the liner was twisted on the back side was it fixed?

kzfaq.info/sun/PLYEJFyGck7RFkR-e32Vw_ywL9MzgbsU8t&si=pA-vqWFI46kk0PD8

Do you need an automation panel for SWG?

Can you please tell me what I should do when the test strip does not show the light brown color. Should I increase or decrease hardness?

Excellent video and I’m about to do this but what is the glue you used? It didn’t look like that was any of the Loctites, which are more aggressive and could make removal of the gasket later a difficult task.

So glad you guys did that, but don’t call it instructional that you’re not gonna give instructions

Great video, easy to follow and it worked. Thanks

you saved me a lot of stress, thank you

I had a customer this year blow-up a chlorinator, my first question was are you okay. Even the base was in pieces

Thank you so much!!! It was the O ring we had no idea who took it out. This was very helpful and fast way to find the solution

What speed to put pump?

I would recommend using Taylor salt water test kit, not a strip. Way more accurate.

That didn’t work at all on mine

i am having issues with my hayward aquarite system. The only light I see green is power. I tried to recalibrate it by turning it off then on, like in your video and no change. The numbers on the screen do not move, unless I hit the diagnostic button. Had my sat cell tested and no issues. My water can't hold free chlorine. About 31,000 gallons and I have been adding a case of shock every week and within 3 days, 0 FC. I tried to locate the T on my screen and it is no where to be found. I am using the T15. I get my water tested and the salt is within the range. My voltage is 32 then I hit diagnostic button and I see 0.00 which is my amps on my cell. How do I know if my mother board is bad or is it is the entire Hayward system?

why not simply get it empty watering the garden & remove it until april ?

Spend more time showing/ explaining how to reassemble the (most difficult step) bottom manifold part. Any hacks would be EXTREMELY helpful. Taking a long time & frustrating..

Thanks. Your images of basic parts and internal mechanisms was super helpful. It was excellent teaching - assume nothing. For me this video clarified quite a few internal things, and I've been successfully servicing pools for five years now.Never too late to learn. Many thanks. Australia

Thanks guys!

hi. how do you use the fetures 3 and 4?

This is 2016 as fck

At 2:55, you lubricate the gasket. What lubricant do you use?

If you don't have a bypass, can you just turn off the heater and the water will still flow through it to the return line? Or does the heater need to be on? Sorry, I'm new to those things...

Yup, turn off the powrer stuck my hand into the impeller....lost of leaves. First hint was that basket had partially ripped. Thanks for the inputs.

Question, would you recommend it for kidney shaped pools or Cloverleaf shaped pools

Not sure why they make you “upgrade” to finer filters. $$

Wow they gave me a full impeller disassembly instruction for waterway executive... thanx for the super helpful vid

Everything here is common sense except for removing the cap with the strap wrench, which is glossed over at 1:17. The cap will likely be nowhere near that easy to twist, and also you can't put a strap wrench on the base of the cap as instructed, the lip is too small to grip there. Instead you have to put the strap on the top of the cap and if there is a safety tag in the way there you will need to cut a slot behind the tag to make room for the strap. And you may (will probably) have to use way way more force than shown here.

Your video had the best explanation of where and how to set up the flow gauge reader. That part was very confusing to me in the instruction manual.

Is there a way to, on for example, for a one time need to run the pump for 48 hours straight ( for a Phosphates cleaning) run time, run the pump?

What is the cost to switch roughly?

i couldn't get mine loosened but found a specialty wrench just for this for $10 on amazon

Before pouring sand in, fill tank 1/2 with water so the sand is boyant and wont damage laterals.

Very helpful for my Hayward NSF-50, thanks !

Would water come out if the pump is shut off? I am concerned that if i take it off all the water will start coming out like a flood!

It's amazing how everyone thinks everyone has a smart phone. I am old and retired and do not need one so I don't have one. How can I make sure I choose the right motor or will you continue to discriminate against the elderly?

Good stuff. Very useful. Thanks so much !

Nice video. Question, did you guys realize after putting the dirt back down around the pool that you need to install the pvc piping the returns and pump?

It was the O ring! Thank you! Simple things I didn't think of. I've recently fired my pool company after discovering how fraudulent they were and have been assuming pool care on my own. It's really not that difficult, kinda therapeutic in fact, but sometimes I get thrown for a loop. Thanks!

The instructions say not to use an extension cord but I may have to for it to reach my entire pool. Is there a reason why I shouldn’t use an extension cord?

How do I take the discharge off to put on another motor?

Thank you for getting right into it.

My Hayward system has the power light on but not the generator light. No other lights are on. What should I do? Already tested the salt cell itself and they told me it’s still working. I even cleaned it. Reply

Our skimmer door seems to get stuck in the 2/3 of the way up position allowing very little water flow when the pump is on. When I manually go push the skimmer door down then it is fine and gets started ok. If I don't manually push it down it seems to stay stuck in the up position. I'm not finding debris or other items in the sides as to why it might be staying stuck on the plastic on the sides in the up position. Any advice?

Will a leak at the SP715 valve drain the pump well overnight? I rebuilt the valve with a GO Kit 39, but the non-metallic/plastic gasket/bearing hole was too small to go over the shaft, so I opened it up with a Dremel tool, figuring the O-rings on the shaft provided the seal. There's a small amount of water around the bearing all the time, and the pump well drains down to the top of the basket.

I did this, now the motor is very noisy, with high pitched noise. What'd I do wrong? Thank you

My pre-filter lid only rotates about a half an inch to lock, maybe 10°. It looks like the lid in this video rotates about 30°---should mine rotate further?

I had a new single speed Hayward one horsepower pump installed for my inground pool a number of months ago. From the beginning it was making too much noise I felt, and it had a large maybe 4 inch air bubble under the lid. The installer said that's because this pump draws more water than the previous one and it's not getting enough water flow from the 2 inch piping, and/or let it run overnight to get the air out all sorts of stuff. From the beginning when locking the lid it would only turn about half an inch to lock recently it was losing its prime overnight, and starting again in the morning and would run dry for I don't know how long before noticed it a couple times and stop the pump open the lid added more water and when I restarted it would prime again after a little while. But after I used Magic Lube II silicone that I had on hand and the bubble became about 1 inch diameter and the pump was quieter, and it kept its prime overnight. I was annoyed that the installer gave all sort of excuses when it was really just it needed lubricant or the the lid wasn't right to begin with. I pointed this out to the pool guy this morning, and he said that he services several other pools with the same pump, and the lid will rotate 90° to lock, which is my expectation based on previous pumps. So is this a defective lid or the wrong lid for the pump? I paid for a new pump. Early on when I asked the installer about the small travel to lock it he said that's normal, but I have my doubts. I see the lid on your pump looks like it rotates about 30°.

Why could there be imense water pressure on one return jet and the other 3 are weak? Is that a clog?

What happens if you power up a wired 230 v to a 115v power input ?

do i need chlorine if my pool has a roof