I have a question about my skoda Octavia 2 maxidot menu how do I unlock the convince menu?
@psykotryp24 күн бұрын
Men i have the same problem as you (steering wheele wont work ) but my radio is compatible what can i do
@GR-jo9zrАй бұрын
I added cruise control too after the multifunction steering wheel thanks to you I love u bro 👊
@ercantopuzogluАй бұрын
nice
@capatinabogdan3395Ай бұрын
Salut ovidu! Vreau să montez pe o skoda Octavia 2008 4x4 1.9 bls cruise control. Ce piese îmi trebuie în afară de semnalizarea schimbată cu una cu pilot ? Mulțumesc
@OvidiuMarinАй бұрын
Salut, am zis in video. Conteaza ce versiune de steering wheel control module ai.
@capatinabogdan3395Ай бұрын
@@OvidiuMarin mersi de răspuns! și totuși cum aflu ?
@capatinabogdan3395Ай бұрын
Am înțeles ca dacă ai computer de bord s-ar potrivi. Adică dacă vezi consum, range șamd
@ALIHxT2 ай бұрын
I believe ive got the same issue, when joining back the wires do i have to disconnect the car battery?
@OvidiuMarin2 ай бұрын
Hi, yes. Are you subscribed to the channel ? If not, would you consider doing it ? Thank you !
@GR-jo9zr2 ай бұрын
I made mine completely working just with the plate I didn’t need to code it but I have hard steering and a steering wheel light on how the fuck I fix that hard steerign
@OvidiuMarin2 ай бұрын
Turn steering wheel to maximum left for 10 seconds, then maximum right for 10 seconds, then centre it, sometimes you have to drive the car for a short distance. If that doesn't work, there's a vcds procedure you need to do.
@GR-jo9zr2 ай бұрын
@@OvidiuMarin i tried but didnt work the car has the same orange wheel light and steering wheel is hard like a mechanical one why that happened because i changed the plate?? i need vdcs coding i think
@OvidiuMarin2 ай бұрын
Which plate have you changed ?
@adrianionutporojanu3 ай бұрын
Salutare, felicitări pentru acest proiect! Sunt pasionat de apicultura și aș vrea să-mi construiesc și eu acest tip de cântar, ati putea să-mi dați și mie librăria pentru arduino, contracost bineînțeles.
@OvidiuMarin3 ай бұрын
Salut, mulțumesc! Lasa-mi un email si iti trimit libraria si cod-ul.
@robertscott19864 ай бұрын
Hi there is it possible to buy the jlink upgrade off you please.
@OvidiuMarin4 ай бұрын
Hi, sorry, not possible. Just get a segger jlink.
@ghatz4 ай бұрын
thank you for the video. I did the whole process and also the coding. When viewing the live data from the steering wheel controls and the module using the buttons of the cruise control stalk I can see the values changing so everything is well connected and communicating with each other. But I get the fault p0568 in the engine module. Do you maybe know why that could be happening?
@OvidiuMarin4 ай бұрын
Thanks for the feedback. Unfortunately I can only guide you to check the rosstech wiki, usually they give good solutions.
@paulstir4 ай бұрын
great work ,well done ,very informative video
@OvidiuMarin4 ай бұрын
Thank you very much for the feedback, I'm glad you find it useful
@Graveyardprintshop4 ай бұрын
trash printer mine has been dead for 2 months just go bambu
@OvidiuMarin4 ай бұрын
So what are you doing with it ? You'll just leave it to collect dust ?
@Graveyardprintshop4 ай бұрын
@@OvidiuMarin pretty much. got an email from creality today. apparently they have new and old mother boards for the k1 max and they sent me a newer version which i guess isnt compatible with my older k1 max.
@_JosephLinsunGelrajJ4 ай бұрын
Can i retrofit octavia mk1 wit MFSW and rcd 510
@OvidiuMarin4 ай бұрын
I think it's possible, but will require few modifications if you want everything to work.
@lazar52645 ай бұрын
Passat b6??
@OvidiuMarin5 ай бұрын
Nu merge. Doar la b6 facelift si b7
@simaalexandru63346 ай бұрын
Salut,la passatul meu cred ca nu are maxidot....si daca iau alte ceasuri cu maxidot...cred ca nu va merge daca masina nu este adaptata cu maxidot
@OvidiuMarin6 ай бұрын
Salut, poti sa iti iei ceasuri cu maxidot si sa le adaptezi. Din ce an e ?
@simaalexandru63346 ай бұрын
@@OvidiuMarin 2002
@OvidiuMarin6 ай бұрын
Poti sa iti iei ceasuri cu maxidot si programezi immo. Daca nu ai computer de bord din fabrica, mai trebuie sa tragi niște fire.
@simaalexandru63346 ай бұрын
@@OvidiuMarin asta trebuie sa o facă cineva care stie
@zamlata74007 ай бұрын
Hi man, I have VCDS, my octavia 2006 pre FL. It has board computer. Do I need anything else except cruise control handle?
@OvidiuMarin7 ай бұрын
Hey man, have a look at the software versions and check against your steering wheel control module.
@MohitGharat7 ай бұрын
Bro you just changed the country for ecu that could hurt the engine. Instead use security access first the open up google translate camera and go to modules where you can individually control those items. Just changing the country code in ecu is easy but it might change the power and torque as per region. And if the car is not shipped stock with the physical equipment required to sustain that countrys engine map you could potentially brick your car or reduce engine life span drastically
@OvidiuMarin7 ай бұрын
Hi bro, I think this is the only way to make it work. But your theory doesn't sound bad, I'll do some research. Thanks
@igronus8 ай бұрын
How do you think, is it possible to have Adaptive Cruise working there?
@OvidiuMarin8 ай бұрын
I could work, but it will be a tedious task.
@MrBegasoss8 ай бұрын
Why you are fucken hurry
@camaroboy3839 ай бұрын
First layer is definitely to fast.. But, in the experimental tab.. look at the gcode z offset setting.. they are -.05 from the factory.. I found - .04 is much better.. -.03 was to tight towards the back of the bed.. You can add flow to the initial layer, mine is up to 108%... The first layers are much better.. hope this helps..👍
@OvidiuMarin9 ай бұрын
Hi, thanks for your advice. I've slowed the first layer down to 100mm/s. Regarding the z offset, there are areas of the bed where the first layer is perfect, and areas of the bed where the nozzle is either too close , either too far.
@camaroboy3839 ай бұрын
@@OvidiuMarin I'm experiencing the exact same issue.. that Is how I found out about the z offset setting In the slicer.. I suspect these beds aren't completely flat, and most likely the reason the z offset was -.05 by default.. it's unfortunate there isn't a mesh we could adjust on the fly to compensate for slight bed warp..
@yazhtechnologies83169 ай бұрын
It worked, thanks for sharing😊
@OvidiuMarin9 ай бұрын
No problem, glad it worked. Can you please subscribe?
@marcellmanyik56399 ай бұрын
Hi, my homemade cruise control is working perfectly but the criuse control led on the dashboard not working. Why? I forgot turn on on the vcds?
@DGxCraZe9 ай бұрын
You tried slowing down the printing speed Ovi?
@OvidiuMarin9 ай бұрын
Well, it is supposed to print at high speeds. Specially PLA. But I did try, it's a warped bed issue, and for some reason the software doesn't compensate for the Z offset values for every point of the probed bed mesh.
@DGxCraZe9 ай бұрын
@OvidiuMarin ah I were thinking it were a too high print rate for the nozzle size. Have you done any flow calibrations.
@AaronWoodburn9 ай бұрын
human error.
@snakejump769810 ай бұрын
Have you found out the problem?
@OvidiuMarin9 ай бұрын
Someone suggested to modify the line width to 0.38mm, which kinda worked, but I will also print the lid riser and do the cable chain bowden clips mod. And I will print the TPU bed spacers. Also, creality is sending me the new extruder.
@andybaldman10 ай бұрын
Congratulations, you played yourself.
@snakejump769810 ай бұрын
You could try printing out cable chain Bowden clips and a lid riser to see if that fixes the issue, There’s models on printables you can download. The clips and lid riser can help with under extrusion on the k1
@OvidiuMarin10 ай бұрын
Thank you, I'll give that a go. But, in my opinion, for the amount of money that K1 Max costs, you would expect to be plug and play, without any tuning/mods etc.
@snakejump769810 ай бұрын
Goodluck! I hope that works for you. I 1000% agree!! At that price it should be ready to go right out the box
@musaali15810 ай бұрын
This is most likely under extrusion. I use 3d printers but I am not an expert in the field but I am very sure this is under extrusion. If you look up images of under extrusion they look like your print. This can be caused by many factors such as nozzle cloggs or extuder jams.
@OvidiuMarin10 ай бұрын
I thought the same, but it's not evenly across the bed. On some areas, the lines are fused together as one ( no gaps at all ). Which makes me think the mesh bed levelling doesn't compensate for warped bed.
@will-dd7ou10 ай бұрын
@@OvidiuMarin do a higher leveling density, make sure nothing is under your bed, mesh level the bed at temp, make sure your nozzle size is the same as the one in the slicer and on your printers, and then fully do a z axis leveling by printing out a 1.5" strip that goes across the entire y axis of your printer
@lobby606610 ай бұрын
probably the fiment
@_param10 ай бұрын
R u printing with support filament?
@OvidiuMarin10 ай бұрын
No, support not needed.
@valentinlazar204910 ай бұрын
Salut cum naiba am cumparat vreo 5 de pe aliexpress si toate se vad doar pentru cateva secunde si dupa începe sa se vada intrerupt si dupa dispare tot
@OvidiuMarin10 ай бұрын
Salut, inseamna ca problema nu e display-ul. Ar putea fi ceva pe placa
@valentinlazar20498 ай бұрын
Nu cred ca este de la placa, am probat si pe alte maxi-doturi.. toate de passat b5.5
@OvidiuMarin8 ай бұрын
Am înțeles... nu știu ce sa zic..
@valentinlazar20498 ай бұрын
Ai un whatsapp, iti trimit un video
@OvidiuMarin8 ай бұрын
Da-mi pe insta ovivlogs01
@jonathanhutchins10 ай бұрын
Hi, I have a 2012 mk2 superb. The CCS retrofit kit comes with an extra wire to go to the ECU I assume? Did you not need to do this for yours? Thanks.
@OvidiuMarin10 ай бұрын
Hi, it was not needed on mine. The seller should've provided you with an installation procedure manual. Have a look online, I'm pretty sure there should be a guide for it. If you can't find it, let me know.
@jonathanhutchins10 ай бұрын
@@OvidiuMarin Thanks for geting back to me. I have yet to purchase the kit and it does look to come with an instruction booklet. I have just been researching the process before purchase because the official kit is expensive and I don't particularly want to have to mess with the ecu wiring on install. Also did you use an obd2 to usb cable for vcds or one of their wifi/bluetooth obd2 dongles?
@OvidiuMarin10 ай бұрын
You need vcds or anything that can access the ecu and activate the cruise control.
@hassanraza100910 ай бұрын
Hello
@OvidiuMarin10 ай бұрын
Hi
@tdnoz Жыл бұрын
Hi, is this all you have to do to make Cc Work? Im are about to retrofit this and a MFSW ++ to my car
@OvidiuMarin Жыл бұрын
Hi, yes. Good luck doing it ! Don't forget to subscribe to the channel if it helped you. Thanks !
@thecoolguy9364 Жыл бұрын
Do you just hold the button??
@OvidiuMarin Жыл бұрын
Yes, but it needs to be programmed first. It only works on certain types of comfort module.
@gihadmagdy6153 Жыл бұрын
U Programmed it through vcds or another tool
@OvidiuMarin Жыл бұрын
Another tool
@danielanac5093 Жыл бұрын
te rog, o adresa de email unde iti pot scrie?
@user-qb7uq9dj1u Жыл бұрын
Thank you for making this, brilliant video exact same issue on my vehicle
@OvidiuMarin Жыл бұрын
I'm glad it helped you. Can you please subscribe ?
@zcfasd Жыл бұрын
I had the same problem , did not had the time or the patience for it I've cut it away without removing anything .... its been a year since ! 😅
@OvidiuMarin Жыл бұрын
I wanted to do the same thing, but ended up buying new ones. I've also changed the one on the opposite side, as it was only days away from failure
@dirtyaznstyle4156 Жыл бұрын
Meh what’s a few rocks in the caliper and grease from the ball joints?
@oisin5349 Жыл бұрын
Thanks for the video. I have a newer Octavia from after 2009. It has some extra buttons on the steering for controlling the radio, phone calls etc. Would that make much difference, like more wires, or is it basically the same?
@OvidiuMarin Жыл бұрын
Hi, thanks for the comment. It's basically same thing, you need to look for a highline steering wheel controller. You need the XXX-953549-XX version, so 2 digits at the end
@DecentralEyes Жыл бұрын
Your audio could do with compression and EQ boost around 1K
@OvidiuMarin Жыл бұрын
Thank you for the feedback! I'll keep that in mind on my next videos.
@PointWF Жыл бұрын
Tanks 🫶
@OvidiuMarin Жыл бұрын
You're welcome
@mohammedmahmoud615 Жыл бұрын
the file of "V8 firmware no serial" was deleted from the site. could you upload it again, please thanks
@OvidiuMarin Жыл бұрын
Sorry, don't have the file anymore.
@radu1459 Жыл бұрын
Salut , doar trebuie schimbat calculatoru de coloana cu unul highline? Sau trebuie si codat calculatorul? Eu am midline si vreau sa pun si comenzile pe volan .
@OvidiuMarin Жыл бұрын
Salut! Pentru comenzi pe volan trebuie sa ai calculator highline. Apoi trebuie codat pentru masina ta.
@radu1459 Жыл бұрын
@@OvidiuMarin Deci trebuie codat pe masina calculatorul highline?
@OvidiuMarin Жыл бұрын
Da, orice modul schimbi, trebuie codat. Sau măcar verificat coding-ul. Pentru ca nu știi de pe ce masina l-ai luat si nu știi ce functii sunt sau nu activate.
@radu1459 Жыл бұрын
@@OvidiuMarin Poti sa ma ajuti cu un link ca exemplu cum se codeaza?
@OvidiuMarin Жыл бұрын
Depinde de la masina la masina. E destul de simplu. Intri cu vcds pe calculatorul pentru coloana volan si intri in coding. O sa iti apara un mesaj cu toate informatiile necesare pentru a efectua o codare corecta
@radu1459 Жыл бұрын
Salut pe mine cu vcds lite nu ma lasa sa intru la steering wheel, sa fie din cauza ca e lite?
@OvidiuMarin Жыл бұрын
Salut, dacă ai vcds lite, da. Un subscribe?
@radu1459 Жыл бұрын
@@OvidiuMarin Dar is aceiasi pasi si coduri si pe golf 5 nu? Ai subscribe.
@OvidiuMarin Жыл бұрын
Aproximativ. Scrie-mi aici dacă ai probleme
@dragosturcu9959 Жыл бұрын
Pe rcd 510 merg comenzile pe volan de la octavia 2 nfl?
@OvidiuMarin Жыл бұрын
Nu stiu sigur. Mie nu mi-au mers cu RNS510 ( RCD510 e cam același lucru ). Mi-au mers cu radio original de skoda. Poți incerca
@giuliageorgevici336 Жыл бұрын
Buna ziua! Cum as putea lua legătura cu dumneavoastră? Am niște întrebări. Mulțumesc!
@markanthonynilo9198 Жыл бұрын
I tried this code in tinkerCAD it worked. Thank You. #define front_led_sw 2 #define front_led 3 int front_led_sw_state = 0; int front_brightness = 0; void setup() { Serial.begin(9600); pinMode (front_led_sw, INPUT); pinMode (front_led, OUTPUT); } void loop() { analogWrite(front_led, front_brightness); front_led_sw_state = digitalRead (front_led_sw); if (front_led_sw_state == HIGH) { front_brightness = front_brightness + 63; } if (front_brightness > 255) { front_brightness = 0; analogWrite(front_led, front_brightness); } delay (100); }
@OvidiuMarin Жыл бұрын
No worries. Can you please subscribe to the channel ? Thanks
@RazArtistBlockEight Жыл бұрын
Salut bro, I have found your Chanel recently as I am doing a MK3 steering wheel installation on a MK2, I so far have the wiring loom, steering wheel & airbag of course. Was just requesting your option do I need any other parts? For context I only want playback options such as forward song etc and volume control I am not fitting cruise so I shouldn’t need the control module is what I understand? MFSW Loom part number: 3V0971584A Any advice is appreciated
@HckrTeam Жыл бұрын
Thanks for your video and work ! I'm on few automotive forums, I would like to ask you, what do you advice to use for reading mcu or do prog stuff, vvdi ? Carprog ? and why ? For the moment I use the T56 Universal programmer (successor of TL866 gen and + models) to read EEPROMS. The fact is I want to go further, I just do little stuff to help family and friends with some obd specialised program and diag without needing to read/write .bin, but I'm want to do more 😁 Thanks 👍🙏
@OvidiuMarin Жыл бұрын
Hi, thanks for your comment. Throughout the years, I've found that if you don't have genuine tools, it is better to have access to a multitude of tools, I have xprog, vvdi, carprog, tl866+. Most of the time, I use vvdi and TL866+. Please subscribe to the channel. Thanks 😊