл бұрын
Here is what I ordered. Stens 280-242 Heavy Duty Flat Idler
@kevint29584 жыл бұрын
My bolt is bent I will be giving this a shot thank you for the post😀👍 great fix!!
@tamerasnowden31314 жыл бұрын
How do you remove the original bolt?
@TheCchilly4 жыл бұрын
i used a small angle grinder. A dremmel or something like that would work.
@sfoster999 ай бұрын
I used a multi tool with a carbide blade. Took awhile but it worked.