Super! thanks for the video, I'm just in R52 and this will help me a lot. it's an ot, but can you please tell me more about the mobile phone holder I see in the video? I'm struggling in finding something nice/efficient. thanks
@ggale592Ай бұрын
I know this is a pretty much dated video, but I try. Do you know where is the code line to change from miles in km?
@mertcapkin72632 ай бұрын
Where did you get the inpa profiles for 1st gen?
@joaocustodio13765 ай бұрын
Hi! Do you know what is the line code for automatic front lights ? I have the beam and the sensor but the light are always on.. never turn off even during daytime
@joaocustodio13766 ай бұрын
i am thanks a lot... do you know where is de code for auto ligths? and how to activate
@renzonovara27287 ай бұрын
Thanks for the video! What I’m struggling to figure out, is how to re-program an used BCM, replacing my water damaged original. I can’t seem to find a video that shows the full process with WinKFP to reprogram a replacement (used) BCM (same part number) for the R53/52.
@copacetic_carguy6 ай бұрын
I'd love to know if not I gotta send both bcm's out
@Dev4663t5 ай бұрын
did you ever figure out how? i have a similar situation :(
@spannersautoandcomputerser16493 ай бұрын
You only have to reprogram the keyless entry. The rest will work if similar part number BCM.
@user-qp9zy6zm2z9 ай бұрын
Love the video I emailed to Oder the software. Would want to know if it is a problem when it comes to the installation
@DoDo240319 ай бұрын
Hello! Can you help me in one problem please? I installed a remote engine start and I need to code it to lock the car with key in ingnition (key chip near ignition antenna) I can’t Find the line for coding in BC1… There is Any solution? Thanks a lot!
@britishvaluesforever11 ай бұрын
Hi I can't seem to find the Mini listed in this software. Is there an update
@tomgt007sugden Жыл бұрын
Mate I am struggling to get this software.. tried email the guy, do you have and other contacts. Many thanks 🙏
@airoh11 Жыл бұрын
The software is free from bimmergeeks. Make sure you find the latest sp-daten files.
@tomgt007sugden Жыл бұрын
@@airoh11 you are a legend.. thank you .. 🙏
@tomgt007sugden Жыл бұрын
Can you trigger the abs pump to help bleed the brakes.. many thanks
@britishvaluesforever Жыл бұрын
Does it work with 2005 R52?
@britishvaluesforever Жыл бұрын
Can this software enable original xenons fitted on my mini as they are strobing
@pazoneill8907 Жыл бұрын
there is no option to Activate the OBC how do i do it there was no option on yours either @JCW JAMES
@Headshot1002 Жыл бұрын
Hi, I wonder if you can help, Im trying to add a multifunctional steering wheel from a non button wheel in a 2017 Mini F57, I have Bimmercode and got volume working but thats all HELP!!!
@abdullahkareem6681 Жыл бұрын
Would I be able to enable sport mode to be always on?
@patwong6 Жыл бұрын
What version of INPA, EDIABAS is this? I installed INPA 5.06, both the battery and the Igition dots are black which means the cable is communicating with my R53. I get error message "IFH-000: DATATRANSMISSION TO INTEFACE DISTURBED. Program will be stopped," when I select the Egnine, EMS2K. Also, in main INPA menu, selecting "info" button, the information screen indicates "EDIABAS" Ini path:??????????, Ecu path:????????? and Interface:???????????? What does it mean? Not sure if you are still using INPA, any help would be appreciated!!! I want to reset adapations on my R53. Thanks!
@itsmerewil Жыл бұрын
I dont have SIA Reset f3 option, its blank - Do you have any idea why?
@itsmerewil Жыл бұрын
Can you show, how to connect to KMB and edit belts? :)
@loope96reach Жыл бұрын
Hi! Thanks for the video! Could you link where you downloaded the INPA software please?
@race5050R12 жыл бұрын
Hi we’re did you order the INPA software and cable?
@dogfriendlycoffee4 ай бұрын
i would like to know this also pls
@Indyhalf2 жыл бұрын
I will try it with r50 2001, i want follow home lights and confiot with remote, thanks from Spain
@Jolly-Sid692 жыл бұрын
Hello, does this program fit mini 2005? I decorate
@mertcapkin72632 жыл бұрын
where to download NCS expert?
@scooter13912 жыл бұрын
Hello can you tell me if there's a coding that could be shut off the lock and unlock buttons on the key fob this way? I had to make a new key fob to start and run the car but the buttons don't work no matter what I do. I have a 2010 mini cooper s r56 Can you help direct me what module that would be under to see if it's disabled or enabled,
@scooter13912 жыл бұрын
Found it to be a cheap key fob bought a different fob and key locks work boat ways
@MegaEnriquec2 жыл бұрын
Hi good morning I would like to know if you could help me with my mini cooper I change the ecu and it was for an automatic and mine is stick so computer trying to communicate but is not there so it send a check engine. Can you help with this?
@robertananni42492 жыл бұрын
ciao james, complimenti per i tuoi video , sei bravissimo , ti chiedevo per codificare il corpo farlallato mini cooper s r53 , posso usare NCS EXPERT e come faccio ad identificare il modulo . Grazie se mi puoi aiutare.
@nickjames60132 жыл бұрын
will this work with 2012 r60 for coding multifunction steering wheel?
@v4yne12 жыл бұрын
I've done a remap and pops and bangs tune on mine, is this going to remove the remap?
@r53sam2 жыл бұрын
I hope so.
@v4yne12 жыл бұрын
Well, I wont do it then. Thanks
@TheGrimoar2 жыл бұрын
i cannot connect at all always says chassis is faulty and i dont have that options at all when i click load profile options that i have are default profile and dummy nothing else like you
@airoh112 жыл бұрын
Have a search for the revtor profile ncs expert on Google and install that. Also make sure u have the latest daten files for the R50/R53
@nicebloke60662 жыл бұрын
Hi, great vid! I’m looking to add the twin dials (but without the chrono pack central dials, keeping the big speedo). I understand that it is plug and play but also that to get the warning lights to work properly I was told you need to code it to twin dials - is this an option you can set with ncsexpert?
@geneandrew12692 жыл бұрын
I have an 2007 R56 base non turbo that I replaced the transmission. Would I just need to update the vin# in the code to my vin. Car cranks but won’t start after tranny replacement.
@BlahBleeBlahBlah2 жыл бұрын
Thanks for this, I’m in Australia and in summer I’ve noticed the high speed fan running for a while after turning off the car, especially after stop-start driving. Im going to test mine today. Annoyingly I didn’t think to test this when I had the front end in service mode - is it possible to replace the resistor without going full “service mode”?
@BlahBleeBlahBlah2 жыл бұрын
Quick other question, on “medium” (high) speed both the radiator fan and power steering fan run. However on low speed neither do. Mine’s a 2002 model - I can hear a relay click, so I’m guessing it’s the resistor that’s gone bad. Thanks for the tip!
@airoh112 жыл бұрын
I think you can do it with just removing the top hose and pivot the radiator to gain access to the resistor. If you leave the rad cap on it should reduce the amount of water being emptied out.
@airoh112 жыл бұрын
@@BlahBleeBlahBlah yes that will be the resistor. Check the 5a fuse in the engine compartment fuse box too. I would suspect it will be the resistor. Also remove and give the power steering pump fan a good clean.
@Scott555ish2 жыл бұрын
Can this activate the obc trip computer on an R56 JCW ? Thanks
@TheOZwizzard3 жыл бұрын
I get a message all time vin is faulty
@iansutton54613 жыл бұрын
Hi James .. great video.. it was a lot of help for ncs expert .. just a question or 2 .. my abs pump needed replacement and I did that .. the problem I have now is that the traction control light is permanently on.. my question is .. is it possible to recode the unit to remove or turn of this light and restore the traction control.. can this be done in ncs expert and do a restore to factory in it .. I would appreciate and input or a video even better .. again a great video .. by the way it’s a Mini Cooper R50 01 plate ..
@airoh113 жыл бұрын
Hi Ian. Have you done a fault read? Is it a abs light? As it could be wheel a sensor or do you have a traction control light on? Iv not seen a r50 with traction control before maby this was a optional extra you have? What abs unit did you replace it with as there are normal ABS units for the cooper and w/ASC & wDSC options throughout pre and facelifts models depending on the cars spec. These one found in the cooper s are slightly larger than the r50 abs unit. There is a dsc option in ncs dummy & expert, the module mk60, but Iv never touched any of this. Sorry I can’t be of much help.
@danielvelikov553 жыл бұрын
hello how can i do the american style turn signals for r53s
@airoh113 жыл бұрын
You can do the American style hazard lights with double flash.
@jacobbriggs45923 жыл бұрын
With this could i say, have it ignore my steering wheel airbag since i have an aftermarket wheel and no airbag the light is constantly on. Also i ripped out my steering angle sensor accidentally when adding the wheel could i code that out as well with this
@airoh113 жыл бұрын
Yes you can
@laurenceking20143 жыл бұрын
Do you carry out key fob programming and if so, how much do you charge for mini cooper s 2009
@jonny2legs773 жыл бұрын
This worked for me really chuffed. Only thing I’m struggling with is find which program will just read faults as I bought a laptop with all the stuff of it on eBay it’s very confusing
@airoh113 жыл бұрын
INPA Bmw software will read and clear faults. Some places on Bmw forums can be found for free.
@jonny2legs773 жыл бұрын
@@airoh11 it’s all new to me. I followed your steps and it worked perfect. I will look what’s on it as it’s jam packed full of stuff and hopefully find the correct mini code reader on it
@gskfarmsgh59072 жыл бұрын
@@airoh11 Great job please how can i get in touch with you?
@ReuCollinson3 жыл бұрын
This really helped thank you
@henrykennedy24503 жыл бұрын
How much was the kit
@airoh113 жыл бұрын
The easy way is to get the software from ebay and it can be found fairly cheep at around £20. Then just buy the K-Line (Blue) cable or the K+Dcan cable(Silver). I bought the bmw software kit with cables from bmwdiagnostics on ebay. However you can also find INPA and Ncs Dummy/Expert for free on bmw forums but you will need to also find the daten files for the R50/R53 for it to read that model.
@adamvk82343 жыл бұрын
Hi James. When reading EWS, NCS says the vin is faulty. I do Have the r50 Daten files however i must be missing something? Any help is greatly appreciated. Great Video by the way, keep it up!
@asianR533 жыл бұрын
I fixed it by going to Device and printer, fix the problem with trouble shoot, then go to Device manager>ports>update if possible>right click on the usb port> properties>portsetting>advance>make sure com port is on 1 and latency timer 1> ok and now try again of it works
@joshuacox53723 жыл бұрын
So, is this the same programming system to set up the chrono pack for the R53. Ive already ordered my gauges and heard i have to get them programmed. Pre face-lift model.
@rafsport77023 жыл бұрын
Thanks a lot men. A great tutorial, I’ve followed all your steps and successfully coded my R50. PS: You got yourself a new Sub!
@amritcheema19553 жыл бұрын
thankx alot mant i changed my ABS module just want to code it now could you please tell what ABS module called in NCS expert ?
@user-kh4pm1eo7i3 жыл бұрын
Hey James, thank you very much for your simple explanations, it's very helpful. I want to know how can I activate cruise control after installing an R56 retrofit multifunction steering wheel.
@@airoh11 Hello, how can I contact you for a few questions
@psycho33443 жыл бұрын
Thanks for the info. Can this software or inpa be used to code another ecu to a r53 I have one with a failed ecu and want to use a 2nd hand ecu
@EternalPlatinum4 жыл бұрын
Hi , I’ve got NCS expert running on my pc but the profiles are missing all I have are the default files
@EternalPlatinum4 жыл бұрын
Just got the profiles installed but now i get a “Chassis is faulty” error as soon as I select my car
@kylemanning32073 жыл бұрын
@@EternalPlatinum Did you ever fix this problem? I'm having a very hard time getting the R50 Datens installed.
@tylerduncan86874 жыл бұрын
Hey James, Just want to thank you for posting the vid, its definitely helpful having the simple basic steps to at least get in and have a look. I watched your other vid on clearing adaptations so was happy to see you made a new one! If you have time could you let me know what the basics of the modules are, at least the abbreviations, like BC being body control etc. Thanks again mate excellent vid!