I was wondering how someone was supposed to clean the boilers. I have that same boiler. I didn't realize you needed to remove the entire gas assembly to get to the burners.
@thunderbolt20177 ай бұрын
how did u recondition the pulley ? It was completely rusted. Can you please show us
@-Nobody-17 ай бұрын
Klein makes the best crimps, they are the most widely used crimpers in the industry i have ever seen. Even in Automotive Electrical to Residential Electrical, even too the electronics industry. Just sayin.
@fasttimestr8 ай бұрын
It's a taper lock bushing
@thunderbolt20178 ай бұрын
excellent. Love your videos
@thunderbolt20178 ай бұрын
thank you for such educative videos. Really amazing for people to learn.. your techniques are very professional !! Great Job
@Gretathunbergsfart11 ай бұрын
This guy is def Albo 100%
@brdhus11 ай бұрын
QUESTION: We have several Liebert crac units with water cooled condensers. Currently we use approx 70deg water flowing through the condensers. However, we need to know if we used 55 degree water would it drastically effect the units efficiency. There is a condenser water control valve in each unit. I ask because there are no parameters recommended in the owners manual. Any help here would be greatly appreciated.
@FrostHVAC5 ай бұрын
Id argue and say yes there a possibility it can cause problems. Lower temps lower pressures, and cause evap temps to run a bit lower. There’s a reason units are designed for 85*F for the condenser. 75 sounds better, typically where ive seen lieberts run their water cooled condensers as well
@user-oj2md8zl6v Жыл бұрын
have you cleaned the heat exchangers on these yet
@user-oj2md8zl6v Жыл бұрын
thats what i want to know
@mickey9852 Жыл бұрын
Not trying to be a dick, but a barring heater or even throwing them in a toster oven will make them slide on like a condom.
@CBLAST420 Жыл бұрын
Good stuff brotha 😮
@jeremiasfe11 Жыл бұрын
vamons
@jeremiasfe11 Жыл бұрын
lol
@gearmelugin3424 Жыл бұрын
mmmm chocolate (shown in 4:13 in video)
@samakagi4239 Жыл бұрын
What number is the emery cloth you use to clean the shaft prior to pulling the hub? Also is the locking collor directional that goes behind the bearing...does it have an inside and outside? Thanks for the great information..
@TheRealBearFamily Жыл бұрын
I almost always do all fan bearings at once, that one looks nearly impossible to access the other side
@MrBond-pj5dc Жыл бұрын
Hi,, is this taper lock 55 SF ??
@giuliogemino6407 Жыл бұрын
Add to the confrontation IREGA Spain, a specialist in adjustable wrenches and one of the remaining manufacturers in western world of this specific tool. You can get it e.g. rebranded Channellock US or Wright US or even Virax FR... Once upon a time Bahco (SNA Europe / Snap-on group) were made in Sweden, today they are actually made in Spain. 90% of the adjustable wrenches manufacturing is made in China so most are rebranding of them e.g. Crescent a US brand. Nonetheless there are some interesting exception: Some BAUM made in India and some old GEDORE made in Southafrica probably discontinued.
@luishernandez5394 Жыл бұрын
Can you make more videos on shaft alignment bad ass videos 💯
@luishernandez5394 Жыл бұрын
Good job Martin good shitgood videos emin learn a lot here from your channel keep up the great work! 💪🏼 we do light commercial work over at Pga west in La Quinta California about too change a motor bearing on a 5 hp ballador motor.
@jozzboy8263 Жыл бұрын
Useful video, I’m a power plant operator and this was very useful. Thanks.
@salv638 Жыл бұрын
Just wanted to say thank you you have no idea how this video just saved me on a job where I never did this before and your video got me through it
@titurevvlog Жыл бұрын
Love it....
@smitty1715 Жыл бұрын
I fucking miss this guy. RIP brother
@xxxdpgxxxx138910 ай бұрын
What happened?
@smitty171510 ай бұрын
Not sure to be honest but his company said he passed
@robertpeters9438 Жыл бұрын
Pipelines use "pigs", or"pucks" sent through pipes to scrub them clear. Have you considered if that is an option for your risers?
@robertpeters9438 Жыл бұрын
When water evaporates, what is left is brine.
@daveturbovsky6020 Жыл бұрын
Thanks for this video. It answered my question about how to separate the hub and pulley right off. Awesome.
@mark.r89002 жыл бұрын
Hi, I tried to do a pump down on a carrier condenser but it keeps cutting out 2 or 3 seconds into the procedure. There's are no low or high pressure sensor. What can cause this? Thanks
@josephknapp242 жыл бұрын
Hahahaha click click.. hahaha
@nakiapringley53912 жыл бұрын
Great video brother 💯💯💯💯
@FeralFlatts2 жыл бұрын
A bit late in the game... but wish the part when you take out or put in any of the burners was included. That is what I am looking for.
@jimmyordiz10652 жыл бұрын
nice info bro.thnx a lot
@govindhakke64932 жыл бұрын
Supper.
@llanbull2 жыл бұрын
I really hope you see this, but do you suggest I put a locktite blue for the bolts? My co worker was telling me to use. This is for the Air handler pulley flywheel. What about a lock washer thanks.
@arnoldramos392 жыл бұрын
Nice little bag, the adjustable 🔧 wrenches are nice to; who makes them?
@bruce85722 жыл бұрын
I'd like your opinion on the Emerson 49P11-843 SureSwitch Relay? I am thinking of using these on the condenser units at my home. Thanks, Jenkins A/C & Heating
@bottitabaki30732 жыл бұрын
Hi what GPM stands for? Thanks
@naughtiusmaximus18112 жыл бұрын
1:01 Sully that you!?!?
@naughtiusmaximus18112 жыл бұрын
Thx bro watched your video busted my ass woke up early and was 1st on the rope for about ten years now. Learned a lot the hard way and now I'm represented. TWIY
@greg42722 жыл бұрын
Román kontár meló!
@JJJ-jq3hd2 жыл бұрын
how many times this should be done in a month?
@anbusquad74212 жыл бұрын
We are having problems with the make up line the guy who is here to turn everything off doesn’t know where it is
@goonzsquad12 жыл бұрын
Yo I have a question, if I wanna replace a bearing, how do you measure the old one? Or do you just get the middle and serial of the unit and give it to your supplier ?
@naughtiusmaximus18112 жыл бұрын
Still the Best! Thx Emin
@jimdefilippis96302 жыл бұрын
Very cool video. love the old equipment. Never seen a cooling tower that small and in an attic.
@thesco415102 жыл бұрын
Someone greased the shit outta those bearing
@NytefogNJ3 жыл бұрын
You shouldn’t Meg a inverter compressor. You can destroy it.
@anangsetiawibowo68603 жыл бұрын
He's passed away guys
@smvideonow3 жыл бұрын
Fuck that. Obviously don’t cuss In front of customer. Be yourself in the videos. If your making videos for other mechanics cuss away. If your audience are customer then yea clean it up. Stay real.