Excellent video. But please get some water hooked up to that saw.. That dust will catch up with you. your gonna work hard for several years, you want to enjoy retirement!

I have a SS 3+ (caution) 7/4-6: I travel to the Wedge (Newport, CA) to get pounded by a southwest swell, but I can't film myself since my camera isn't working and is still with SS. 6/22: SS receives the camera. 6/18: After attempting to remote troubleshoot with the SS rep, and me sending them video of doing what they asked for, I was asked to send the unit back. 6/10: New issue: camera tilts down and just doesn't function. I contacted SS by email and received a response the next day (great service in that respect). 1/22: Received slip that looks like my camera is at the post office. 1/9/2024: On 12/1/23, I sent an email to support because my tag wasn't working, nor charging. I found out, on my own, that I needed to discharge the camera battery so that the camera needed charging. Only then would the tag charge. However, it took 26 days for an email reply to this tag issue. However, the rep asked if I had any other issues and I was able to share an issue that just came up a couple days prior. So, this next issue could be considered a 2-day response. On 12/27, I was notified I had to send my camera in due to issue #2. I sent my camera back on 12/27/23 and am currently waiting for it to return.

Could help me find your video where u installed it

Tripped me out when it looked like he put his toe under the partially but not fully lifted trailer

how much would that cost? half the price of the house?

Great build

Ten yr project

So much cutting 😮‍💨

Well done, in dealing with the added challenges the lipped base blocks presented.

Thanks bro

Excellent work!

Great job pall👍👏👍

Good job looks beautiful

You cant be serious ? That thing dosnt tuck away ? It hangs out like that omg

measurement of seat please,

Thanks

Thanks for the video. Informative. This company is very small to produce a technology like this. They should have sold the company to Sony or Canon when this idea was fresh.

Damn nice looking job. Genuinely looks like more than 400 hours of work there. Well done. 👍

a few years from now, people will look at this and think Aliens built it.

Amazing. I hired a handyman to do my front bricks and it looks so trash.

Honest question. How does the fire pit area drain rain water. Throught mortar lines or a designated spout?

You should wear a face mask when cutting that material.

at 5:11, just out of curiosity, why do the wall joints line up vertically? Looks like you used a few smaller blocks or cut some. Was there a specific reason for that?

Well done!!!!

Saw goes to the shop with dust plugged air filter from running dry with no water.

Best explanation on KZfaq thank you so much

I'm about to do a large kidney shaped pool with funky copping stones and this video helped me Huge!

Very good.

I always wondered how that was done. Far beyond my skill level. You my friend are talented! Beautiful job

Nice work. Did you pour concrete under wall fir base?

Top notch

Hello👋🙋‍♂️ there once again Amazing and very interesting video🎥 as always. Super like👌👌👌 project Good information very helpful🎥 Do keep posting Warm regards and best👍💯wishes The UnknownManCub 👍😎👨‍🏭

To avoid the partial cap, next time try breaking the joints with each cap to be cut. Then stack your full blocks on top of their gaps and use the full blocks to mark the cut lines. Remove your full blocks and cut the marked angles. Glue them all in place and ouala, you've got perfect spacing, perfectly centered joints, consistent sizing and no compensating with random size wedges.

You can cut the face of the cap in one step just don't let the blade go past an inch of each side and tap it out with a hammer. No need to lay it down and make the pencil marks and cuts

Damn, that’s incredible work great job guys!!

Nice job. I would never work with a cap that had a lip like that. Why add that much more cutting to the job when there’s caps that don’t have that?

Beautiful 😍

Beautiful! I especially love the corbels under the bar top. Super nice touch! 🏆

what about outside curves

wtf? i never knew they came apart like that

Great video. When cutting caps for the outside radius wall, do you have to cut the lips or just tuck the blocks together, find the gap distance, cut the gap distance in half, then saw?

Thats the problem, these builds are great but few can afford the price of materials!

For a project like this, what is estimated price? I am in NC and looking at a design similar to this for our backyard

This is THE ONLY video that shows and explains how to do inside radius cuts out many on youtube. Thank you so much!!!!

after watching this video I still have no idea how the two halves are connected.

Beautiful job....

I like how your aren't afraid of dust

Great video. Informative, concise, and to the point...all under 6 minutes!

Absolutely beautiful!

Big thanks 🙏🏽 for this non of the other videos I watched made sense. I appreciate how well you explained the cuts. My geometry teacher is somewhere smiling.