Do we apply DC for power factor correction?

Where you get these text boxes?

If for some reason i lost my youtube account, and made a new one you would be the first channel i would subscribe to again, i really appreciate you sharing your knowledge sir!

In tia portal v17 .fwf file not find in the folder of said address Kindly suggest

Hands down one of the best explanations of time delay relays I've ever seen.

What is screwing me up is the #5 wire, shouldn't it go to something separate that closes the holding contact? I think I just figured it out lol. Ok so when the coil is energized it closes not only L1 L2 L3, but also the holding contact?

Thank you very much for the explanation, very helpful 🙏

please can anyone send me this plc ladder logic to my email?

can you give sample with open delta loads with different resistance load?

I❤️you. ☺️thank you!

thanks

GUYS PLEASE TELL ME HOW I SHOW THE CONTING OM HMI, I have a counter on twido suite and need to show the counting on hmi

thank you for the Tutorial

The dogs bollocks in electrical theory

Thanks i am a Sophomore of Electrical power engineer I try so much I want to be an engineer Thank you so much 🎉🎉

You just save me thank you sir

The way he explained it the wiring in the video for the high voltage is wrong then you should probably relay that to everyone so they don't get confused other than that really good video

Thanks Pete, for nice explanation

man ur video series is so crazy good

👍👍

Sir i have a golf vehicle when i press pedal single time it can not move so i press pedal many time then it move and the smoothely run but the only problem is that its starting torque is very low because batteries are fully charged i check input voltage of motor 48 volt dc exact i want to increase motor starting torque what you suggest please reply its humble request

I'm a residential electrician which is nothing compared to this and slowly I started accepting my truth at class that PLC requires more brain than what I have but you're videos are giving me hope, you're way of explaining is making sense to me finally, TY! 2 months away from graduating

230V/400V is better...😉😆

your tutorial is useful but i needed idea on how to set up the usb 4750 using driver , i have downloaded and installed the driver and SDK of DAQNavi , but the driver is not being recognized by device manager , pls help

thank you

I have a small motor like this but its not wired this way where the windings have a long jump line. The two windings are connected together but kept separate by the brush and armature. I think its way less confusing to be wired that way since the way its wired on the diagram is the way its wired irl. Whereas in the vid that jumper wire can cause some confusion.

So if we change the number of windings could we change the voltage ratio from sqrt(3) to 1? If so could the windings of each transformer pair be different and each have their own ratios?

Can you add 2 more lights in rung #2 and have them flash with flashing light 1?

Hey can you do a detailed video of wiring up a three phase reversing like you had in the wiring schematic with the large black motor control you showed in this video @11:40? This is what i have to do for my test at work.

This video connected the dots for me, literally! Taking it from ladder to schematic was awesome. Thank you very much.

Best explanation. Wish you best of luck.

Many thanks 🎉😢❤😊 4:53

Many thanks 🎉😢❤😊

Awesome information. Thanks

A partir de que versión se puede editar, yo tengo la 30 y no me deja

Very good I will try it in my SLC micro logic1000

Great video, well explained, no unnecessary waffle 👍🏿

Thank you , that was very helpful 🙏

I was impressed by your excellent demonstration and equipment. Can you tell me how a three terminal reversible motor is wired internally? I have worked out a schematic for a four terminal motor, but cannot find anything or devise anything for a three terminal reversible series wound DC motor. Thanks for the information!

Thank you for the excellent demonstration! I would appreciate it if you could illustrate the process of transitioning from induction to synchronous motor with an incremental increase in speed up to the synchronous speed. Additionally, if you could demonstrate the transition to a capacitive load motor with a fixed speed at synchronous speed through excitation, it would help me better understand the behavior in speed.

thanks

Excellent explanation

This video help me with my research about DC motors , thank you

this helped me understand the wiring of a six wire 240 volt motor and how to reverse it, i just wasn't understanding the wiring and you made it seem easy

You deserve an award sir! 🥇 You just saved a soul! 😂

If I understood correctly in the ladder language, a load can be activated regardless of whether we have an open or closed circuit in the switch. There is no electrical continuity but logic. And my main question, does ladder language consider all switches as double throw?

oh i am a student, i do not enough money to buy this licience so can you give me this product key and serial number to install it please

Very good video on xic vs xio. Concept always confused me. After this tutorial, not anymore! Thank you!

Thank you so much for making this video! Very well done and answered a lot of questions I had! Great work!