Thanks for the info

Unable to remove the 7/16 socket from the racket. Ugh

Curious does this model relearn for camshaft position sensor 2011 jeep thanks

Thanks, very easy to understand.

Thank u Very much

does another brand make this removable version? EZRed version isn’t removable.

That looks 🔥🔥

Hi, Can you tell me what the plug in the bottom is used for mine leaks like crazy makes all kinds of mess Thanks

Thanks for posting. You saved me time researching the spark plug access procedure. FYI; As long as you have the torque wrench hub straight above (in-line with) the spark plug, you do not have to compensate for the added socket wrench extensions. 15 LB-FT of torque would still be correct.

Mike makes this noise when I start then goes away is this a bad pump?

I did this a few years ago and already went bad again. I did drive 100,000 miles in that time but didnt probably torque it to spec

Thanks for the video amigo!!

Dont have great experience with this charger as its basically a color swapped black and decker with a higher jump start (50 instead of 40 amp model). But bench top chargers can be good to keep batteries from dying while working on car electronics with the engine off and reconditioning old batteries. At the shop we use Blue Point and Mac bench tops which are basically Clore automotive chargers andbthe newer snap on bench top with dedicated 30 amp continuous charge. As with all smart chargers, its improtant to know what is the lowest voltage it can detect to begin charging( otherwise they won't work on depleted batteries). Trickle chargers (2amp) can also be good option when storing batteries or vehicles for long periods of time. Some plug in trickle chargers even plug into the OBDII port.

Bought the same exact kit (box and 16 bits but difft sticker) from Matco about 5 years ago. I heard "unofficially" its produced by Irwin. Well now that we don't have a Matco dealer that lifetime warranty seemed pointless. However, when my new Mac tools dealer rolled in the shop and saw my abandoned bit kit he asked if I needed any warranty on it. I informed him it had a Matco sticker on the box. He tore it off and brought me a brand new set with. Mac sticker on it. Yeah he definitely won my return business that day. And the kit is great with the two quick disconnect shanks that can turn a regular drill into an improvised quick release clutched driver.

What if your car is still skipping after the plugs have been changed

Well how has it held up?

Mine came with a broken adapter 😔

Thank you for sharing this video

Did you figure it out Because I’m trying to figure out what the piece does

Oof, tolerances aren’t good eh

Mines makes a clicking sound when charging ...is this normal ??

Ty so much bro

Will this work for transmission axle bushings and seals?

Dorman also makes/supplies a vented cap - Saturn Vue 2.4 used it until 2008.

I just did the same job on my focus but the suspension is constantly bottomed out. Same brand name shocks, but on a 2005 zxw. I guess i have to return them or something.

Followed this step by step and my 2013 is no longer shaking, stabilitrak light is no longer on and runs beautifully. I changed the coils too. In total plugs and coils only cost me $125. Amazing tutorial. Dealership wanted $700 bucks for this to be done lmao😂.

I was just curious, why did you not replace the wires?

That's good if the boot hasn't bonded to the ceramic from heat. Usually the reason they're so difficult to remove is because the rubber boot becomes adhered to the ceramic. The kind of plug boot pliers that allows you to twist the boot causes the bond to break free and you should be able to remove by hand ✋️. Its very hard to get in there to twist by hand, thats why those pliers work great. 👍

What sizes are they?

Big emphasis on the part about not dropping the bolt into the frame. Its basically impossible to get it back out. I found a bolt from menards part number 88287, says its a M10-1.5 Thread, 70 mm OAL, 10.9 Grade. It worked for me so far, big tip is to jam some shop rags down around it if you need to bring the bolt through the access hole but otherwise try and go from next to the engine

i replaced the intake manifold as well since it was only 55$ with sensors and gaskets. but i drove to long with the pcv clogged and the oil was pretty bad because of it now waiting on valve cover gasket and oil pan gasket so we can clean out the sludge this weekend not looking forward to that lol

Just had mine rear seal blowout an had a vented cap can how can you tell if the vent in the cap is stopped up

Rear main already blown. Want to trade vehicle and just need to know if either bars rear main leak stop or atp-205 leak stop is oksy to put in engine to not drip on dealership parking lot.

Do GM mechanics know this? My 2017 Equinox is in the shop now for blown rear main, this is the second time in 13 months, both times in very cold weather. This is a pretty expensive repair to have every winter.

NICE VIDEO. TY

Mine just took a 💩 McGraw 21 Gallon 175 psi Vertical Model. The Electric Motor failed. I 'don't' recommend anyone buy these. In my opinion, they're junk !! Owning mine for about two years. I may use it a half dozen times in a month. Mostly for airing up tires. Sometimes run it with a couple of air tools. But definitely not overworked. Being it was oil free & less maintenance. I gave it a shot. That was a mistake.

How come you spelling the garage with Λ & Σ🤔

What about the circle bushing and little rod? That’s what I need? Does it come in that kit? If not then what’s part# on those?

Thanks

That is ford

holy shit. My 4.7 with 300k+ miles Sequoia doesn't even make that much noise.

Typical GM

Excellent video, I appreciate how you took the time to show how the connectors come off (snaps/pull) as this save's folks the headache of broken connectors due to lack of knowledge and haste. I am thankful you took this time to do the actual work without telling us what kind of race you entered before, your need to explain to us what type of garage and tools you have and the like. It was direct and to the point. Thanks again!

Why didn’t you remove the tire It would be easier

Thanks brother!

Thanks bro..!! 👍😊

A Malibu! Isn't that a front drive engine? What happened chevrolet??

What if smoke comes out from engine after replacing gasket?

is it the same process for the v6 one