I want to purchase a JD snowblower for my x530. Is this x540 the same set up? Do I want the 44 or 47 for blower?
@terryhamielec13037 ай бұрын
You need electric lift kit to raise snowblower, too heavy for foot pedal
@pierre662510 ай бұрын
Thanks
@travismagalas865110 ай бұрын
Is there any videos on how to take the sieves out and replace them ?
@PilotLifeNet Жыл бұрын
so when do you hook up hydraulics to the deck and hook up the mower pto shaft.
@MC-zx1qm Жыл бұрын
What is the part number for this blower?
@RCALivingStereo Жыл бұрын
I just bought a new x738, is this the same steps on a new one?
@davidd1395 Жыл бұрын
With all due respect, you didn’t mention what needs to be done to the valve on the hydraulic 4 hose block on the tractor between blower and mower operations. It is a must.
@luckymutibo9848 Жыл бұрын
Working on a S680,rubber bushing are new only done one soya harvest, combine is having a strange shake when I run the shaker pan....what cub be causing the problem, have taken out the shaft that drives the pan for straightness testing, also found the prop shft from rotor drive has worn universal joints.
@scottweisel3640 Жыл бұрын
I bought a CC a few years ago because I live close to a dealer with a service center. It works great but I can see from this video why I made a mistake by not buying a JD. These operations on a CC are very time consuming and labor intensive. I have no complaints on how the tractor performs, but did not realize what I was getting into on the snowblower install.
@brianschmitt5013 Жыл бұрын
This was helpful - thank you for an easy to follow set of instructions
@harlanfrey4413 Жыл бұрын
How do you loosen up a feeder house chain on a 9670 STS combine
@tf7274 Жыл бұрын
There should be a tensioning bolt near the front of the feederhouse on either side...not sure if the adjustment is in the manual, but most likely.
@salmaabdulai197 Жыл бұрын
Hi Dave, how do I adjust the concave and sieve for Teff harvesting? or do I need a new sieve for Teff harvesting?
@tf7274 Жыл бұрын
Depends which crop you are combining. We combine wet corn and you have to run a lot of air...we put the upper sieve the size of our biggest kernel for the year...and bottom wide open. The rest is concave and cylinder speed...there is never a need to re-thresh any corn if your cylinder and concave are set properly. You just take cob pieces and demolish them and send them thru both sieves and into the tank.
@jerhalco2 жыл бұрын
Looked like he avoided pulling on the quack grass. You should have edited
@danielchase38752 жыл бұрын
Never mentioned that you gotta turn the knob* on hydraulics
@davido5925 Жыл бұрын
Thank you! If it hadn’t been for you I’d have no clue, I can’t believe he didn’t mention it!
@deebee51962 жыл бұрын
Looks self explanatory to me. My old 265 blower had wheels to move it around, this will make my summer/winter transition more thought out.
@miguelbaldominos12782 жыл бұрын
En español
@dledward99902 жыл бұрын
This video was very helpful!! It includes lots of good points. I have an X739 with auto-connect, and I had do a couple things differently to make the conversion work. For my mowing deck, my drive shaft stayed with the tractor, in a hanger (did not stay with the mower deck). So I had to move the mower drive shaft (with auto-connect) out of the hanger, and attach it to the PTO before driving over the deck. (Maybe I didn't have to attach it to the PTO yet, but I wasn't able to get it out of the hanger with the deck mounted.) And the bar that lifts the deck was locked into a fully up position (for when the blower was on). On the right side of the tractor, I had to pull a pin out that was locking a hook in place that was holding the bar up. Once the pin was out, I could rotate the hook, releasing the bar, lower the bar (a small distance) rotate the hook into an out of the way position, and reinsert the pin, locking the hook out of the way. My bar did not drop down far enough to engage the deck with just the hydraulics, so it helped to (with the parking brake on) put my foot on the bar to push it down while engaging the hydraulics.
@marybroussard34782 жыл бұрын
Hi n
@ShermanT.Potter2 жыл бұрын
So you're not supposed to run a few thousand acres on the hold downs? Lol, my Dad never replaced them and between the hold down and sickle wear, it started wearing into the sickle bar, looks wicked.
@gary77382 жыл бұрын
O no
@timnichols90153 жыл бұрын
Also check the auger for cracking and weld that up before it breaks in half……
@8700I3 жыл бұрын
Hmm, he’s stuttering a lot
@deere72273 жыл бұрын
So the purpose was to spread quack grass more evenly, work below optimum seed depth for soybeans all while the field was too wet?
@DustonDiekmann3 жыл бұрын
tips for why my blower only lifts 1-2 inches off the ground in front?
@freecycling66873 жыл бұрын
Haha, everything just about jumped into its place. In reality, each of those steps represents a struggle, some small, some large, against binding parts, belts that don't stretch, L-pins that don't line up, etc. etc.
@rotorbeam13 жыл бұрын
To improve on the handling of the handle for the chute movement, cut off the turning handle and use a cordless drill or even better a usually hardly used, cordless screw driver. An inexpensive way to enjoy the snow blower by motorizing the function.
@Petrochemtester3 жыл бұрын
that clump of grass at 1:46 sure seemed like it was still rooted....? will 3" depth and minimal disc angle really get the deeply rooted weeds?
@coreymartin5185 Жыл бұрын
it's only meant to chop residue, not till up weeds.
@rosshanson29073 жыл бұрын
I understand the gap is not adjusted by the idler pulley. It is adjusted at by the all thread bolt with double nuts. Spin the front nut to the back nut, then turn together which turns the all thread bolt which adjusts the gap.
@JoseMendoza-bi9mo4 жыл бұрын
No podrian pasar esto en español
@hellwithit4 жыл бұрын
lol my boss has a better crop of grain in the fields he didn’t plant than he did in the ones he actually planted. Told him that he was spraying the wrong field. But it’s last year volunteer crop. lol.
@toddjacobs56604 жыл бұрын
Great video ...
@deltatango36534 жыл бұрын
Thanks. I appreciate your videos. 9770, S670, S680 operator
@march29944 жыл бұрын
For the x534 would you have to disable the zero turn too?
@josephmendez2715 жыл бұрын
What's the part number for the blower. And does it fit on a x390
@alexpb95 жыл бұрын
Would you say lateral tilt is a must for Soybean and corn harvest? Or can I get away without lateral tilt?
@haroldmargaretmiller43364 жыл бұрын
It’s definitely worthwhile having.
@eastamericantrains5895 жыл бұрын
The old gravely riders have a very similar set up. They have the pto right in front of the transmission and have a driveshaft that runs up to the front to work the blower. Kind of cool to see the old ideas carrying on.
@eastamericantrains5893 жыл бұрын
@Larry Jackson fuck off scammers
@larrymcalister11005 жыл бұрын
Have you ever had it pop out while you are running?
@user-xh6rn4vu6b5 жыл бұрын
Какая неисправность если загорелась лампочка жолтого цвета со знаком восклицания,на оприскивателе джондир 4730
@DavidWithers6 жыл бұрын
Terrible machine will over heat hydraulics in 30 minutes
@RickNethery6 жыл бұрын
Very nice setup, I already have a small tractor, but would love to have that attachment
@max53147 жыл бұрын
what tractor is that
@RickSwartwood7 жыл бұрын
What Cab is that?
@FiveCentsPlease7 жыл бұрын
Very impressive. Once you know the steps, you can be ready to work in about 15 minutes. I just watched the snowblower install from Husqvarna and they had two people screwing around with bolts, washers and ratchets, taking parts off and putting parts on and they started with the mower deck already removed. So it looked like the Husqvarna install would take over an hour. I don't even live where I need this type of snow blowing equipment but if I ever do, I will be getting John Deere.
@tedhill3237 жыл бұрын
Great video, this has been very helpful to me as the owner of a new X738 with auto-connect. I followed the procedure in this video to remove the mower deck. Then disconnected the auto-connect drive shaft from the tractor and hung it into the U-shaped bracket. But then I found it very difficult to raise the lift-linkage high enough to be able to latch it with the storage hook. Finally I used the hydraulics to lift the lift-linkage all the way up and was then able to latch it in the up position with the storage hook. Two questions: 1. Should I need to use the hydraulics to raise the lift-linkage? It looks so easy in the video and the video does not mention using the hydraulics to raise it. It looks like you can just push it up manually. 2. Once the lift-linkage is latched in its up position, does the hydraulic connection to the lift-linkage need to be 'shut off' in some way? Or will the hydraulic connection to the snowblower simply override the connection to the lift-linkage? Thank you.
@frankaldo4813 жыл бұрын
sorry to be off topic but does any of you know a way to log back into an instagram account? I stupidly forgot the password. I would love any help you can give me!
@finnalberto16083 жыл бұрын
@Frank Aldo instablaster :)
@frankaldo4813 жыл бұрын
@Finn Alberto I really appreciate your reply. I got to the site thru google and I'm trying it out atm. Takes a while so I will get back to you later when my account password hopefully is recovered.
@frankaldo4813 жыл бұрын
@Finn Alberto it did the trick and I actually got access to my account again. I'm so happy! Thanks so much, you saved my ass!
@finnalberto16083 жыл бұрын
@Frank Aldo Happy to help =)
@Boobtube.8 жыл бұрын
He never hooked up the PTO shaft from the blower to the tractor.
@MRIDNETGUY20047 жыл бұрын
XboobtubeX 😑😑
@mrbubetube6 жыл бұрын
good time to find out how well the blower works as a plow
@MRIDNETGUY20043 жыл бұрын
@@mrbubetube or more as a box blade.
@lukaszbandola38218 жыл бұрын
I have x500 and just bought two stage 47" snow thrower with quick hitch, I can lift with foot pedal but is not running, any suggestion?
@frontieragturf49188 жыл бұрын
+Lukasz Bandola Is the PTO engaging?
@teekay_18 жыл бұрын
Did you have to tie into the hydraulic system? Or does it use the lift system already in place for the mower deck?
@calebness37698 жыл бұрын
Could you guys make a video on how to install a blower on a STX 38
@frontieragturf49188 жыл бұрын
+Caleb Ness We currently do not have any STX 38 models with snow throwers in stock. Thank You for the suggestion though!