2 жыл бұрын
3 жыл бұрын
3 жыл бұрын
4 жыл бұрын
4 жыл бұрын
4 жыл бұрын
Пікірлер
@ScottMurray-ow5ot 3 ай бұрын
you bought the wrong kit not saying it wont work but yesterdays tractor has the correct sleeve and seal kit part Item #: 173253 $52 plus shipping no jacking around and works. I own 3 2000 and 2 3000 series have used this on 4 of them. Hope this help every one
@Infiniteatrophy 9 ай бұрын
4 years later, still no part numbers
@mikedarrow3809 Жыл бұрын
I have a Ford 4500 backhoe similar to this. Cool old tractors.
@Louisthebird Жыл бұрын
Part numbers?
@roberttischer3056 Жыл бұрын
Parts # where' ?
@silverdragontaylir8252 2 жыл бұрын
Genius
@stevenjordan6389 2 жыл бұрын
before you pull steering wheel remove the nut then spray brake cleaner on rag wrap around the shaft cover that with a spray can cap add brake cleaner several times.Should be able to woble the wheel by hand.
@willhorting5317 2 жыл бұрын
👍👍 My parents post digger didn't have a hole in the case casting like your's. So my dad welded a short piece of heavy wall 1-1/4" pipe to the side (where you put the horseshoe, above the auger). Then we would stick an old railroad spike bar in the pipe. Dad would remain on the tractor, to operate the up/down action to clean out the loose dirt, while I would pull down on the bar. Always had to be super careful, so I wouldn't get caught by the auger!!! If we hit a rock, or if it hadn't rained for a while and the ground was quite hard, then Dad would get off the tractor and help me. (This was half-century ago.)
@bp-eu6sh 2 жыл бұрын
hmm manuel is his name...
@N3ttwerk 2 жыл бұрын
Nice tractor, I have the same one handed down from my father. Where did you get that red foot step from? I need that.
@bobqwhite1267 2 жыл бұрын
I'm 57 soon to be 58 God's will easy trick put diesel around the rim and tire 😀😀😀😀😀😀👍 😳 OMG one or two walks with the hammer done. Putting the tire back on even easier 🙏
@jesusgonzalez8437 2 жыл бұрын
Does the Ford 3400 has the same system?
@davidlarson4867 2 жыл бұрын
So disappointing when anything goes wrong, so many people just take God’s name in vain
@matg9 Жыл бұрын
Truly sad
@Jcreek201 11 ай бұрын
Goddamnit Bobby
@steveenloe2628 2 жыл бұрын
Exact same tractor thank you much !
@alexcampbell5371 2 жыл бұрын
Very nice
@Buckinghamrabbit 2 жыл бұрын
just checkin but, did you back your truck into it *before* you jacked the tractor up?
@craigkennedy481 3 жыл бұрын
That was the bushing that fits inside if the rubber bushing directly under the steering wheel
@ryderdintwa5458 3 жыл бұрын
How do you bleed 7840 tractor hydraulic steering wheels system
@danieltravis2850 4 жыл бұрын
That was not a Speedi Sleeve, Speedi Sleeves are not split. That looked more like the sleeve driver. Speedi Sleeves actually work really well when installed properly. Also, there is another seal at the top of the steering shaft that helps keep water out of the tube.
@billclifton8400 3 жыл бұрын
Exactly, in fact it looks like a speedy sleeve is on the shaft but down too far.
@mongomay1 4 жыл бұрын
The bottom o-ring was replaced how?
@mongomay1 3 жыл бұрын
Watched again, now I got it.
@tonygthelegend3621 4 жыл бұрын
Thanks for an awesome video ! Do you know the part numbers for everything you need to do this job?
@JasperMogie 4 жыл бұрын
How did you get the shaft seal out of the column?
@corbinsherrell940 4 жыл бұрын
A long pipe or socket extension run through it. I just flipped it and slammed it on the counter
@dennisvanhoozer3849 4 жыл бұрын
When replacing the seal which direction does it go? Does the spring side go toward the fluid?
@corbinsherrell940 4 жыл бұрын
The lip faces fluid. If you think of a side cutaway view, the pressure will build on one side of it because it wedges itself tighter. If you were to put pressure or fluid on the other side it would just kind of open and push fluid out. This is a good mechanical rule to think about anytime a seal is involved. Some don't matter. Some do. This analysis will always remember assure you. I've put things together "as it came apart" but the older stuff the last guy could have put in wrong. On a hydraulic piston there are lipped seals, several facing both ways because fluid on both sides. To answer your question: down. This particular seal and set up the fluid is below the seal. Thus the top side (smooth and flat side of seal) is up. That side should stay dry
@craigkennedy481 3 жыл бұрын
The spring side is always the "wet" side