14 күн бұрын
21 күн бұрын
28 күн бұрын
4 ай бұрын
7 ай бұрын
7 ай бұрын
7 ай бұрын
7 ай бұрын
8 ай бұрын
8 ай бұрын
8 ай бұрын
9 ай бұрын
10 ай бұрын
11 ай бұрын
11 ай бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Пікірлер
@brianritchie75 16 сағат бұрын
$1000 ICC sensor and $200 worth of ADAS calibration here. Guess he left that part out
@user-gn8zr1gr3w Күн бұрын
Is it possible to drive with a faulty sensor or does it affect the ride
@vikmarquez 2 күн бұрын
You could do that from the bottom and not remove all that stuff that you did. This is like the hardest way possible. I’ve done it.
@timzauto Күн бұрын
Yeah I've done it from the bottom also,a lot easier from the top,took me 10 minutes to get it off,thanks for watching.
@lucyguerrero2791 2 күн бұрын
What's the tool you used to take the belt off please
@timzauto Күн бұрын
www.amazon.com/Powerbuilt-648451-Serpentine-Belt-Tool/dp/B004KED77A/ref=sr_1_9?crid=5MKB3P74DOTW&dib=eyJ2IjoiMSJ9.ii7kOXQObAzr-8Yp5-BsetQu_P9dctEhz1RS-Eg8DEyq2g4P7IrsSU7SM_UD3wzjzCt8o-yeWXJhHAZaW72cC-MfJXYtNkliiiYa6Rsigi7l-YRQFEL6wIDqupoMeA9F9kw6eTROaT68zt_aT3JKgCAZxLwHboA6FELmfk0lqTE_3U2DgLcdyOVFnpt9Z_jM4GH8ctKHoPMfrpgQRBFEKnzCDgOojKbSYfkhiKQeqasw1oHJaPJk2X_pvUTqAX558UkxcZlQXJohZIhC1YyiLztE3C3XDYTnbak0nF3dnXs.HffKR1W7u5KJ1cUOuG-RF6M4MmNenhzJGVZ_1lag-hE&dib_tag=se&keywords=serpentine+belt+removal+tool&qid=1724063691&sprefix=serpentine+belt+removal+tool%2Caps%2C137&sr=8-9
@davidbachy5627 3 күн бұрын
2014 has no slack on the wire so you have to remove the screw prior to taking it out. I had to use a very thin wrench, like the kind that comes with an office chair.
@myst1cull 4 күн бұрын
You rock, thank you
@clawhammer704 6 күн бұрын
This is a heck of a lot easier to get to than the 2007 Buick rendezvous 3.5 crank sensor.
@timzauto 5 күн бұрын
Yes it is,thanks for watching.
@Mid-Ohio 6 күн бұрын
Great video imma try your way compared to the other videos out there.
@JdsjsKdmem 7 күн бұрын
Warm then cold? Thats what mine is doing
@mattgoodman6161 13 күн бұрын
Tim my expansion valve is installed vertically vs the horizontal mount shown here. It is a 2002 CRV and it was built in Japan. My question is this: is it basically the same removal (it appears it would be) and is it the same part that you had used? if unsure how would I go about finding that info in order to order the right compressor/condenser and expansion valve? Much appreciated!
@timzauto 13 күн бұрын
It's the same,doesn't matter if it was upside down,lol.
@OG213LA 14 күн бұрын
Did you change the o rings?
@timzauto 13 күн бұрын
Yes always.
@ATFBRASIL 20 күн бұрын
What DTC please ???
@timzauto 20 күн бұрын
PO335
@lorenzocosta9992 20 күн бұрын
Hey I know you are located in Georgia can I ask where? I would like to hire you for a ac servo motor on a sequoia 2010 please
@timzauto 18 күн бұрын
I'm in North Georgia,near South Carolina,doubt you'd come that far,lo but thanks for watching.
@user-sq4ed7iv3q 21 күн бұрын
Are you using S.A. E tools on a metric car?
@timzauto 21 күн бұрын
O yes, sometimes that 3/4 fits tighter than a 19mm 😎
@eddiemartinez3634 22 күн бұрын
Thanks bro.
@FaustoDiaz-yo1ek 23 күн бұрын
Where I buy I try to get one I just can find one
@pawansharma-iu7me 24 күн бұрын
Hi mate, i have nissan juke 2021 , it’s showing collision warning with gearbox fault( exact warning is gearbox fault stop safely call dealer). But when i turned off emergency brake setting , the gearbox fault doesn’t come on dash. So i think the warning of gearbox fault is just a bad signal happening due to faulty collision warning . What you say ? Thanks
@timzauto 23 күн бұрын
I wouldn't what to tell you without diagnosis it myself,I haven't came across this warning yet,but I despise Nissan's CVT transmissions, that I do know.And you know what Nissan says that's just icing on the cake"In today's marketplace CVTs can be expected to provide reliable operation up to about 100,000 miles then you have to get them rebuilt or replaced and they are even used very expensive.
@pawansharma-iu7me 22 күн бұрын
@@timzauto Thanks for replying mate . Today my car (Nissan Juke 2021) didn’t get started and the warning was “gearbox fault, stop safely and call dealer” . It has only 80k miles and last month they had to replace the whole new engine. It’s frustrating when you buy brand new car and this thing happened within couple of years. What do you think about gearbox fault ?
@timzauto 22 күн бұрын
@@pawansharma-iu7me my honest opinion and I will tell everybody this,do not buy anything but a Toyota or Honda right now.
@mr.mechanic8166 25 күн бұрын
Name of tool
@timzauto 25 күн бұрын
www.ebay.com/p/661750086
@Texan1 25 күн бұрын
Will this fix a p0300 code We already replaced 02 sensors,injectors,high pressure pump,maf,map,plugs,coils vvt,exhaust solenoid, compression is 210,190,210,210 left to right
@timzauto 25 күн бұрын
How many miles on it?
@Texan1 25 күн бұрын
150k
@timzauto 25 күн бұрын
Plz tell me you've done the timing chain?
@Texan1 25 күн бұрын
Yup and water pump
@timzauto 25 күн бұрын
@@Texan1 that pcv system I show how to may fix your problem. A malfunctioning PCV valve can disrupt the air to fuel mixture causing a misfire code,only a few other things will also,including a leaking head gasket,it will show random misfire because the coolant is getting on the plugs,happens every time.but you have good compression readings besides the second one down 20
@luisalejandrosalazar3145 29 күн бұрын
Greetings. After replacing it, did you have to reprogram something? Or was it just a matter of removing the old one and installing the new one?
@timzauto 28 күн бұрын
I didn't have to recalibrate it,but if it was in an accident you have to,the car is not the same anymore.
@CollinBoddy Ай бұрын
Experiencing the same issues good stuff, gunna go grab a new one 😊
@ianm5908 Ай бұрын
You should always empty the oil out of the old one then empty the new one and put in the amount that's was in the old one...When they already have oil in them it's usually to much and it'll chock the system with to much.
@timzauto Ай бұрын
No you don't have too,I have a chart with all the vehicles freon and oil capacity,don't ever just match what's left in the system,could have leaked,evaporated, etc.always look it up and use the correct amount and type,hope you've learn something and thanks for watching.
@AniseMarieCarter Ай бұрын
When I attempted to push down and pull out the individual wire I got resistance? Any assistance is appreciated thank you
@timzauto Ай бұрын
Make sure it doesn't have the red safety clip,if so just slide it up.
@Cobra2000gtl Ай бұрын
I would just make a switch $3
@IamSystemsbuster Ай бұрын
I WISH YOUR VIDEO CAME UP FOR ME ON KZfaq. THE ONLY WAY I found this was searching Google first. Thanks for the direct, easy to follow non rambling, video!
@sonyaramos2528 Ай бұрын
Nice!
@Slim252 Ай бұрын
Will the 2003 Tahoe still drivable if I remove the small belt that’s attach to the ac compressor and the crank shaft pulley?
@timzauto Ай бұрын
Yes,it only controls the ac compressor it will be fine.
@Slim252 Ай бұрын
@@timzauto ok thx
@schifoso Ай бұрын
Really good tutorial. Clear and concise. Thanks!
@ianm5908 Ай бұрын
Not so much read my comment.
@tjd1121 Ай бұрын
Great video, and helped me a lot, saved my night actually, god bless you. And also found that needle nose worked to spin the caliber.
@timzauto Ай бұрын
Did you put the rear emergency brake in service mode?
@user-bo7bz8on7s Ай бұрын
Hi! ! How much oil should be poured into the compressor?
@timzauto Ай бұрын
Different systems have different amounts,look under the hood for the A/C specs,freon,oil,etc,I used 4 ounces of pag 100 on this one.
@joncturner Ай бұрын
I was completely skeptical. I got this car from my mother in law because she was taking to a mechanic because the p0420 code kept coming back. The cat was only a year old had new o2 sensors. I ran two different cat cleaners through the tank. Still came back. I came across your video as I was about to do the spark plug non fouler trick. I swapped out the really corroded spark plugs for new iridium and error gone.
@bankrollfresh6278 Ай бұрын
Hey mines ran hot and won’t start it cranks but won’t start could it be my starter or this problem?
@vandall0160 Ай бұрын
Thanks for the video, about to embark on this on my '07 Tundra, and was just quoted 7 hours labor at the local shop, and they were reading off the book where as they remove the entire dash and steering column. $900 in labor alone, so I thin I will break out the tools and a sweat rag now that I see it can be done without removing everything but the carpet!
@timzauto Ай бұрын
All I can say is good luck,because getting it back on all lined up will test your patience,lol.
@shawnspeigner2835 Ай бұрын
Did you just pull the lines out from the top right and let them drain that way?
@timzauto Ай бұрын
No I used my recovery tank before I started to get the freon out,but it had a leak and there was hardly any freon in the system,thanks for watching..
@terrancewilliams138 Ай бұрын
Dont look as hard as I thought it might be
@timzauto Ай бұрын
Piece of cake 🥮
@michaeljohn7412 Ай бұрын
I had a question I have 12 Altima with the 3.5 and when I search up for crank position sensor it shows there’s 3 different locations? Did you just change this one or is there more. Thanks
@timzauto Ай бұрын
You only have this one crank sensor,you also have 2 cam sensors so in all 3 sensors for the timing control.
@madelinecruz2802 Ай бұрын
I have a Nissan Rogue 2019 and I'm having the same problem and honestly don't want to spend the hundreds at a shop or dealer. Where can I also buy a replacement sensor?
@timzauto Ай бұрын
I bought this one on E-Bay,good luck..
@Aridorable109 Ай бұрын
Nissans are terrible
@parkerstephenson2172 Ай бұрын
I am experiencing this problem with my 2018 rebuilt Nissan maxima. However when I look behind the front bumper and logo or my car I am not seeing this sensor anywhere in the car. Help!
@timzauto Ай бұрын
I think on the Maxima the sensor is on the passenger side front lower bumper near the headlight.
@gregsmith332 Ай бұрын
That axle nut was supposed to be torqued to 229 ft lbs using a torque wrench, not 1,000 using a impact That's how you get wheel bearings to fail prematurely.
@timzauto Ай бұрын
No it isn't, wouldn't matter what you torque it too, it isn't going to "all of of sudden" wear out because it's too tight,give me a break wheel bearings wear out because of Movement,Miles,and quality of the product.Stop believing your little buddy's at the oil change shop..
@aliwooz913 Ай бұрын
I swear people must just turn the volume up on their radio to tune out car noise. How do you not notice that
@matthewisherwood7517 Ай бұрын
Couple questions 1. Did you have the coolant vacuumed out prior to removal? 2. Did you take it to an AC place to recharge after? 3. What kinda oil goes in those things?
@javierpaez613 Ай бұрын
Thanks ,I been having that problem on my 2019 altima.
@thecomptonpoet1 Ай бұрын
Thaaaannnnnk yu
@timzauto Ай бұрын
Your welcome,thanks for watching..
@captain052A Ай бұрын
How is it holding after 2 years
@FranciscoHernandez-fg2od Ай бұрын
Good stuff sir, thank you for the video
@captain052A Ай бұрын
How is the cooling of this compressor compared to oem? Aftermarket better?
@timzauto Ай бұрын
Works the same.
@stevenparker1063 2 ай бұрын
what were the symptoms? I had a huge intake backfire from starting fluid, and I suspect an intake problem, car will not even start tries to but just stumbles and backfires
@timzauto Ай бұрын
It should start with the intake off,you might have other problems,timing ,crank sensor etc. check those.
@stevenparker1063 Ай бұрын
@@timzauto thank you. Ran fine b4 backfire cps is ok
@timzauto Ай бұрын
@@stevenparker1063 backfiring is lean condition,since you don't have a carb I would suspect timing jumped.
@stevenparker1063 Ай бұрын
@@timzauto as in timing chain slipping?
@adamoventrop9105 2 ай бұрын
Bumper does not need to be removed a 12" electrical screwdriver is used to turn the clips for the grill. For reinstalling remove clips from body re install on grille, snap grill back into body. I was wondering why the book only pays 1.4hrs.
@timzauto 2 ай бұрын
Took me less than hour removing everything I did with a snack in between too,do what you do,thanks for watching 😎
@ronhat-nx6yq 2 ай бұрын
This video is a waste of time!!!