How can I find TDC ?

Man what a job. Wow! How much to get this done.

is it danger this steering sound?

Did you have to get the cylinder head resurfaced?

All that just to take off the valve covers ! This engine must have been designed by Ducati.

Here is the example how you should not do. The guy don't know BMW.

My head gasket is apparently blown and I want to fix it myself. I just hit 90,000 miles I’m so upset.

How u didn’t re machine head !!! Honda said no

Great video Thank you

the clutch types are deferent?

Great video. My sienna is 2009 with the same p0430 error code. Is it the same Cat that I need to replace?

Thanks For Greats Video Do You Are Best Of the Best

what thread pitch bolts did you use tah pull the pump out

This guy makes it look so easy

Quoted from a shop as $550. I appreciate your walk-through helped save me a ton Thanks!

This is the BESt video on KZfaq on how to replace the oil pickup tube o-ring. The front diff does NOT need to be completely removed from the vehicle,, unlike the other videos on KZfaq which turn this into a tremendously huge project involving completely removing the front diff, disconnecting both the front drive axles and the driveshaft, and then disconnecting the steering column from the steering rack.

This was professionally done ✔️ thank you

You might as well put a new pump since you’re already there

But what about the spring? Do you need to support that in any way?

are you holding the OK button or the left arrow button?

This only works if your cams are still good. If you have any excessive wear of any kind you’ll have to replace the four cams did which ALWAYS seem to be on back order!

Been trying for days and listening to these ppl ramble. I thought to take the batteries out before. This worked...sometimes its always the simplest things to do!!

Do all 3.3 v6 Toyota engines share all the same cats?

Does a torque specification apply to a 2007 Cadillac Escalade

I have 300 that ticks it needs fixed

I have to do a rebuild on my 2011 silverado 1500. This video really helps. Thanks!

Do any of you have problems with your alternator i done put three on mind in 2 years let me.know

Thats cam shifting can crack the head at bearing seat

Did you send the cylinder head to the machine shop?, I don't see If you make the valve adjustment?

🎉🎉🎉🎉

Good video, did you think Amazon starter are trusted?

Interesting way of doing this. Looks legit, if you are careful. Going to dive into the pentastar in my 2015 dodge grand caravan today. Just one thing...they are called lifters, not pushrods. Other than that, good video. Thank you.

My bottom two 12mm bolts on the timing cover went from righty tighty to righty loosey when torquing to 24 ft lbs. :/

What was the time frame to do this ?

Ja pierdole wow dziękuję ❤❤❤

Nice video hands down

You forgot to include putting back the tensioner pulley… Great vid

Great video very informative and easy to understand… I’m about to tackle this job on my 2012 Dodge Charger! Thank you!

Jesus christ disassemble the truck fuck what's the cost for that job approx.

That's an amazing repair. I have a question, though. Since you were able to remove the front cap (29:46) to get the cam shaft up high enough to replace the front rods and rockers , couldn't all of the rods and rockers (for that cam shaft) have been replaced at that point? I have a 2015 that's beginning to tick, so, I expect to be doing this repair.

U r a f-kin genius

Thank you.. While it did not show everything, it pointed me in the right direction. The AC lines on the passenger side, and a large wiring harness on the drivers side make getting the rad out difficult. But a few zips ties cut and some careful pushing of the AC lines and the rad came out. Everything else is spot on... Ty again.

Nice video on explaining everything boss. Question does this apply similar to a non afm 5.3

Was that high beam or low beam?

I Always clean the radiator 'cause have particles. Thanks buddy.

A2Z Auto Masters. Great video, you are very detailed. My one question is the torque numbers you listed are much different than the honda instructions for a 2018 Accord 1.5 t. Am I reading something wrong?

A couple years ago I carefully watched this video and successfully made the repairs on the driver side. Now it's time for the passenger side... Wish me luck! Thanks for the video!!

Great job. Thank you for sharing

Great job on your video

My 2018 honda accord with 105,000 miles and it already has a blown head hasket