Ай бұрын
Ай бұрын
2 ай бұрын
6 ай бұрын
7 ай бұрын
7 ай бұрын
11 ай бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Пікірлер
@rlittleatiiacom Ай бұрын
Acieta does such a fanatic job of communicating with customers.
@justtisha 3 ай бұрын
How did the programmer keep singularity from causing a big issue? I see that forearm whipping around.
@ndleonard 2 ай бұрын
It is possible to use joint movements to avoid singularity. I often have to do so to get tooling onto a position I need it to be in.
@studio402_films 7 ай бұрын
Great video
@deshmukhvp 8 ай бұрын
Hi Chris, can we get the list of greases and oils used for the lubrication of Robotic systems ?
@sezerakcakaya 8 ай бұрын
Arc welding is not in good position. You should be using a positiner while welding.
@williamlogan1775 3 ай бұрын
CJP is CJP no matter what angle your torch is at. Only issue you might have pulling away like that an that angle is shielding gas but if thats all its welding it wont be an issue.
@arko94 10 ай бұрын
wtf is that config on bending robot, why second axis is going below like that, could you ceep the same range on third axis throu out whole proces? was there problems on 5th axis if robot would have more common configs?
@DVent_Zf-1 Жыл бұрын
Hi Chris, have you found a simple/fast way to fill the J5/J6 oil on the M20ia?
@guptaji_k7 Жыл бұрын
Can we do all axis greasing simultaneously by any process?
@stuartshepherd3281 Жыл бұрын
Congratulation of 40 successful years! Nice video, too!
@rlittleatiiacom Жыл бұрын
Congratulations!
@sergiomadrona4144 Жыл бұрын
Hello Cris, It is posible to replace the CPU batterie with the robot turned ON?
@luigi1296 9 ай бұрын
Yes, you must change the cpu batteries when the robot it’s turned on, in the same way you change the batteries of mechanical unit.
@dai3995 Жыл бұрын
666
@889976889 Жыл бұрын
More job loss
@vickfs2514 Жыл бұрын
excellent explanation, could you please make a video on how to load and unload a template of rows and columns with the palletize function? thank you very much for sharing your knowledge
@williamhuang5329 Жыл бұрын
Hanzhen harmonic drive gear , strain wave reducer, robot joint , over 30 years experience
@williamhuang5329 Жыл бұрын
Hanzhen harmonic drive gear , strain wave reducer, robot joint , over 30 years experience
@antonmursid3505 Жыл бұрын
Antonmursid🙏🙏🙏🙏💝✌🙌👌👋🇮🇩🇮🇩🇮🇩🇮🇩🇮🇩💝✌🙌👌👋
@enzolee9528 Жыл бұрын
good on every welding start make TPS again . good engineer
@prestonwarren2692 Жыл бұрын
Love fanuc robots.
@viktordluhos1817 Жыл бұрын
Great job! Looks awesome!
@antonmursid3505 Жыл бұрын
Antonmursid🙏🙏🙏🙏🙏💝✌🙌👌🇮🇩🇮🇩🇮🇩🇮🇩🇮🇩💝✌🙌👌👋
@xiaozhong622 Жыл бұрын
Good Job
@williamhuang5329 Жыл бұрын
Hanzhen harmonic drive gear , strain wave gear , robot gear joint, over 30 years experience
@williamhuang5329 Жыл бұрын
Hanzhen harmonic drive gear , strain wave gear , robot joint , over 30 years experience
@jimsvideos7201 2 жыл бұрын
Probing with the weld wire is pretty clever.
@tylervxxx9256 Жыл бұрын
Looks like touch sense. It's pretty handy
@benargee 11 ай бұрын
Yes especially how it trims and probes a known datum to account for error in the wire.
@williamhuang5329 2 жыл бұрын
Hanzhen harmonic drive gear ,robot joint , strain wave reducer, over 30 years experience ,
@williamhuang5329 2 жыл бұрын
Hanzhen harmonic drive gear , robot joint , strain wave gear , over 30 years experience
@samuelsavage6396 2 жыл бұрын
Is the back gauge on the press brake needed in this set up, what’s the accuracy of the robot vs the back gauge?
@AutomationWizardry Жыл бұрын
It is needed. The robot is pretty accurate, but you can’t accurately bend a piece of metal that bends and warps. The robot can’t compensate that, so you need back gauges to get rid of the inherit uncertainties of the part. Hope that helps
@dhirenparikh6798 2 жыл бұрын
Good tech👍
@williamhuang5329 2 жыл бұрын
Hanzhewn harmonic drive gear ,robot gear reducer, over 30 years experience
@williamhuang5329 2 жыл бұрын
Hanzhen harmonic drive gear , automation joint gear , robot gear , over 30 years experience
@williamhuang5329 2 жыл бұрын
Hanzhen harmonic drive gear , automation joint gear , robot gear , over 30 years experience