Excellent work! I learned quite a bit thanks!

Does it remove light scratches from aluminium?

Dude you're an amazing human being, humble but radiant in your passion and pride in your work. Thank you for all of the great information and advice. My question is: how much did you charge for that job on that 20' center console, for wash, wax, and hull included? Also, what do you use for the glass and plexiglass?

You the best 😎

Magic erasers have bleach in them.

You’ve got the best vids brother

I like the fact that you use Castro Super Clean, I love the product, and i've been using it for over 30 years. In my opinion, it's the best cleaning product on earth as far as cleaning grease, grime, mold all most anything, you name it. But I give a warning to people reading this post. Do not ever use Castro Super Clean on aluminum because it will eat it..✌️

hey drake any recommendations on insurance for $1mil policy. like who to go with?

Would you recommend doing all the steps in a section and then moving on? Or could I Do step one, one day then step 2 the next day, and so on? Great videos!!!

So where did the little pieces of rust come from. Scrolled through the video couple of times and never heard where the metal came from that caused the spots?

Have you used Ardex VG? How does it compare to the Marine 1000?

So I can take off the seats of my jetskis and water can fall into and it’ll be fine right? Thanks

private boat owner of a 2006 21 foot parker cc. Thanks for all the guidance on how to get started on proper maintenance. Planning to finally take a shot at compounding and waxing/sealing. I have a couple chips in the gel coat. I live in southern ca, coastal community. pretty moderate weather, stored on a trailer. What PSI is safe for initial pressure washer on this gel coat, what pressure washer tip used, and would having chips in the gel coat prohibit using the pressure washer at that PSI?

Amazing. I wish you guys were close to me!

Imagine that, taking time on the details while detailing a boat, who would of thunk :o)

Is there any problem using beadlock ceramic coating after the wake-up instead of Daddy-O.

Man it’s to bad you aren’t in the Houston Texas area. You are a true master of your trade. Love the way it turned out. I have a semi- heavily oxidized 1979 mark twain that I’d like to get done. Thank again for giving out and mentoring some of you knowledgeable step by step expertise for free here on KZfaq. Take care bud.

Sabre's are gorgeous. Would love a full vid of this "revival!"

Will this same process work on a RV or trailer that is gel coat and heavily oxidized ?

You should try using a foam roller. I’ve been doing that for many years and it spreads on more evenly than any other method I’ve tried. I’ve maintained my boat with teak wrapped gunwales, teak sole and teak trim. Comes out beautifully every time. 👍🏼 Great video though, love your work bud!

That's a crazy transformation. Would never have believed it was the same boat.

Okay, so I’ve been doing details for quite a while, but details are not our main source of work. We own a yacht repair service on the Mississippi gulf coast so we do a little bit of everything and sometimes we pick up a few details here and there. I have a potential detail coming up that’s a 1.25 mil dollar Bertram. I’m going to do a few test sections on it today as I’ve already spoken with the customer. She was very dissatisfied with the past three detailers, typically this points towards a PITA customer but this doesn’t seem to be the case. The detailers just did crappy work point blank. She tells me that after having the boat “ceramic coated” , one of their guys they hired for a detail used a pump up sprayer and sprayed simple green ALL OVER THE BOAT!!! 🙄🤦🏻‍♂️. My question is on the over hang on the bow where the cabin space hangs over the front deck there is some pretty nasty “yellowing, almost a brownish tint to it” in one section. I’m not sure what that is and I’m going to attempt to see if I can try a small section of it out that’s unnoticeable to see what I can do to get that out, may wind up having to wet sand or try something different. I know it’s hard to tell without putting your eyes and hands on the surface area , but what are your takes on it? Thanks Drake! Michael Norman Norman Yacht Services

This is your best video yet! I have a 2003 performance boat in Lake Havasu Az. No one can believe it’s 21 years old. I’ve been following your video to keep it looking as nice as I can. I have a friend that boat a used boat (5th owner) that needs some TLC. I think we will be using all of the steps in this video to make it pop again. This is your best video yet. Thank you for sharing.

Hey drake I have a question these west marina mop head aren’t good tp dry boat what you recommend

That's a job to be proud of! Excellent work!

What did this cost.

Do you still offer boat detailing classes? I did not see it on your website.

Wow!! Nough said.....

How much did you charge for that including the polish?

Very informative video, sincerely apreciate the effort involved in sharing this! I have a similar Duckworth with some pretty bad dock rash/scraping/burrs (previous owner). Any suggestions on removing them?

Invest in a long throw random orbital. It will eliminate all the swirl marks you left behind. Will leave a more professional appearance.

The star ninja works amazing from shine supply and is safe to scrub my 2020 lsv23 has that two tone texture vinyl and it’s a pain. The ninja is awesome . Love your videos and the recommendations

Just wow

Do you have a boat detailing training camp?

I’ve been detailing for a little bit now. Had a customer that wanted a boat done never done a boat before. Are you allowed to get the gauge bezels and everything wet for mould and mildew black seats? What’s the best thing?

Not smart to not tape up. What happens when you rush a job

Insane!

Hi Drake, thanks for valuable info. Could you also dry sand it? Or it needs to be wet sanding? Thanks a lot for your answer

What kind of pressure washer are you using? Electric or gas? PSI?

Love your videos! I’ve seen your older pricing videos but was just curious if you could post what your pricing now and your packages. Thanks!

I run a detail business here in South Florida and thank you because I never slow down and just as you said working 12-15 hr days feels great pushing yourself to the max cuz we’re hard working men but dude I hit burn out every month lol we are very similiar.

Do the oxidation video

What do you recommend for rusty bolts and clamps?

How do you price?

About how long will the wool pads (double sided last for you? I have some deep gangway ledges since it is a cuddy cabin/walkaround - and I'm going to try using the side of the wheel since the dewalt is too wide to reach down when held parallel. Regardless - good instructions as always; much appreciated. Stay hydrated in that FL heat.

Great video. you gotta try ditec's glasstec for protection and their crystal clear for cleaning next time. insane results on my glass doors and windshields

Great video, nice!

Have you looked into ppf for marine applications?

Any tips or tools around emblems and rub rail? Is it worth taking the rub rail off?

Maya Angelou quote! Nice!