If your'e just changing barrel and piston, most of this is unnecessary
@TerryBoyum2 күн бұрын
0:54 0:58 canouceantheonethatlnthesaw
@user-xs1fm2kb1n4 күн бұрын
Lo nesecito b en español
@knightday19737 күн бұрын
Thanks - perfect video. BTW T27 Torx for metric
@Judd99913 күн бұрын
useless video
@lolwhittingham14 күн бұрын
Womens pathetic voice on these vids now. Bad enough on football.
@izzycamaro20 күн бұрын
Thanks a lot
@user-or5vc5vj3h21 күн бұрын
I did all this right and the spring or tensioner is just not cooperating on my Stihl 420. Any advice.
@milos133627 күн бұрын
Where is the slip washer, that goes before the nut?
@davecarolynj28 күн бұрын
This isn’t a recoil assembly. This is a chain replacement. Please retitle your video. Extremely unhelpful.
@olliechatwin17829 күн бұрын
Great and all but I’m looking for how you retension the existing pull start, I know how screws work.
@sluggonotnancy6178Ай бұрын
This guy must be trans.
@joespeciale5875Ай бұрын
Great clear short video-nice job!
@martinlopez5297Ай бұрын
Lo puede traducir en español
@1neAdam122 ай бұрын
Whoa, you got GT85! Can't find that stuff anymore. One thing it works great for is using it as a protectant on Thule style roof cargo carriers. Gives it a great lasting shine and won't attract dirt.
@ronaldsneek2 ай бұрын
Indeed hands in the way, show what you put on it. And, what goed over after the things you placed on the video, the strimmer isn't ready to go now is it?
@stevenolan79722 ай бұрын
What a shroood? You mean shroud?
@MISTERPRESIDENTELECT2 ай бұрын
Only God or the Devil can remove the wheel from my 50yo mixer, and both of them are pissed off with me at the moment.
@SethReed-ip5zl2 ай бұрын
Move your hands!!
@garethturgoose94382 ай бұрын
Excellent instruction
@user-pu8pz8fg3k2 ай бұрын
Переснимите
@robertmort59943 ай бұрын
Impossible to see details because fingers are in the way and done too quickly
@MrSSB513 ай бұрын
Pretty basic video. Seeing the gasket stack layout would have been helpful also torque values and was there any thread anti seize compound applied?
@jamesevans83453 ай бұрын
Very helpful
@ronshlg3 ай бұрын
Thank you this helped.
@wendellleytham92183 ай бұрын
Way too fast and not enough close up detail.
@mikeridge32293 ай бұрын
Too quick and forgetting details
@instagrammemesmemes23803 ай бұрын
Hi anyone know how to tune this carby as there are not screws like other ones I have seen
@user-nk7gl4vq1x4 ай бұрын
Can't see a thing on this for the big fists in the way
@just_braap19354 ай бұрын
15w40 oil
@PakenhamBetterRentals4 ай бұрын
no one shows howto swap the coupling
@PaulStott-qo5dw4 ай бұрын
Simple when you know how.. thanks
@patrickandrews64274 ай бұрын
That was great and easy to follow thanks
@74quo4 ай бұрын
My spark plug is different 🤔
@xx-cv4fp4 ай бұрын
👍
@danielsavage49434 ай бұрын
Hi how many bolts and nuts you use for this and the sizes that’s for the conversion to petrol
@peters26205 ай бұрын
What about washing the sponge outer in oil before putting it on?
@robbiemorrow34735 ай бұрын
4:16 I found this video more helpful than a 11 minute video. TY4SHARING 🙏
@gilmarpires21075 ай бұрын
Obrigado 👍👏👏👏
@tonyalways71746 ай бұрын
Great tip 👍🏻
@lufix20116 ай бұрын
Thanks
@user-ii3cr9zx3m6 ай бұрын
complete waste of time! only shows how to remove and install the cover. no where does it show anything about "recoil"
@charleshill92367 ай бұрын
Should I wear hearing protection when running my saw in the bathroom?
@rickhill27172 ай бұрын
WHAAAT???
@outdoorsnevada41387 ай бұрын
very simple process but an important step to keeping your saw running
@matthewharmer16568 ай бұрын
What about compressing the piston rings??
@rubennavarro20038 ай бұрын
Why would you have text over the video?!?😮
@bjiggles81458 ай бұрын
Sadly this video does not (IMO) give proper instruction for actually using the tensioner correctly and failing to do so can break your tensioner or give you improper tension: 1) Ensure that the tensioner assembly is on the "loose setting" (indicated by the arrow on the plastic tensioner nut pointing at the "O" on the cover) when you put on and tighten the front cover. 2) Put on the rear cover when you can visibly see that the black plastic arm of the tensioner assembly is touching the white peg that it pushes against to create the tension (It's not the best view, but you can see this from 2:34 to 2:44 in this video) and have the nuts on barely finger tight. 3) Tighten the belt by turning the plastic tensioner nut clockwise until reaches a noticeable stop. You will feel resistance and the arm assembly should slide forward slightly as you turn the tensioner nut. 4) After you hit the stop, fully tighten down the rear cover nuts. This is from the user's manual which I have in front of me although I rephrased it a little so the video could be used as visual aid. You're correct @jlit6428, this is one of most important aspects of the entire process and they really didn't explain it very well.
@johnwayneschaefer85189 ай бұрын
Horrible instructional video !!! Move ur damn fat hands and show more detail.
@licoskeete64179 ай бұрын
I gave you a thumbs down because, you did not instruct the directions of how the pistons rings should be placed on the cylinder.