It is a good lookin' car man.

What's the wiring like? Can you plug into the original cable?

Much better looking GX and much more clearance for off roading. Thank you for the video and the tips about trimming the rear bumper. What size tires are you running?

Soo Baroo

Thanks for the video very helpful to see your process ! But just a tip ... after you are done with your mods at the end of the video take some B roll to show what the car looks like. Like take some video of it from like 10-15 feet back and film it standing still for like 10-15 seconds. Thats what people want to really see, what it looks like. You kinda just glazed over the finished product

Would you still recommend the Mamba tent? At 250#, I can’t imagine you take it on and off. Not sure why they say it is 177 pounds, but 250 pounds “packed” . One could say the mfr is lying

Where you get the brackets ?

This is perfect, I have a toy hauler and I’ve been wanting something to do off the whence the door is down. This is way cheaper than the stuff they are selling at the RV stores.

Did you go with the flat or angled?

In my line of work and sometimes being miles from a hot shower this and the Coleman hot shower on demand. Is a necessity.

Leave the windows open as you close the tent, that way the air can come out freely, hence the fabrics not trying to stick out

You typically run 2 or 4 boards on the rig?

The ridges in the roof keep the roof ridged. Without them, the roof would have not strength.

It would behoove you if you practice on your video of your vehicle and less of your face

Beautiful setup. What are the specs for your rims and tires again please

Do you think I might be able to get away with cutting the side step without removing it?

Love it broh! I’m jelly

Thank you for sharing Los. Your boards and setup looks fantastic ❤

I bought these to install morimoto 1 bangers and they work perfectly. The only thing is morimoto designed them with a hotspot and cut off line so flipping them upside down messes up the the light pattern 😭😭😭 you can tell the lights are upside down

Stay in school kids !

Bro.. the trash music completely kills the video. Lose the distracting Truckee hipster music

love the energy bro, keep going, youll make it big

the scoop is way too small i wish is ther an aftermarket schoo a little bigger like mustang

Does your roof sag really bad? Im 5'10 and have a 4runner with a 3" lift and 33s and my head rubs the roof because it sags so bad

I came here just say how much I like this company. Our awning room had a small fault. The way how customer service made up for it far exceeded our expectations.

Turn the music down when you’re talking for us hearing impaired types bro.

Hey buddy. I looking the mount on cvt web site. But I think is no available any more. Can you help me to this please. Regards

Boom!

Loving the headlights!

I have great difficulty closing this tent while assuring that the sides are fully tucked in. 67 years old with a little arthritis

*Promo sm*

how tall are you? i’m 6’2” considering one of these. worried about size in there but it’s gonna be just me and a 30lb dog most the time. more concerned about length

That's a good looking suv

Yes, we've got a lot from your videos, especially details of your face. Don't you think people would rather see actual mod being installed and finished than looking at your talking face?

hey did you have to cut anything to put the panel back on with the switch panel installed?

So I'm curious how this is holding for you? Likes and dislikes so far?

I added a toyota usb port to the driver side of the dash by the fuel door button and got a super rigid vent mount phone holder, and used a 6 inch charging cable. It puts the phone just above the blinker lever, in view, but also out of the way. Just close the vent and thats it. And it looks stock!

Thanks. Super helpful. I just picked up the same set up plus the rotopack mount from Craigslist $400.

Carven dump muffler will take care of that big ol tank of a stock muffler

Hey I saw two separate wire on each side when you wiring. Wondering is there a order like the red wire on the factory plug has to connect to one of the wire of the light? Or just connect them randomly.

Nice job and a relaxed attitude got it done!

What is the length and width of the piece that you used?

How did you install without drilling for the C4 ladder?

Can it be mounted with the opening facing foward? Thx

Is there a track along the sides to mount accessories? Can it be mounted with the opening facing foward? Thx

I guess "great customer service" means selling you shit you didn't need like a useless terminal block. SP9100 and a neg bus bar is all you really need. Sure, you may have a thing or two that is independent of the SP, like maybe your winch, but you don't need all those fuses. Its the opposite of clean. Its clutter.

couldn’t you just connect the BD light wiring directly to the OEM connector without adding another connector?

Very rad!

You’re crazy cutting that thing man! Looks rad though 🤘 excited to follow the mods and trips. Nice meeting y’all!