Hi I actually contacted Fronius. They suggested not to use an adapter, because it was quite likely the increased voltage from 110-220 probable melted the components. They suggested I either cut the cable and install a 220 plug or get a new cable. Best regards, Roy
@rbrahen2 күн бұрын
Hi Chris I have a transpocket 180. Got the E 4 error code and it shuts down. Im increasing the shut off voltage from 45 to 70 to start. Im in Europe now and the euro cable does not have a built in ground so I need to use an adapter with a ground also. The adapter is not made well and the ground may not be as secure as I like. Im wondering if that could be a problem too. Your thoughts, thank you. Roy
@bigkight8 күн бұрын
how did you secure it to the existing base?
@MalkanaImpex18 күн бұрын
Sir, we can make this welding glove for you?
@sgr528728 күн бұрын
Someone have problems with the lift arc? Most time the tungsten sticks and damages it
@chris_b_liven27 күн бұрын
Hello, on the TransTig 210?
@sgr528727 күн бұрын
@@chris_b_liven transtig 170
@jorgefere9314Ай бұрын
Puede soldar aluminio con proceso TIG?
@engjdsАй бұрын
Question, when you set a material thickness, then change the voltage, on my machine it re-adjusts the material thickness, but you change both, does it do it independantly, and how do you do that?
@chris_b_livenАй бұрын
Yes, you can turn on a setting in the background called ALC - When it’s turned on you can set material thickness/wirefeed separate of voltage
@engjdsАй бұрын
Can you do spray transfer on steel on a TS2200? if so, how?
@chris_b_livenАй бұрын
Yes, you can with .030 and .035 solid wire. All you need to do is increase the voltage vs wirefeed speed
@engjdsАй бұрын
@@chris_b_liven So 0.8mm wire size, metric Chris?
@engjdsАй бұрын
Got the TS2000, questions: 1) Why is there no Synergic mode for 0.8mm flux core? 2) Why does Aluminium start at 1mm, and if you have 0.8mm wire, can you still use it?
@engjds2 ай бұрын
Does the transteel 2200 take tig torch take standard cups?
@chris_b_liven2 ай бұрын
Yes, if you buy a new TIG complete it takes standard thread on consumables. The back caps are Fronius.
@engjds11 күн бұрын
@@chris_b_liven Thanks Chris, also what tungstons do I need to buy for Steel and Aluminium, look to be about 3mm?
@engjds2 ай бұрын
Great stuff, but can you run 6010 or 6011 rods on it? can it weld very thin steel and mig thin aluminium, I am one step away from getting one, but also have my eye on the Artis 170.
@chris_b_liven2 ай бұрын
Hello 👋 It doesn’t run 6010 or 6011 but it runs 6013. We are running a promotion on the TST 2200/2700. Shoot me an email for more info [email protected]
@engjds2 ай бұрын
@@chris_b_liven Hi, Chris, will do, the open circuit voltage suggests it should handle cellulose rods, but not even 6011( even the cheap amazon ones can do that.
@engjds2 ай бұрын
@@chris_b_liven The TS200 has an open circuit voltage of 90V, so on paper it SHOULD run any rod, online one guy said he talked to a tech guy at Fronius that said it will run any rod including the 6010, so question is, have you tried running 6010 or is it just based on a possibly false rumour?
@engjds2 ай бұрын
@@chris_b_liven Also, I think it has a feature to prevent long arcing? maybe people are not disabling that before trying 6010 and then thinking it cant weld it?
@engjds2 ай бұрын
No one seems to test stick on the 2200, but there are situations you would use stick, like 6010 on unprepared materials.
@THEREALBIGGHEN2 ай бұрын
Bro sell me the business
@honghuoxiu2 ай бұрын
希望能有中文字幕,謝謝分享
@JMCmotion2 ай бұрын
What a great video! If you need to mount another one, take a look at "The New Guy Robot Mount" from JMC Motion. It's made to work with your existing fixtures/tooling and reduce upfront costs.
@dylpickles73412 ай бұрын
Hey im running like 25amps 8-10 hot start -4-(-2)dig and 30-35 gass doing ok but i want a smoother weld puddle any advice? Btw the thickness is anything from 3/8 to 3/4
@victormlara212 ай бұрын
Is this unit able to do CuSi3 and AlSi with pulse mode?
@chris_b_liven2 ай бұрын
Hello 👋 no pulse mode function but it welds great in standard synergic mode
@lestjepan3 ай бұрын
My turn 😊
@lestjepan3 ай бұрын
Well done bro
@TheCatoLee3 ай бұрын
I weld copper cable leads wich has to pass x-rays. I use Lazer Helium gas and DC on the torch. Works like a charm.
@volodymyr9613 ай бұрын
Hi, what would you advise for truck repair? Transsteel 2700 will be enough on thick metal or 3500 maybe?(2700 has one phase,that’s cool)
@chris_b_liven3 ай бұрын
Hey. The 2700 should be a big enough machine for truck repair. What is the maximum wire size you will use? There is a promotion running where you receive a free secondary MIG lead with purchase. Shoot me an email and I can help with directing you to the closest dealer - [email protected]
@danielbottner77004 ай бұрын
E308LFC Flux core wire voltage range recommended is 24 to 31 volts. Wondering why you chose 16 volts ?
@BrandonLund5 ай бұрын
I love my 210. Buttery smooth. I used it this week (stick mode) fixing a dump trailer that rolled over. You do a great job explaining the features.
@rfluck5 ай бұрын
Wish they didn’t just abandon their product and business cause here I am looking for something like it
@BRENT31439455 ай бұрын
Ive used my 2200 with 250ft of cord . welded on alot of docks with it.
@sibosifraiscompagny6 ай бұрын
When they will make the transteel 2200 with pulse?
@sibosifraiscompagny6 ай бұрын
Do you know if fronius will came with a TPS2200 soon or a mig that do 110 and 220 with pulse or a transteel2200 with pulse!
@Xtremepoophead6 ай бұрын
This is the greatest video I’ve seen on this challenge honestly. Great work!!!
@TheMetalButcher6 ай бұрын
So it is kinda gimped on single phase...?
@chris_b_liven6 ай бұрын
Yes, a little . Not a full 270 on single phase
@KZ-yy9pm6 ай бұрын
I can't believe I'm just finding alum vids with the transsteel now, I've watched so many vids of htp and everlast (trying not to go spoolgun for my miller) and was convinced welding alum with a normal gun was a gimmick. All these pulse and double pulse machine produce the worst results. I need a Fronius.
@chris_b_liven6 ай бұрын
It welds amazing on aluminum!!!! For a 110/220v unit - Promo QTR 1 2024
@KZ-yy9pm6 ай бұрын
@@chris_b_liven so there’s a promo if you purchase in 1st quarter of 2024? Where can I get more info?
Im gonna do a 1" 3G / 4G weld test soon, 0.45 flux wire 100% Co2 , ive never done this with this gas mix. Ive always done C25...any advice guys??? Id really appreciate it...thanks before hand !!!
@Ok-uc5in7 ай бұрын
I got to get up at 2 for my workouts
@bearkawiboy62467 ай бұрын
Fronius direly needs a 250amp+ Multiprocess Welder with A/C Tig capabilities for aluminum, HF start and one that is a 120-240v single (1) phase machine!! The competition is there. Something the beats the HTP 2500, ESAB 205 285, Miller 220 and 255 multimatics, Lincoln 215 etc
@JohnSmith-ho8up7 ай бұрын
Hi. Slowly learning the settings on this machine and your videos have been absolutely priceless.. Many thanks.. What's your thoughts on 2200 as a tig machine. ? My local distributor doesn't rate it for anything other than small repairs
@chris_b_liven7 ай бұрын
For a lift arc DC tig machine it’s pretty unbelievable
@engjdsАй бұрын
@@chris_b_liven Why do people need HF start over lift arc?
@WorkingK9Cook8 ай бұрын
How much has this costs and how long so far. We are wanting to do this coop
@chris_b_liven7 ай бұрын
It was about $600
@rsanchez56768 ай бұрын
Would you know what type of aluminum is at Lowe’s or Home Depot for their aluminum stock of flat angle etc ?
@joeyjohnston998 ай бұрын
can't hear you
@JoseAGonzalesDelgado-fh5lq8 ай бұрын
Greyt
@user-vm6mv8il6s8 ай бұрын
silicon bronze tig is the way to go ..
@danilc56778 ай бұрын
Great intro to the 2700! Thanks
@rojametallbaumanufaktur29068 ай бұрын
Very good review.... Thanks
@larryclark93808 ай бұрын
Help! Is this DCEN or DCEP??
@chris_b_liven8 ай бұрын
Electrode +
@jesusmendoza70709 ай бұрын
Sounds good! I’ll like to watch the video!!
@jdeluisa9 ай бұрын
Hey man, hope you are well. why can't you use a foot pedal with the transsteel 2200?
@JohnSmith-ho8up9 ай бұрын
Can you use the battery on a 240v Transteel 2200?
@chris_b_liven9 ай бұрын
No.. The AP 150 doesn’t offer a port for external power
@thgautomation9 ай бұрын
We did some cool stuff that week. I love the videos!
@kevinshiell87739 ай бұрын
Hi Chris, First of love your work . Why is that when I mig weld in manual flip up my hood after running a bead & sometimes my settings change ? Any help would be great
@StatuaryGrape9 ай бұрын
Got a used accupocket and couldn't figure this out for the life of me. All good now. Thanks!