did you sort it out

I too would love to know...

anything?

@@TheJanope13 No luck for me yet cracking the three digit code. I'm looking at buying the the 5 button controller with the white plug and the 4 digit code, (1688) and hoping it works with my heater. I tried the blue controller from another heater I have and no dice either.

Thank you for choosing LIKACI! Does your diesel heater display any error codes? If there are no errors in the heater, it may be related to the temperature you set. You can try increasing the temperature or setting your gear higher.

Thank you for choosing LIKACI! When you use temperature mode, the heater will run on its own according to the temperature you set, and you do not need to perform any other operations.

Thank you for choosing LIKACI! The 6-button controller we currently use has simplified the complexity of operation compared to most 5-button versions, and there is basically no difference in functionality.

Thank you for choosing LIKACI! You don't need to make any adjustments, just connect to a 12V or 24V power supply, and the heater will start on its own.

Deep cycle marine battery with solar and or plug in trickle charger is ideal but 120 volt ac to 12 volt dc 15 amp power supply will work watch power outage and fire issues due to improper cooldown. Basically watch that thing and don't leave unattended. Have good smoke and carbon monoxide detectors in area

I would like to know this too.

Thank you for choosing LIKACI! Our diesel heater controller can only display Celsius degrees and cannot be adjusted to Fahrenheit degrees temporarily.

Thank you for choosing LIKACI! You can adjust the amount of fuel pumped by the fuel pump each time on the switch of our diesel heater (16 μ L and 32 μ L) However, the frequency of the fuel pump will not be adjusted. This mode does not require matching with the fuel pump you are using.

@@Likaci-Heater Thank you :)

Thank you for choosing LIKACI! Our diesel heater is not equipped with a plateau module, so it is not possible to adjust the altitude on the controller.

same for me

Mam ten sam problem, zna ktoś rozwiązanie ?

I upgraded just can't get it sarted

Disconnect from battery, wait 30 sec. Re connect. Long press the fuel button until prime starts. Might take 5-8 sec. Once you feel it's primed push the off button. Then turn back on. Best of luck.

@@SurreyUs Will try it this way next time I need to prime.

I have the same controller. The prime button doesn't work after you connected the power supply, ie like pressing the prime button after pressing the on/off button on the lower right. Like SurreyUs says, need to press the prime button during the 12v power supply connection (cold boot startup process), then power off button, then power up (warm boot startup). It's not explained well in the manual. When my heater was started from new, I couldn't figure how to prime, but it started after a few minutes as the pump keeps ticking and eventually fuel gets to the heater.

@@Peter-un8no So on mine the above solution worked. Hold button down, plug in display. Hold until pumping starts. Takes a while, maybe 15 seconds.

Thank you for choosing LIKACI! Our diesel heater does not have high altitude mode, so you cannot adjust the altitude on the controller.

@@Likaci-Heater This means that altitude sickness does not affect you, the machine is ready to work well in those circumstances.

Thank you for choosing LIKACI! The main board and controller of the diesel heater need to be compatible with each other. We will ensure that our main board and control are compatible. If you need to install our controller on other heaters, we cannot guarantee whether it will be compatible.

Hi, I replaced the original control of my vevor 2KW with this one and everything works perfectly well, including the altitude display and the function to stop and start the heating completely automatically.

@@-Ckyoso- Thank you very much!!! ;)

@@-Ckyoso- where did you buy the controler ? did you need matching motherboard?

@@-Ckyoso-how did you set to stop and start automatically? Thanks

Thank you for choosing LIKACI! Please send your question to our email address; [email protected] Please provide detailed information as much as possible, and we will contact our engineers to resolve your issue as soon as possible.

Thank you for choosing LIKACI! The existing diesel heaters do not have an fuel level indicator. If you want to observe the remaining fuel in the tank, you need to observe it through the fuel level hole in the casing.

hold the pump button down and it resets it @imthekingofrs2

Thank you for choosing LIKACI! Our diesel heater can only display Celsius degrees temporarily.

We apologize for the problem you have encountered. You can directly contact our customer service team via email at: [email protected] We appreciate your support for LIKACI and apologize for any inconvenience this may have caused you. We will reply to your email as soon as possible and work hard to resolve the issue.

Thank you for choosing LIKACI! You can check out our latest video, it may solve your problem! Link: kzfaq.info/get/bejne/n9B7l6iosbqbg2w.html

Thank you for choosing LIKACI! We have uploaded our user manual, which you can download from our official website homepage or Amazon's product page.

@@Likaci-Heater Thanks a lot for your professional response !awesome!👍👍

You can't. There is no altitude mode on this model.

Thank you very much for your support and trust in LIKACI! We are honored to have you as our customer. If you have any other questions, please don't hesitate to reach out to us anytime. Have a wonderful day!

Thank you for choosing LIKACI! Our diesel heater is suitable for both 12V and 24V voltages. We believe the issue you're experiencing may be due to the voltage exceeding the compatibility of our product. We recommend adjusting the output voltage of the device powering the diesel heater and then checking if the problem is resolved. If you have any other questions, please don't hesitate to reach out to us anytime. Have a great day!

@@Likaci-Heater I would love to test one of your heaters in New England during this cold winter for my KZfaq channel!

Thank you for watching our channel! All temperature related settings of the diesel heater are limited to the output temperature setting of the machine itself, and cannot detect the ambient temperature to achieve machine startup and shutdown. If you have any other questions, please feel free to contact us at any time! Have a nice day!

Welcome to watch our channel You can switch between level mode and temperature mode by long pressing the SETTING key . If you have any other questions, please feel free to contact us at any time! Have a nice day!