O'Henrys Services Jeep

Пікірлер

@ohenrysservicesjeep233 3 күн бұрын

It has been a fun distraction for summer ❤

@Oversizeddoneright 3 күн бұрын

Looks like is was a bit cold for the captain.....what is top speed?

@ohenrysservicesjeep233 3 күн бұрын

33mph according to the phone...it was 55 degrees but quickly rose to 90 degrees by the time we left..

@4mula353 12 сағат бұрын

You can install a set of bow bunks in place of that center roller. That will help keep the bow in line provided the trailer isn't too deep in the water

@Oversizeddoneright 5 күн бұрын

Looks like it will keep the sun off and the guide will help loading the boat❤❤ good job

@ohenrysservicesjeep233 3 күн бұрын

Yes it will

@Oversizeddoneright 11 күн бұрын

Definitely looks to have more clearance

@ohenrysservicesjeep233 3 күн бұрын

Following Final test...remodeling stop helping ❤

@ohenrysservicesjeep233 11 күн бұрын

It was an enjoyable test!

@Oversizeddoneright 12 күн бұрын

Sounds good

@ohenrysservicesjeep233 11 күн бұрын

It was an amazing time

@Oversizeddoneright 12 күн бұрын

Looks like a blast!

@Oversizeddoneright 19 күн бұрын

Glad the boat made it to the trailer 😂

@DannyWeaver-pd9jm 19 күн бұрын

Ialmostdied😮

@mustrook1 19 күн бұрын

Is the water pickup theoufh rhe hull? My project boar has a motor mounted water pump and it comes through the hull. Something to look at.

@Oversizeddoneright 12 күн бұрын

Updated video shows the problem was the rubber hose between heat exchanger and outdrive!

@ohenrysservicesjeep233 11 күн бұрын

There were a few problems with the boat when I got it one was the rubber hose connecting the exhaust was not properly installed and was causing a pretty massive leak.. I was basically pumping water into the boat ... the second problem was the 4 lower bolts on the outdrive were fairly loose and was causing leakage.. The third problem was no ceiling at the bottom end of the transom and outdrive.... Last video I posted at the time of this response was following a 3 hour lake test that went very well....

@ohenrysservicesjeep233 11 күн бұрын

The answer would be ...water pickup is in the outdrive near bottom....bigger issue were outdrive bolts loose and rubber hose connecting outdrive to heat exchanger was not installed properly..

@Oversizeddoneright 24 күн бұрын

Measure a billion Time cut once......wise words😂

@Oversizeddoneright 26 күн бұрын

How did the support under the dash turn out? Was it broken? ❤❤boat looks good

@ohenrysservicesjeep233 25 күн бұрын

It must have been an optical illusion....100 percent solid!

@Oversizeddoneright 27 күн бұрын

Boat looks good....hope it's solid

@Javiertapiavzla84 Ай бұрын

Buen vehículo... saludos desde Venezuela. Quiero restaurar uno igual. Saludos.

@ohenrysservicesjeep233 11 күн бұрын

Thanks for the kind words

@Oversizeddoneright Ай бұрын

I like the fab skills ❤

@DannyWeaver-pd9jm Ай бұрын

Let me get dat seat😮

@Oversizeddoneright Ай бұрын

That after pic looks tuff!

@Oversizeddoneright Ай бұрын

Vendors don't have the quality control that they should 😢 but you will get it sorted 😊

@AnnalisaWeaver-hg4jr Ай бұрын

Really nice work....

@justingross2167 Ай бұрын

Those holes your talking about welding up is where the shovel head bracket welds on, you will also need to re drill the holes for the footman loops that hold the straps for the shovel handle. You can buy the corner radius's you need from Cameron manufacturing, they make all the panels you need.

@ohenrysservicesjeep233 Ай бұрын

Thanks, I wish I could find a diagram of where axe holder footman loop and shovel mounts belong. I already finished the front corner radius section came out nice. Thanks for the info

@Oversizeddoneright Ай бұрын

The weekly updates show alot of progress ❤❤ wonderful work

@ferngilliland9113 Ай бұрын

One of the best videos I’ve seen How will it all end up smooth?

@Oversizeddoneright 2 ай бұрын

Thats going to be finished in no time❤😂

@ohenrysservicesjeep233 2 ай бұрын

Thanks

@Oversizeddoneright 2 ай бұрын

The original bumper support and cross member connecting to the receiver hitch will make an awesome and strong connection point. The completed project looks awesome

@Oversizeddoneright 2 ай бұрын

Looks like a fairly simple build! Can't wait for the finish!

@Oversizeddoneright 2 ай бұрын

Nice work on that.. very secure mounting for sure.

@milcommguy5927 2 ай бұрын

Good job

@ohenrysservicesjeep233 2 ай бұрын

Thanks...

@Oversizeddoneright 2 ай бұрын

That dog wants in! But looks like a big furry ball