I have this but there is a small black metal piece that when I took off front of shoot I think lifted the flap. Do I need to put back on to use or is grass flap laying on top of shoot tube good enough. Thx

Great job, thank you!

What are the differences between the T300 and the T300 Plus models?

Use the proper jigsaw blade.

I had the same set installed at a local shop and it looks like they tightened them while the truck was in the air because they're angled down and the truck rides very rough. Would this cause the rough ride?

Awesome video. Thank you

Oh my amazing could be easy for you, but I’m sure not for senior to put that together you have a lot of talent and wisdom bet you can’t use it much with the winter coming soon? 😮😊lol good job

this was amazing sir, thank you. The other videos are pretty much guys reading the instructions in front of you and doing it which isn't helpful. You are the man, sir.

I just purchased one from Amazon and it does everything demonstrated in the video, it's awesome!

What is the wood piece used for? Is this necessary to use for the floor jack or can you use the floor jack as is and then place your jack stand on pinch weld? Additionally could you place to jack stands side by side on the same side for extra stability/peace of mind or is there not enough room?

I’m thinking about getting a filter relocation kit for mine. With those factory holes on the frame it gives you a good place to mount them.

Thanks for the excellent instruction for replacing the UCA. I purchased Mammoth replacements and the instructions didn’t say anything about the spacers. This video cleared that up for me when the employees at the store that I bought them from couldn’t.

I’m so glad I found this video. I almost ordered this bagger from the dealership where I purchased my mower & planned to pay them to install! I’m elderly & thought installation would be above my skill level. I’m not afraid to try it after watching the video. I also know now the bags won’t be difficult to get out! Thank you.

A buddy of mine showed me this a few years back. I didn’t own a truck back then, so I figured I’d make one for my current truck. Good idea to use cardboard to match the curvature 👍🏾. I’m gonna wrap mine in speaker box carpet and add a couple small d-rings to be able to bungiecord stuff as well.

To slow would be there for hours

Awesome, no-nonesense video! Thank you for sharing your time and expertise!

11:30 Thanks for the video. It is more help than I’ve seen yet. My question is would it be the same wired set up for a guard dog censor.

Really

Single clearest instructional video I’ve ever watched.

How much is the typical cost of a job like that in a mechanic shop?

My factory oil filter was on there at 1000ft lb also

Thanks a ton brother, going to replace my ancient 007-F3 straight from stone age to the future with a 007e-f2; this write up was exactly the detail I needed to be confident I can pull this job off. You make it seem like a piece of cake. Thanks!

Easy Peezy, my faucet, no leaky. Thank you.

Very Vert helpful!!!! Thank you for doing.

Thank you.

Much Appreciated, thanks to your video, I made one!! All in about $83.... Parts list everything from Lowes: (1) 3/4-in x 72-in Galvanized Pipe, (1) 3/4-in x 2-in Galvanized Nipple, (1) 3/4-in Galvanized Coupling, (2) 3/4-in Galvanized Caps, (2) 1/4-in 2-in Thread Eye Bolts, (4) 1/4-in Flat Washers, (2) 1/4-in x 20 Nylon Insert Nuts, (2) 5/16-in x 2-3/8-in Interlocking Spring Snap ins/ D Rings (1) 2" Hitch Receiver with 2" Drop and 1" Hole, (1) Can Black Spray Paint - If you want to paint it.... Build time including Paint = 30 minutes.....

Inspired me!

Beautiful video❤❤❤❤❤

Thanks for the video. It helped...

My jeep is overheating. What will you recommend? I change the water pump the coolant temperature sensor and steel go over in a half.

How many times did you pump the grease gun

Who gets offended by the flag?

What if we punch a hole into the oil filter and let it drain before we take it off? I do like the idea of the freezer bag.

Am I supposed to remove the l-shaped pin on the tensioner after installation?

I can’t seem to find the 2 amp fuses anywhere.. can I use a 5 amp instead?

You’re the man!

I have a bagger too

I hope you don’t use a trailer for it

❤❤❤ Hello my new friend ❤❤❤Thank you for sharing the great video❤❤

Awesome! Thanks - best use of 16 minutes of my time this month!

I torqued mine to 37 ft-lbs. hopefully is good enough…because I didn’t have the courage to go to 40 ft-lb on old bolts lol. Thanks for the help

i woke up to a new grill delivered and a cranky husband who said the hole was too big for the tank- thank goodness i found your video !! thanks!

why? & how often?

@MrV2u Dear MrV2u, Thank you for sharing this video it is really a stress reliever for some. I have another kind of problem with my ESM, it works properly in All PRND but, when I put it on Drive, I can't shift to - +, is there a way of adjusting this issue? (I am able to move the "handle" left right but cant go from D to 4321...) I opened the upper part as you showed in the vid, There are two thin metallic pieces surrounding the black plastic square that is attached to the white horizontal one (shifter)... Should these be the problem? Could they be cleaned or adjusted? Many thanks😊😊😊

Is this vinyl

Does the vinyl hold up to winter months?

Thanks!! Didn't want to bend the metal bar. Video helped right out. Used Vice Grips.

What size is the retaining nut? I think I overtightened it last time. my crescent wrench and monkey wrench are not doing it.

If it gets wet does it expand? Thanks for the great video!

There is a retaining rod provided with the cover that should be screwed with the plastic nut, otherwise the cover will open very quickly with the clippings pushing out. And according to the instruction leaflet, you should remove the chute, it is useless anyway with the kit, it did remove mine and nothin is blowing out.