I would not recommend using an eraser wheel for removing pin stripes or decals on trucks, some people have great luck, but it’s luck of the draw, I bought a 3 mm eraser wheel off Amazon, I used it for removing a pin stripe, well the second it touched my truck, the eraser is almost as if it melted and stuck to my truck like tar, but worse, I’ve tried everything trying to get the eraser wheel residue off and the pin stripe off, here it is a week later and still can’t get it wiped clean and cleared up, I’ve tried everything, goo gone, residue remover, alcohol, buffing, hand sanitizer, I’m going to try a heavy duty clay bar next, but I feel it’s a waste of more money, those eraser wheels can have a bad outcome, be careful using them, it wasn’t as simple as people made it seem, and I was going at low speed, I had barely touched the truck, so I know I didn’t burn it or anything else.

I always wondered if this would swirl your paint. Clean the area well first I guess.

Thank you for this!

Tbis helped !!!! Thank you so much

Theres a bad fuse if i had to guess its the radio

Brilliant video! Thank you for taking the time to post this. I probably avoided 30 minutes of headaches watching this!

when I order my brakes for my grand Cherokee, I also noticed they asked for the millimeters 330 or 350 MM

You should have brought a Power Wagon !!!

Im in the middle of my build on my 24 Ram 2500 Cummins so definitely appreciate the walk through! nice work. Lots for me to think about once my topper comes in, hopefully this week.

Ive had pulling to the right problems since installing Thuren a couple years ago. I went by their specs to align and went a little more and less to see if it changed any. I’ve been to several shops to see if they can help. I finally called Carli to see about changing to a different system. Super nice guys and they stated it’s common with these trucks but they have a stabilizer that uses pressure to counter the pulling that works with their kit. So as soon as I get a chance I’ll be getting this Thuren stuff off and going a different route.

Definitely not normal

Is the longer handle uncomfortable in a wading belt?

The weird trick I’ve always done is sit in front of the wheel real close with my legs spread open and u put both my feet under each side of the tire and I pick up with both my feet (heels on the ground) and my arms at he same time and guide it on lol

Mine didn’t come with the castle nut. Only the bolt, and it’s brand new. It’s not even listed on the parts list diagram. I’m buying a Festool. Their tools come functioning out of the box without fussy phantom parts.

People are stuck in the old days with 3, 4, and 5 speed transmissions with 31 inch tires. They automatically think it will kill fuel mileage. When you have a diesel with 800 to 1000 ft pounds of tq yes you can go higher gear. But with a gas you have to put more gear to compensate the lower tq. I ordered 4.30s in my 7.3 gas with a 10 speed. I am 2000 rpms at 70 mph with 34 inch tires. It does great and really pulls hard for a gasser.

Where do you get your tread ?

Wow the price has gone way up on these for sure wow😮

I’m doing a 2nd gen Ram but I doubt I will go as far as you on your build , great looking rig 👍

Ram looks great bud nice work!!

Thank you man

Dream build right there! Awesome to see it complete

Chinese finger trap

ended up going with a progress hybrid soapstone. Hopefully offset the cost of propane usage for the whole house in a few years. Have a great hookup for cheap dry hardwood (amish wood working supplier) the wood is cut into small logs and moveable sizes. Super excited for it to be done! looked at pellet stoves, but the thought of lifting pellets upstairs to heat the room (bi level home) didnt seem to fun. The wood stove will be in the basement next to a intake register for the furnae to help move heat. Great video and points to consider!

Just finishing installing Aria railing on a small deck. The only issue was snapping the top covers on. The ratcheting clamps are the only way to snap the top covers on! I recommend the strong 835 pound clamps.

I think the oil capacity on the 2.5 liter is actually 4.4 quarts with a filter change

Thanks so much for posting this. Yesterday was my first time using a new SpinRX and a brand new, longer anchor rope. I use my drift boat on rivers and lakes, yesterday I was on a lake, and after dropping the anchor only 3-4 times in up to 12' of water the system became completely unusable due to rope twist. Today I added a close variant of your system. Less than $10 and 15 minutes of time. Thanks again.

very fine, thankyou.. John Atherton describes some spider/skaters with size 16 hooks and up to 2 1/2 inch diameter hackles... I would love to see you try one.. if any one can you can.. :D Again, thanks.

I agree

Don’t you think you should have doubled up the ledger board ?

Your tha truth man!!!!!!💯💯

how deep the holes ???

how did you determine the height cut of the 4 by 12 support post

was there a measurement from string up to the cut

whats the purpose of cutting above the string

I found the caramel wheel a brilliant product to remove 20 year old sticks down either side of my station wagon.

Still nothing I have been fighting it for 4 days now

I used a plastic razor blade on mine and it worked great

Just bought CJC 17” Method wheels and 37 Toyo Open Country Trail. Don’t like the caps. My hubs look little rusted with surface rust. Nothing crazy cause the truck came from Ft Lauderdale Florida. Going to try to sand them down and spray them. Im moving to Michigan this fall. Need to figure out how to protect the truck from salt and rust. Thanks for your video.

Heat is essentially the worst enemy. I was thinking about using thermally conductive epoxy and heatsinks where it makes sense.

This would be a fun vehicle to take to the river. I wonder if some of the electrical/grounds are corroded, given the rust and the slow crank.

The poor guy selling tires to this dude…😂

Man I don't like that you're saying this jeep is 30 years old.... it's just not right

I just saved like 500 bucks… 295/65/20 vs 35/12.5/20… The metric is only 1” narrower and actually 1/2 bigger.. and with the load rating I needed to go up in ply So in order to get a 80 lb tire it needed to be a F with the 35. This guy just saved me a lot of money.

Pro tip for the oil filter, flip the truck vertically, problem solved ;)

Mag wheel cleaner helps clean aluminum. Wont do jack shit for heavy corrosion..napa aluminum brightener works too but the eagle one mag wheel is better..but obviously wear ppe as both are acid based. Currently cleaning and painting my 4l60.

"what are the chances of that?" I'd say about a 100% chace...

SpinRX (Zigco) actually makes a couple solutions for this, although they aren't as cheap as the swivel snap hook you show. Look for the "SpinRX Anchor arm swivel" or they also have just a swivel that is similar to their swivel pulley but without the pulley and hinge.

I had the 2016 Laramie 1500 and it had the dual front buckets with the center console. I now have the 2019 Bighorn Cummins. It has the bench seat. I like the bench seat . When I back my RV in at home, I like to have the left side close to the wall. I can pop up the arm rest and easily slide over to the right side or vis a versa. The fixed console in the 2016 made it very difficult.

Just got mine 2024 tradesman 2500 with 750 miles for $46999 in Lawrenceville Ga I love this truck

Excellent breakdown!